Tippmann CARVER ONE Owner's manual

Brand: Tippmann

Model: CARVER ONE

Type: Owner's manual

Tippmann CARVER ONE is an accurate and durable paintball marker, designed for recreational and competitive play. It features a barrel sleeve for safety, a trigger safety to prevent accidental discharge, and a velocity adjustment system to ensure safe and accurate shooting. With its easy-to-load hopper and simple maintenance requirements, the CARVER ONE is a great choice for both beginners and experienced paintball enthusiasts.

CARVER ONE

Paintball Marker

Owner’s Manual

WARNING

THIS IS NOT A TOY. MISUSE MAY CAUSE SERIOUS INJURY OR

DEATH. EYE, FACE, AND EAR PROTECTION DESIGNED FOR

PAINTBALL MUST BE WORN BY THE USER AND ANY PERSON

WITHIN RANGE. WE RECOMMEND YOU BE AT LEAST 18

YEARS OLD TO PURCHASE. PERSONS UNDER 18 MUST HAVE

ADULT SUPERVISION WHEN USING THIS PRODUCT. READ

THE OWNER’S MANUAL BEFORE USING THIS PRODUCT.

WARNING

SAFETY IS YOUR RESPONSIBILITY

READ AND FAMILIARIZE YOURSELF AND ANY OTHER USER

OF THIS MARKER WITH THE

SAFETY INSTRUCTIONS

IN THIS

MANUAL. FOLLOW THESE INSTRUCTIONS WHEN USING,

WORKING ON, TRANSPORTING, OR

STORING THIS MARKER.

ALWAYS KEEP THE TRIGGER SAFETY IN SAFE

MODE UNLESS IN A SHOOTING SITUATION, AS

DETAILED IN TRIGGER SAFETY INSTRUCTIONS.

ALWAYS KEEP THE BARREL SLEEVE

INSTALLED WHEN NOT IN A SHOOTING SITUATION,

SEE BARREL SLEEVE INSTRUCTIONS BELOW.

Barrel Sleeve Installation Instructions

1. InserttheBarrelSleeveontotheBarrelandloopthecord

overthetopofthereceiverandpositionatthebackofthe

gripasshown.

2. Adjustthecordlengthretaineruptothebackofthegripby

pullingthecordthroughituntiltheretainerissnugagainst

thebackofthegrip.Keepingthecordastightaspossible,leave

justenoughcordelasticitytopullthecord/retainerupoverthetop

ofthemarkertoremovetheBarrelSleeveforring.

3. Afterthecordlengthisproperlyadjusted,lockthecordlengthby

tyingaknotinthecordagainstthebackoftheretainerasshown.

4. Beforeandafterplaying,inspecttheBarrelSleeve.Replacethe

BarrelSleeveifthesleeveorcordisdamaged,orathereisalossofcordelasticity.

5. CleantheBarrelSleevewithplain,warmwaterandstoreoutofsunlightinadryareawhennot

inuse.

Introduction

CONGRATULATIONSonyourpurchaseofyourTippmann®paintballmarker.WebelieveourCarver

One™markertobethemostaccurateanddurablepaintballmarkeravailable, and it is proudly

manufactured by Tippmann.TheTippmann®CarverOnemarkerwillprovideyoumanyyearsof

dependableserviceifcaredforproperly.

PleasetaketimetoreadthismanualthoroughlyandbecomefamiliarwithyourTippmann®Carver

One™marker’sparts,operation,andsafetyprecautionsbeforeyouattempttoloadorrethis

marker.Ifyouhaveamissingorbrokenpart,orneedassistance,pleasecontactTippmannConsumer

Relationsat1-800-533-4831forfast,friendlyservice.

Warning / Liability Statement

ThismarkerisclassiedasadangerousweaponandissurrenderedbyTippmannSports,LLCwith

theunderstandingthatthepurchaserassumesallliabilityresultingfromunsafehandlingoranyaction

thatconstitutesaviolationofanyapplicablelawsorregulations.TippmannSports,LLCshallnot

beliableforpersonalinjury,lossofpropertyorliferesultingfromtheuseofthisweaponunderany

circumstances,includingintentional,reckless,negligentoraccidentaldischarges.

Allinformationcontainedinthismanualissubjecttochangewithoutnotice.TippmannSports,LLC

reservestherighttomakechangesandimprovementstoproductswithoutincurringanyobligationto

incorporatesuchimprovementsintoproductspreviouslysold.

Ifyouasauserdonotacceptliability,TippmannSports,LLCrequestsyoudonotuseaTippmann

Sports,LLCmarker.ByusingthispaintballmarkeryoureleaseTippmannSports,LLCofanyandall

liabilityassociatedwithitsuse.

Safety Is Your Responsibility!

Trigger Safety

Familiarize Yourself with Safety...

Theownershipofthismarkerplacesuponyouthetotalresponsibilityofitssafeandlawfuluse.You

mustobservethesamesafetyprecautionsasyouwouldanyrearmtoassurethesafetyofnotonly

yourselfbuteveryonearoundyou.Outlinedherearesomegeneralprecautionstobeawareof.The

usershouldatalltimesusecautionandcommonsensewhenusingthismarkerandalwaysremember

thatthegameofPaintballcanonlysurviveandgrowifitremainsSAFE!

