Outdoor Mist
Tripod Mist Stand
INSTRUCTIONS:
IMPORTANT: READ ALL OF THE INSTRUCTIONS AND REVIEW
ASSEMBLY DIAGRAMS BEFORE BEGINNING ASSEMBLY.
ASSEMBLY:
1. Wrap all of the threads of the Mist Bar with Teflon Tape to prevent
leaking, before screwing into the Telescoping Pole.
2. Screw Mist Bar into the top of the Telescoping Pole as shown below.
3. Hold the Telescoping Pole in one hand in front of you and hold
the Tripod Base (with the legs pulled in as shown in the picture below)
in front of you with the other hand. The coil spring will stay inside of
the tube as you screw the Telescoping Pole onto the threaded top of
the Tripod Base.
4. Extend the legs and tighten the knob to hold them securely in place.
5. Remove the 5 Brass and Stainless Steel Mist Nozzles from the spray
bar.
6. Attach the Brass Slip-Lok Hose Adapter to the end of the tan tubing
coming out of the bottom of the mist stand.
7. Then attach the Brass Slip-Lok Hose Adapter to the end of a standard
garden hose. The other end of the garden hose will be attached to
your water spigot.
8. Turn on the water and flush out the mist stand to remove any dirt or
debris which may clog the nozzles.
9. Turn off the water and replace the mist nozzles into the Mist Bar.
TIGHTEN ONLY HAND TIGHT.
10. Loosen the black ring in the middle of the Telescoping Pole and adjust
to your desired height.
11. Tighten the black ring to keep the Telescoping Pole at the desired
height selected.
12. When you reduce the height, gently pull on the tubing at the base
of the mist stand to keep it from getting tangled or wrapped around
the Tripod’s legs.
13. Turn on the water and enjoy!
IF USING WITH THE 160 PSI BOOSTER PUMP
(Orbit
®
|Arizona Mist
®
Model #92100):
In order to attach the 160 psi Booster Pump to the Mist Stand, you will
need to purchase a couple of items:
A. 20 ft. Length of 3/8 in. tubing (Orbit
®
|Arizona Mist
®
Model #92228)
B. A PVC tubing cutter (scissors will not work)
C. 160 psi Booster Pump (Orbit
®
|Arizona Mist
®
Model #92100)
Instructions:
1. The 160 psi Booster Pump will be placed between the water spigot and
the Brass Slip-Lok Hose Adapter, so the boosted pressure enters the
mist stand.
2. Remove the Brass Slip-Lok Hose Adapter from the end of the tan
tubing. This is done by pulling back on the Slip-Lok ring and pulling the
tubing out.
3. A fresh straight end will need to be cut on the tubing, to ensure proper
fit into the outlet of the 160 psi Booster Pump. This can be done with a
pair of tubing cutters.
4. The new straight end is then inserted into the Slip-Lok fitting marked
OUTLET on the pump.
5. Take the 20 ft. length of 3/8 inch tubing and insert one end into the
Slip-Lok fitting marked INLET on the pump, pushing until it goes in no
further. Give a tug backwards to ensure it is inserted fully.
6. Cut the tubing to the desired length.
7. Attach the Brass Slip-Lok Hose Adapter in the same fashion as
described in #5 above and shown in the illustration.
CAUTIONS:
1. The use of an Inline Calcium Inhibitor Filter (Orbit
®
|Arizona Mist
®
Model #10109) is strongly recommended to prevent clogging. If the
filter is used with the 160 psi Booster Pump, regular changing is
required. A clogged filter will shut off the water flow to the pump,
which will render the motor inoperable and non-repairable.
2. To prevent any injuries or damage to the Mist Stand, do not move the
Mist Stand by pulling on the tubing or hose at the base. Always grasp
the mist stand on the Telescoping Pole, pick it up and move it to the
desired location.
3. To prevent any injuries, ensure the Mist Stand is placed out of high
traffic areas. This will prevent anyone from tripping over the Tripod
Base or sustaining eye or head injury from the Mist Bar.
4. Minimum required water pressure (inlet) is 45 psi. If using the 160 psi
Booster Pump with this Mist Stand and the water pressure is greater
than 45 psi, it is recommended to use a pressure reducer from the
water spigot to the inlet on the Booster Pump.
5. Maximum water pressure (outlet) is 160 psi.
6. This Mist Stand is For Outdoor Use with Cold Water Only.
Apply Teflon
Tape Here
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no: 5
date: 01.22.10
des: MZ spck: MZ
job no: N/A
client: Orbit
sku: 10717
upc: NA
file name:
10717-24 rA.indd
software: InDesign CS3
colors
additional instructions:
· Font sizes cannot be smaller than 7 pt.
· 517944
·
color
non printing
PMS
????
PMS
????
color
non printing
PMS
????
Registration
BLACK
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 11" h: 8.5"
finished: w: 11" d: 0" h: 8.5"
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Register your product online
at www.orbitonline.com
Orbit® Irrigation Products Inc.
845 North Overland Road
North Salt Lake, Utah 84054 USA
http://www.orbitonline.com
800-488-6156
801-299-5555
PN 10717-24 Rev A
1
2
Orbit 92100 Installation guide
Aero Mist 50027-10 Installation guide
Arctic Cove MBP160 Installation guide
CITC FX Water Pump 100068 User manual
Ryobi PMP01K Owner's manual
Polaris PB4-60 Owner's manual
Arctic Cove MBF0181 User manual
Polaris PB4SQ Owner's manual
Kobalt KMF 1024B-03 User manual