• Donotloadorrethismarkeruntilyouhavecompletelyreadthismanualandarefamiliar

withitssafetyfeatures,mechanicaloperation,andhandlingcharacteristics.

• Handlethisandanymarkerasifitwereloadedatalltimes.

• KeepyourngerofftheTriggeruntilreadytoshoot.

• Donotlookdownthebarrelofapaintballmarker.Accidentaldischargeintotheeyesmay

causepermanentinjuryordeath.

• KeeptheTriggerSafetyintheSafepositionuntilreadytoshoot(seeWarningmessage

above).

• Keepabarrelsleeveinstalledonmarkerwhennotshooting(seeWarningmessageabove).

• Neverpointthemarkeratanythingyoudonotintendtoshoot.

• Neverreyourmarkeratanythingyoudonotintendtoshootbecausetheremaybe

paintballsorforeigndebrislodgedinthechamber,barrel,orthemarker’svalve.

• Donotshootatfragileobjectssuchaswindows.

• Neverreyourmarkeratpersonalpropertyofothers.Thepaintballimpactcancause

damageandthepaintcanstainthenishofautomobiles,houses,etc.

• Alwayskeepthebarrelpointeddownorinasafedirection,evenifyoustumbleorfall.

• Eye,face,andearprotectiondesignedspecicallytostoppaintballsintheformofgoggles

andfullfacemaskmeetingASTMSpecicationF1776mustbewornbytheuserandany

personwithinrange.

• Nevershootatapersonwhoisnotprotectedbyeye,face,andearprotectiondesignedfor

paintball.

• Pressurizeandloadamarkeronlywhenthemarkerwillbeimmediatelyused.

• Storethemarkerunloadedanddegassedinasecureplace.

NOTE:Beforestoringordisassembling,besuretoremovepaintballsandair/CO2cylinder

(seeUnloading Your MarkerandAir/CO2 Cylinder Warnings),puttheTriggerSafetyin

theSafepositionandinstallthebarrelsleeve.

• Donoteldstriporotherwisedisassemblethismarkerwhileitispressurized.

• Dressappropriatelywhenplayingthegameofpaintball.Avoidexposinganyskinwhen

playingthegameofpaintball.Evenalightlayerofclothingwillhelpabsorbsomeofthe

impactandprotectyoufromthepaintballs.

• Keepexposedskinawayfromescapinggaswheninstallingorremovingtheair/CO2

cylinder,orifthemarkerorair/CO2cylinderisleaking.Compressedair,CO2,andnitrogen

gassesareverycoldandcancausefrostbiteundercertainconditions.

• Useonly.68caliberpaintballs.Neverloadorreanyforeignobjects.

• Avoidalcoholicbeveragesbeforeandduringtheuseofthismarker.Handlingmarkerswhile

undertheinuenceofdrugsoralcoholisacriminaldisregardforpublicsafety.

• Avoidshootinganopponentatpointblank,6feetorless.

• Familiarizeyourselfwithinstructionslistedontheair/CO2cylinder.Contacttheair/CO2

cylindermanufacturerwithanyquestions.

• Alwaysmeasureyourmarker’svelocitybeforeplayingpaintballandnevershootatvelocities

inexcessof300feetpersecond(seeVelocity Adjustment instructions).

• AlwayskeepinmindthatthesportofPaintballisviewedandjudgedbyyoursafeand

sportsmanlikeconduct.

Getting Started

• Eyeprotectiondesignedforpaintballusemustbewornbytheuserandanypersonwithin

range.

• Donotdisassemblethismarkerwhileitispressurizedwithair.

• Donotpressurizeapartiallyassembledmarker.

• Readeachstepcompletelybeforeperformingthestep.

NOTE:Carefullyhandstartallthreadedpartswhenassembling,anddonotover

tighten,asthismaypotentiallystripthethreadedparts.

1. Prepare Marker for Air/CO2 Cylinder Installation.

a. ApplyTippmannoiltotheBarrelO-ring.

b. InserttheBarrelintotheReceiver.

c. CarefullyturntheBarrelclockwisebyhanduntiltight.

2. Air/CO2 Cylinder Installation.

ReviewAir/CO2 Cylinder Safety Tips.

a. PuttheTriggerSafetyintheSafepositionandinstall

theBarrelSleeve.

b. Cockthemarkerbyslidingthebolthandlealltheway

backuntilitlocksintoplace.Alwayskeepmarkerin

thecockedpositionwhenattachingair/CO2cylinder

tothemarker.Thishelpspreventanaccidental

discharge.

c. Lubricatetheair/CO2cylindervalveO-ringwitha

littleTippmann®oil.

d. Inserttheair/CO2cylindervalveintotheAirSupplyAdapter(ASA)(29)atthebackendof

themarkergrip.

e. Twisttheair/CO2cylinderclockwiseintotheASAuntilitstops.Usecautionasthemarkeris

nowcapableofringafteryouputtheTriggerSafetyintheFireposition.

(Ifthetankisfullandyoudonotheartheair/CO2cylinderengage,thepinvalvecould

betooshortorthepinvalvesealisdamaged,followtheAir/CO2 Cylinder Removal

instructionsandtakeyourair/CO2cylindertoa“C5”CertiedAirsmithforinspectionor

contactthecylindermanufacturer).

3. Loading the Hopper

TheBarrelSleevemustbeinstalledandtheTriggerSafetyintheSafeposition.

a. MakesurethattheFeedElbow(9)andHopperarecleanandfreeofsharpedgesor

debris.Thiskeepspaintballsfrombreakingprematurely,andallowspaintballstofeedtothe

marker’schambersmoothly.

b. InstalltheHopperneckintotheFeedElbow.

c. TightentheFeedElbowBolt(11)usingtheincluded3/16”allenwrench.

d. WiththeBarrelSleeveinstalled,andtheTriggerSafetyintheSafeposition,youarenow

readytoloadthehopperwith.68caliberpaintballs.Donotforceexcessivenumbersof

paintballsintothehopper.

4. Fire the Marker

a. RemovetheBarrelSleevefromthemarker.

b. Pointthemarkerinasafedirection.

c. PuttheTriggerSafetyintheFireposition.

d. Pullthetriggertorethemarker.

Velocity Adjustment

Eachtimeyouplaypaintball,checkthevelocityofyourpaintballmarkerwithachronograph(an

instrumentformeasuringvelocity)priortoplayingpaintball.Verifythatthemarker’svelocityisset

below300feetpersecond(orlessifrequiredbytheplayingeld).

Toadjustthevelocity,usethe3/16”allenwrenchincludedwithyourmarker.TheVelocityAdjustment

Screw(#51inPartsDiagramandshowninFigure3)islocatedonleftsidereceiver.Toreducethe

velocity,turnthescrewinwardorclockwise.Toincreasethevelocity,turnthescrewcounterclockwise.

Donotremovethevelocityscrew.

Unloading Your Marker

1. Eyeprotectiondesignedforpaintballusemustbewornbytheuserandanypersonwithin

range.

2. InstallthebarrelsleeveandputtheTriggerSafetyintheSafeposition.

3. EmptyandremovetheHopper.

4. Gotoadesignatedringarea,removetheBarrelSleeve,andputtheTriggerSafetyintheFire

position.

5. Pointyourmarkerinasafedirectionandreseveraltimestobesuretherearenoremaining

paintballslodgedinthechamberorbarrel.IMPORTANT:Donotuncockyourmarkeras

uncockingyourmarkermaypushaballintothechamberordownintothebarrel,makingit

hiddenfromview.

6. ReturntheTriggerSafetytotheSafepositionandreinstalltheBarrelSleeve.

7. Visuallyinspectthechamberforpaintballs.

8. ReadthefollowingAir/CO2 Cylinder WarningsandSafety Tipsbeforeremovingtheair/CO2

cylinderfromyourmarker.

Air/CO2 Cylinder Warnings

RefertoFigure4.Therehavebeenreportedincidentscausedby

playersunknowinglyunscrewingthecylinder(2)fromthecylinder

valve(1).Thisoccurswhentheplayerthinkstheentirevalve-

cylinderassemblyisbeingunscrewedfromtheairsupplyadaptor

(ASA)ofthepaintballmarker,wheninfacttheyareunscrewingthe

cylinderfromthecylindervalve.

Toavoidthisdanger,itisrecommended(ifyourcylinderisnot

alreadymarked)thatyouusepaintornailpolishtoplaceamark(3)

onthecylindervalve,andplaceanothermark(4)onthecylinder,in

linewiththe#3markasshown.

Wheneveryouturnthecylinderduringremoval,watchthemarks

onthecylinderandthecylindervalvetobesurethattheyrotate

together.Ifatanytimethesemarksstarttoseparateasshownin

Figure5,thecylinderisstartingtounscrewfromthecylindervalve

andyoumustSTOPandtaketheentireunittoa“C5”certied

airsmithforsaferemovaland/orrepair.

NOTE:Thecylindervalveshouldunscrewfromthepaintball

markerinabout3or4fullturns.Ifyounishthe4thfullturnandthe

cylindervalveisnotunscrewedfromthepaintballmarker,STOP!

Taketheentireunittoa“C5”certiedairsmithforsaferemovaland/

orrepair.

Locatea“C5”CertiedAirsmithatwww.paintball-pti.com/search.asp.

Whetheryouhaveaneworusedrellableair/CO2cylinder,youareatriskifanyofthefollowinghas

occurred:

• Thevalveunitwasreplacedoralteredafterpurchase.

• Ananti-siphondevicewasinstalled.

• Thevalveunitwasremovedfromthecylinderforanyreason.

• Anymodicationwasdonetotherellableair/CO2cylinder.

Ifanyoftheseconditionshasoccurred,takeyourair/CO2cylindertoa“C5”CertiedAirsmithfor

inspectionorcontactthecylindermanufacturer.

Air/CO2 Cylinder Safety Tips

SAFETYTIPStoensurethatyourairorCO2cylinderissafeforplay:

• Improperuse,lling,storage,ordisposalofair/CO2cylindermayresultinpropertydamage,

seriouspersonalinjuryordeath.

• Makesurethatanymaintenanceormodicationtoanyair/CO2cylinderisdonebya

qualiedprofessional,suchasa“C5”certiedairsmith.

• Theuseofanti-siphondevicesisnotrecommended.However,ifoneisalreadyinstalledon

yourair/CO2cylinder,orsuchdeviceisdesired,itiscriticalthatyourcylinderbecheckedby

aqualiedprofessional,andyouhavethedeviceinstalledbyaqualiedprofessional.

• Allair/CO2cylindersmustbelledonlybyproperlytrainedpersonnel.

• Cylindervalvesmustbeinstalledonlybyproperlytrainedpersonnel.

• Donotoverllacylinder!Neverexceedtheair/CO2cylinder’scapacity.

• Donotexposepressurizedair/CO2cylindertotemperaturesexceeding130degrees

Fahrenheit(55degreesCelsius).

• Donotusecausticcleanersorstrippersontheair/CO2cylinderorcylindervalve,anddonot

exposethemtocorrosivematerials.

• Donotmodifytheair/CO2cylinderinanyway.Nevertrytodisassemblethecylindervalve

fromtheair/CO2cylinder.

• Anyair/CO2cylinderthathasbeenexposedtore,orheatedtoatemperatureof250

degreesFahrenheit(121degreesCelsius)ormoremustbedestroyedbyproperlytrained

personnel.

• Useappropriategasforyourcylinder.OnlyuseCO2inaCO2cylinderandonlyuse

compressedairinacompressedaircylinder.

• Keepallcylindersoutofthereachofchildren.

• Theair/CO2cylindershouldbeinspectedandhydrostaticallyretestedatleastevery5years

byaDOTlicensedagency.

• Keepexposedskinawayfromescapinggaswheninstallingorremovingtheair/CO2

cylinder,orifthemarkerorcylinderisleaking.CompressedairandCO2gassesarevery

cold,andcancausefrostbiteundercertainconditions.

NOTE:Locatea“C5”certiedairsmithatwww.paintball-pti.com/search.asp.

Air/CO2 Cylinder Removal

1. ReadAir/CO2 Cylinder WarningsandAir/CO2 Cylinder Safety Tipsbeforebeginningthe

cylinderremovalprocess.

2. Eyeprotectiondesignedforpaintballusemustbewornbytheuserandanypersonwithin

range.

3. FollowtheUnloading Your Markerinstructions.

4. Watchthemarksonthecylinderandcylindervalve(asshowninFigure4)asyouturnthe

cylinderapproximately¾turncounterclockwise.Thisallowstheair/CO2cylinder’spinvalveto

closesothatnogasentersthemarker.

5. RemovetheBarrelSleeve.SettheTriggerSafetytotheFireposition.Pointthemarkerinasafe

direction,anddischargetheremaininggasinthemarkerbyrepeatedlypullingthetriggeruntil

themarkerstopsring(thismaytake4-5shots).Ifyourmarkercontinuestore,thecylinder’s

pinvalvehasnotclosedyet(thecylinderpinvalvecouldbelongerthanusual.Becauseofthe

variancesincylinderpinvalveparts,eachcylindervariesslightlyonexactlyhowfarithastobe

turned).Turnthecylindercounterclockwisealittlefurtherandrepeatthisstepuntilthemarker

doesnotre.Onlythenremovetheair/CO2cylinder.



NOTE:Ifduringthisstep,youturnedtheair/CO2cylinderanditbegantoleakbeforeyoupulled

thetrigger,thecylinder’sO-ringshouldbecheckedfordamagebeforeanyre-assembly(see

Repairing Air/CO2 Cylinder Leaksbelow).

6. Aftertheair/CO2cylinderisremoved,againpointandrethemarkerinasafedirectiontoverify

themarkeriscompletelydischargedofgas.

7. MovetheTriggerSafetytotheSafepositionandinstalltheBarrelSleeve.

Repairing Air/CO2 Cylinder Leaks

Themostcommonleakoccursfromabadair/CO2cylindervalveO-ring.ToreplaceavalveO-ring

youmustrstremovethebadO-ringandtheninstallanewone.ThisO-ringislocatedonthetipof

yourair/CO2cylindervalve.ThebestvalveO-ringsaremadeofurethane.UrethaneO-ringsarenot

affectedbyhighair/CO2pressures.ThesemaybepurchasedfromTippmann®oryourlocalpaintball

dealer.

NOTE:Ifanewair/CO2cylindervalveO-ringdoesnotresolvealeak,donotattempttorepairtheair/

CO2cylinder.ContactTippmannSports,LLC,yourlocalpaintballdealer,ora“C5”CertiedAirsmith.

Cleaning and Maintenance

• Eyeprotectionmustbewornbytheuser.

• Toreducethechanceofanaccidentaldischarge,followtheUnloading Your Markerand

Air/CO2 Cylinder Removalinstructions.

• Donotdisassembleamarkerwhileitispressurizedwithair.

• Donotpressurizeapartiallyassembledmarker.

• Followwarningslistedontheair/CO2cylinderforhandlingandstorage.

• Familiarizeyourselfwithinstructionslistedonair/CO2cylinder.

• Contacttheair/CO2cylindermanufacturerwithanyquestions.

• Donotuseanypetroleumbasedcleaningsolvents.

• Donotuseanycleaningsolventsthatcomeinaerosolcans.

NOTE:Petroleumbasedproductsandaerosolproductscandamageyourmarker’sO-rings.

Tocleanyourpaintballmarkerexterior,useadamptoweltowipeoffpaint,oil,anddebris.

Tocleaninsidethebarrel:

1. RemovetheHopper.

2. CompletelyloosentheFeedElbowThumbNut(10)fromtheReceiverandremovetheFeed

Elbow(9)fromthemarker.

3. InsertthetabofthecleaningsqueegeeintotheFeedElbowopeningtothebarrelandpushthe

squeegeeintothebarreluntilthetabisaccessibleatthemuzzleendofthebarrel.

4. Pullthesqueegeethroughthebarreltoremovedebris.

5. Repeatifnecessary.

6. ReplacetheFeedElbowbackontothemarker.

7. TightentheFeedElbowThumbNuttosecuretheFeedElbowtothemarkerandreinstallthe

Hopper.

Tomaintainyourmarkeringoodworkingcondition,inspect,clean,andreplaceanydamagedparts.

LubricateasinstructedintheMarker Disassembly/Re-assemblysectionbelow.Thebestvalve

O-ringsaremadeofurethane.UrethaneO-ringsarenotaffectedbyhighgaspressures.Thesemay

bepurchasedfromTippmann®oryourlocalpaintballdealer.UseTippmann®oiltolightlylubricatethe

O-rings,springs,andotherareasindicatedinMarker Disassembly/Re-assemblyinstructions.This

maintainsyourmarkeringoodworkingcondition.

Storage

PuttheTriggerSafetyintheSafeposition.Unloadthemarkerandremovetheair/CO2cylinder.Put

theboltintheforward(uncocked)position.Cleanandoilthemarkersothatitdoesnotrust.Installthe

BarrelSleeve,andstoreyourmarkerinadryarea.

Whenremovingyourmarkeroutofstorage,makesuretheTriggerSafetyisintheSafepositionand

theBarrelSleeveisinstalled.Youshouldre-oiltherearboltO-ringandthefrontboltO-ringbeforeuse.

Marker Disassembly/Re-assembly

Alwaysweareyeprotectionwhenperforminganymarkerdisassemblyorre-assembly.Refertothe

PartsDiagramfortheseinstructions(itemnumbersareinparentheses).Disassemblyinstructionsare

listedhere.Tore-assemble,justdothestepsinthereverseorder.

1. Pullthebolthandleback(seeFigure2)andkeepholdingontoit.Thenpullthetriggerandallow

thebolthandletomoveslowlyforward.Thisuncocksthemarker.

2. ToremovetheBarrel(item54,seeFigure1),simplyunscrewtheBarrelfromtheReceiver,and

toreinstallit,justturnitclockwisetothreaditintotheReceiver.

3. ToremovetheLeft Grip(22)ortheRight Grip(18),removetwo

Screws(14)fromeachgrip.ReassemblebyusingtheScrewsto

fastentheGripstotheReceiver.

4. ToremovetheFeed Elbow(9)fromthereceiver,unscrewthe

Thumbnut(10)fromtherightsideofthereceiver.TheC-Clip(16)

keepstheThumbnutfromcomingloosefromtheFeedElbow.The

FeedElbowhingesdownwardandthebottomtabscomeoutof

Cord Length

Retainer

WARNING

The brass or nickel plated cylinder valve (Figure 4, #1) is intended to be

permanently attached to the air/CO2 cylinder (2).

An air/CO2 cylinder can y off with enough force to cause serious injury or

death if the cylinder (2) unscrews from the cylinder valve (1).

Figure 4: Properly marked

Valve and Cylinder

Figure 5: Misaligned Valve and

Cylinder

Figure 6: The Feed Elbow.

WARNING

EXCEPT WHEN YOUR MARKER IS IN USE, ALWAYS MAKE SURE THAT

THE TRIGGER SAFETY IS IN THE SAFE

POSITION, (WHICH DISABLES THE TRIGGER)

AND THAT THE BARREL SLEEVE IS PROPERLY

INSTALLED (SEE BARREL SLEEVE

INSTALLATION ABOVE).

TO LOCK THE TRIGGER (SAFE POSITION):

PUSH THE TRIGGER SAFETY IN FROM THE MARKER SIDE SHOWN

ABOVE TO THE SAFE POSITION.

TO UNLOCK THE TRIGGER (FIRE POSITION): PUSH THE TRIGGER SAFETY

FROM THE OPPOSITE SIDE OF THE MARKER TO ENABLE FIRING.

TIPPMANN®

2955AdamsCenterRoad,FortWayne,IN46803USA

P)260-749-6022•F)260-749-6619

www.tippmann.com

Figure 2: Pull the Bolt Handle back

until it locks into place.

Figure 3: Velocity Adjustment Screw

Location

Barrel Sleeve

Figure 1: Barrel and O-ring

Carver One Parts List

ITEM

NO. QTY. PT. NO. DESCRIPTION

1 1 TA06053 RightReceiverHalf

2 1 TA06052 LeftReceiverHalf

3 4 98-33 ReceiverDowelPin

4 1 CA-36 SearDowelPin(Black)

5 1 02-35 Sear

6 1 TA02036 SearSpring

7 2 TA02021 ACTLinkageArmGuidePin

8 1 FA-18 BallLatch

9 1 TA06051 FeedElbow

10 1 TA06059 FeedElbowThumbNut

11 1 PL-42C Screw,¼-20x1”SHCS

12 1 PL-42D Nut,¼-20Square(Black)

13 2 98-26 Screw,10-32x¼”BHCS

14 4 CA-02A Screw,6-32x⅜”BHCS

15 8 9-PA Nut,Hex10-32(Black)

16 1 TA06047 LockScrewC-Clip

17 1 98-45 FlatWasherM6(Black)

18 1 TA05004 SplitGrip,Right

19 1 98-01A Bolt,10-32x0.675”

20 2 98-19 ReturnSlideDowelPin

21 1 98-09C GasLine,#4x7⅞”

22 1 TA06003 SplitGrip,Left

23 1 TA06048 Screw,10-32x1.1875”BHCS

24 1 TA06057 USArmyJewel

25 3 TA06015 Screw,10-32x0.840”LHSHCS

26 4 TA09919 Screw,10-32x0.500”LHSHCS

29 1 TA06049 AirSupplyAdapter(ASA)

30 1 CA-08B Nut,10-32

31 1 TA06056 CARVERONENameplate

32 1 CA-14 DriveSpring

33 1 CA-15 GuidePin

34 1 SL2-4 O-ring,FrontBolt

35 1 TA02011 RearBolt

36 1 TA01016 LinkageArm

37 1 98-57 O-ring,EndCap

38 1 98-40 O-ring,Barrel

39 1 CA-27 FrontValveSeat

40 1 PA-28 ValveStemCupSeal

41 1 CA-29 ValveStemCup

42 2 SL2-25 O-ring,ValveSeat

43 1 98-25N ValveBody

44 1 98-56 ValvePlug

45 1 CA-30N ValveStem

46 1 98-32 CompressionSpring

47 1 PA-31A SnapRing

48 1 98-21NR PowerTube

49 1 02-17 FrontBolt

50 1 TA05021 PowerTubePlug

51 1 02-22 VelocitySetScrew

52 1 TA05005 RearBoltPlug

53 1 98-13 RearBoltHandle

54 1 TA06046 Barrel

55 1 TA06060 O-ring,BarrelSleeve

56 1 TA06017 EndCapCover

57 1 TA06006 EndCap

58 2 98-12A O-ring,Valve/RearBolt

59 1 98-36A Trigger

60 1 98-18 TriggerReturnSlide

61 2 98-20 Spring

62 1 98-37N SafetyPin

63 1 98-55 O-ring,Safety(Red)

64 1 FA-07 O-ring,Safety(Black)

PARTS DIAGRAM AND PARTS LIST

theslotsintheRightReceiverHalf(1).TheScrew(11),Flat Washer(17)andNut(12)are

usedtoholdtheHopperintheFeedElbow.Replaceonlyifnecessary.Doallreassemblyinthe

reverseorder.

5. Laythemarkerwiththerightsideontheworkbench.Usetheincludedallenwrenchtoturn

theVelocity Screw(51)allthewayin.SeparatetheReceiver Halves(1and2)byrst

removingthree(longer)Screws(25),andthenfour(shorter)Screws(26)andnallyoneBolt

(19).RetaineightNuts(15)forthesefastenersfromtheRightReceiverHalf.Carefullyliftthe

Left-ReceiverHalftoaccesstheinternalparts.

6. IftheBall Latch(8)needstobereplaced,prytheoldoneoutofthe

RightReceiverHalf.PutthenewBallLatchintotheRightReceiver

Half,orientedasshowninFigure7(circleditem).

7. RemovetheScrew(23)fromtheASA(29).SlidetheASAfromthe

pinintheRightReceiverHalf.BesuretokeeptrackoftheNut(30).

Ifnecessary,youcanunthreadtheASAfromtheGas Line(21).

Useteontapeonthreadsforassembly.

NOTE:Donotremovethegaslinettingunlessitisleakingoryou

needtoreplacethevalve.Ifyoudoremoveit,youwillneedsome

teontapeorpastetoreinstallit.Carefullyhandstartallthreadedparts.Donotovertighten

threadedpartswhenassembling.TofullyremovetheGasLine,unscrewitfromtheValve

Body(43).

The Valve

Disassemblyinstructions:

1. RemovetheEnd Cap Cover(56),andthenremove

theEnd Cap(57).

2. RemovetheGuide Pin(33)andDrive Spring(32).

ThesepartsmustberemovedbeforetheRearBolt

Handlecanberemoved.

3. DisconnecttheLinkage Arm(36)fromtheRear(35)andFront(49)Bolts.

4. SlidetheFrontBoltoffthePower Tube(48)andchecktheO-ring.CleanandoiltheO-ring,or

ifdamaged,replacewithanewone.DothesamewiththeRearBoltO-ring.

5. RemovetheRear Bolt Handle(53)fromtheRear Bolt Plug(52).

6. IfitisnecessarytoremovetheValve,unscrewthetwoValve Lock Bolts(13)fromtheright

sideoftheReceiver.UseawrenchtoslowlyunscrewtheGas Line(21)ttingfromtheValve.

Oncethettingisremoved,theValve(43)slidesoutthebackofthePowerTube.Besureto

setthepartsontheworkbench.Inspectandcleantheexteriorofallassemblies.

NOTE:ChecktheexternalValveO-ring(58)andifdamaged,replacewithanewone.Ifthe

O-ringisdamaged,yourmarkerwillnotfunctioncorrectly.

7. Inspectandlubricatetheseinternaldriveassemblyparts:

• Front Bolt O-ring(34)

• Rear Bolt O-ring(58,seeFigure8)

• Linkage Arm(36)

• Drive Spring(32)andGuide Pin(33)

8. InspectandlubricatetheBarrel O-ring(38)andtheair/CO2cylindervalveO-ringwithafew

dropsofoil.

Reassembly:

1. ReinstalltheValveintothePowerTube.InsertthecleanedandoiledValveintothePowerTube

andaligntheholesoftheValveandPowerTube.Applyteontapeorthreadpasteonthreadsof

theGasLinettingandcarefullyscrewitintotheValve.Snugwithawrench(donotovertighten

andstripthreadedparts).Wipeoffanyexcesspaste.

2. ReinstallthePowerTube/ValveintotheReceiver.AligntheholesofthePowerTubetothoseof

theRightReceiverHalf.ApplyredLoctite™#271sealanttothreadsoftwoValve Lock Bolts

(13)andtighten-donotover-tightenboltsasyoucouldstripthreads.

The Trigger

Disassemblyinstructions:

1. RemovetheTrigger(59)assemblyfromthereceiver.

BesuretoretainthetriggerreturnSpring(61,located

infrontoftheTrigger,andnotshowninFigure9)

2. ToremovetheTrigger Return Slide(60)andthe

Spring(61),youmustrstremovetheupperReturn

Slide Dowel Pin(20)fromtheTriggerassembly.

3. Whenre-assemblingtheTriggerandSear,make

suretheblackSear Dowel Pin(4)isinthelocation

shown(arrowinFigure10).Theblackpinishardened,

anditiscriticalthatitbelocatedinthisposition.

General Troubleshooting

• Issue—Markerrangeistooshort.

Cause—Notenoughgasisenteringthesystem.

Solution—Checkvelocitywithachronograph.

TurnVelocityAdjustertoincreasevelocity,and

recheckwithachronograph.

• Issue—Markerrangeistoolong.

Cause—Toomuchgasisenteringthesystem.

Solution—Checkvelocitywithachronograph.

TurnVelocityAdjustertodecreasevelocity,and

recheckwithachronograph.

• Issue—Gasleakaroundcylindertoreceiverconnection.

Cause—Wornoutordamagedair/CO2cylinderO-ring.

Solution—Replaceair/CO2cylinderO-ring.

• Issue—Minorgasleak.

Cause—WornordamagedvalveseatO-rings.

Solution—ReplacevalveseatO-ringorreturnvalveifitisdefective.

• Issue—Paintballsfalloutofthebarrel.

Cause—WornorbrokenBallLatch(8).

Solution—ReplacetheBallLatch.

Specications

Model.............................................................................................................TIPPMANN®CarverOne™

Caliber................................................................................................................................................ .68

Action........................................................................................... Semi-Automatic(openboltblow-back)

Power...................................................................................................................................... Pneumatic

GasSupply........................................................................... CompressedAir,Nitrogen,orCO2cylinder

HopperCapacity.................................................................................................................188Paintballs

BallFeed.................................................................................................................GravityFeedSystem

FiringRate........................................................................................................... 8paintballspersecond

Trigger.................................................................................................................................... Mechanical

StandardBarrelLength...................................................................................................... 8.5”/21.6cm

Length(withstandardbarrel,nocylinder)...................................................................... 18.75”/47.6cm

EffectiveRange............................................................................................... 150+feet/45.72+meters

Weight(withoutcylinder)..........................................................................................3.245lbs/1.472kg

Finish......................................................................PowderCoatedReceiverandASA,AnodizedBarrel

Velocity—Alwaysmeasureyourmarker’svelocitybeforeplayingpaintballandnevershootat

velocitiesinexcessof300feet/91.44meterspersecond(seeVelocityAdjustmentinstructions).

Warranty and Repair Information

TIPPMANNSPORTS,LLC(“Tippmann”)isdedicatedtoqualitypaintballproductsandoutstanding

service.IntheunlikelyeventofaproblemwiththisTippmannpaintballmarker(“Marker”)and/or

Tippmannaccessories(“Accessories”),Tippmann’scustomerservicepersonnelareavailabletoassist

you.Forcustomerserviceand/orotherinformation,pleasecontact:

 TippmannSports,LLC

 2955AdamsCenterRoad

 FortWayne,IN46803

 www.tippmann.com

 1-800-533-4831

Warranty Registration

ToactivatetheMarker’sLimitedWarranty,youmustregistertheMarkerwithinthirty(30)daysofthe

dateoforiginalretailsalebyregisteringonlineatwww.tippmann.com.

TheLimitedWarrantyforTippmannAccessoriesdoesnotrequireactivationorregistration;by

registeringtheMarker,youactivatethewarrantyfortheAccessories.

Limited Warranty

Tippmannwarrantstotheoriginalpurchaserthatitwillmakeanyrepairsorreplacementsnecessary

tocorrectdefectsinmaterialorworkmanship,atnochargetoyou,fortheMarkerforaperiodofone

(1)yearfromthedateoforiginalretailsale.Further,Tippmannwarrantstotheoriginalpurchaserthat

itwillmakeanyrepairsorreplacementsnecessarytocorrectdefectsinmaterialorworkmanship,at

nochargetoyou,forTippmannAccessoriesforaperiodofninety(90)daysfromthedateoforiginal

retailsale.AllTippmannasksisthatyouproperlymaintainandcarefortheMarkerandAccessories

(collectively,the“Product”)andthatyouhavewarrantyrepairsperformedbyTippmannoraTippmann

CertiedTechCenter.

ThisLimitedWarrantyisnon-transferable,anditdoesnotcoverdamageordefectstotheProduct

causedby(a)impropermaintenance;(b)alterationormodication;(c)unauthorizedrepair;(d)

accident;(e)abuseormisuse;(f)neglectornegligence;and/or(g)normalwearandtear.

Tippmanndoesnotauthorizeanypersonorrepresentativetoassumeorgrantanyotherwarranty

obligationwiththesaleofthisProduct.

THISISTHEONLYEXPRESSWARRANTYGIVENWITHTHEPURCHASEOFTHISPRODUCT;

ANYANDALLOTHEREXPRESSWARRANTIESAREDISCLAIMED.THEIMPLIEDWARRANTIES

OFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSEARELIMITEDTOTHE

APPLICABLELIMITEDWARRANTYPERIODSETFORTHHEREIN,ANDNOWARRANTIES,

WHETHEREXPRESSORIMPLIED,SHALLAPPLYAFTEREXPIRATIONOFSUCHPERIOD.

Somestatesandnationsdonotallowlimitationsonthedurationofimpliedwarranties,sotheabove

limitationmaynotapplytoyou.

ThesoleandexclusiveliabilityofTippmannand/oritsauthorizeddealersunderthisLimitedWarranty

shallbefortherepairorreplacementofanypartorassemblydeterminedtobedefectiveinmaterial

orworkmanship.TIPPMANNSHALLNOTBELIABLEFOR,ANDYOUEXPRESSLYDISCLAIM,

ANYDIRECT,INDIRECT,CONSEQUENTIALORINCIDENTALDAMAGES(COLLECTIVELY,

“DAMAGES”)ARISINGOUTOFTHESALEORUSEOF,ORYOURINABILITYTOUSE,THE

PRODUCT.NOPAYMENTOROTHERCOMPENSATIONWILLBEMADEFORDAMAGES,

INCLUDINGINJURYTOPERSONORPROPERTYORLOSSOFREVENUEWHICHMIGHTBE

PAID,INCURREDORSUSTAINEDBYREASONOFTHEFAILUREOFANYPARTORASSEMBLY

OFTHEPRODUCT.

Somestatesandnationsdonotallowtheexclusionorlimitationofincidentalorconsequential

damages,sotheabovelimitationorexclusionmaynotapplytoyou.Thiswarrantygivesyouspecic

legalrights,andyoumayalsohaveotherrightsthatmayvaryfromstatetostateornationtonation.

Warranty and Non-Warranty Repairs

WhenshippingtheProducttoTippmannforwarrantyornon-warrantyrepair:

1. IfyouhaveaftermarketpartsonyourMarker,pleasetesttheMarkerwithoriginalstockparts

beforereturningtheMarkerforserviceorrepair.

2. Alwaysunloadandremovetheair/CO2cylinderfromtheMarker.Donotshiptheair/CO2

cylinderifitisnotcompletelyempty.

3. ShiptheProducttotheTippmannaddressidentiedabove.

4. Youmustpre-paypostageanddeliverycharges.

5. ProvidethedateofpurchasefortheProduct.

6. Brieydescribetherepairrequested.

7. Includeyourname,returnaddressandatelephonenumberwhereyoucanbereachedduring

normalbusinesshours,ifpossible.

Tippmannmakeseveryefforttocompleteitsrepairworkwithintwenty-four(24)hoursofreceipt.

TippmannwillreturntheProducttoyouviaregulargroundUPS.Ifyouwishtohaveitreturnedusing

afasterservice,youcanrequestNEXTDAYAIRUPSORSECONDDAYAIRUPS,butyouwillbe

chargedforthisserviceandmustincludeyourcreditcardnumberwiththeexpirationdate.Yourcredit

cardwillbechargedthedifferenceinadditionalcostoverregulargroundshippingservice.

Figure 8: The Rear Bolt Assembly.

Figure 9: The Trigger is pulled from the

right receiver half.

59 61

Figure 10: The black pin is hardened

and must be installed in the

position as shown.

TP04606 01/10Revised 01/26/10

Figure 7: Ball Latch properly

installed into the

right receiver half.

Tippmann CARVER ONE Owner's manual

Tippmann CARVER ONE Owner's manual

Tippmann CARVER ONE Owner's manual

Related papers

Other documents