Hampton Bay EC751WH User guide

1

INSTRUCTION MANUAL

8' Track Section

Black Finish

White Finish

Home Depot SKU 675-193(UPC008938275187) BK

Home Depot SKU 555-235(UPC008938275101) WH

2

Thank you for purchasing this Hampton Bay interior track section. This product has been

manufactured with the highest standards of safety and quality.

FEATURES:

1. This 8ft. track section is designed for mounting to ceiling or walls.

2. All Hampton Bay EC series track adapters and track heads can be installed into the

track section and can move to any position along the track section.

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our Customer Service Team at 1-

877-527-0313 or visit www.homedepot.com. Please reference SKU 675-193, UPC

008938275187, or SKU 555-235, UPC 008938275101.

IMPORTANT SAFETY INSTRUCTIONS

When installing or using this track system, basic safety precautions should always be

followed including the following:

1. Read all of these installation instructions before installing the track system.”

2. Save these instructions and refer to them when additions to or changes in the track

configuration are made.

3. Do not install this lighting system in a damp or wet location.

4. Before energizing make sure that the lighting system is clear of all material which

could cause a direct short and check all electrical connections to make sure they are

tight.

5. Do not install any part of this system (TRACK) less than 7 feet (2.2m) above floor.

6. Do not install any lamps closer than 6 inches (15.25cm) from any curtain or similar

combustible material.

7. For installation with EC series track only.

8. This track system is not intended for the use with a power supply cord or convenience

receptacle adaptor.

9. This track system is to be supplied by a single branch 120 volt 60Hz circuit.

10. The track is not intended to be pendant mounted such as by a stem or cable.

11. The mounting screws are to be mounted along the track in the keyhole slots provided.

12. Disconnect electrical power before adding to or changing the configuration of the

track.

13. Do not attempt to energize anything other than lighting track fixtures on the track. To

reduce the risk of fire and electrical shock, do not attempt to connect power tools,

extension cords, appliances, and the like to the track.

Note: The important safeguards and instructions appearing in this manual are not meant to

cover all possible conditions and situations that may occur. It must be understood that

common sense, caution and care are factors that cannot be built into any product. These

factors must be supplied by the person(s) caring for, installing and operating the fixture. If

at any time you are uncomfortable or are unsure of what to do, please contact a qualified

licensed electrician for further assistance.

SAVE THESE INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included):

Ladder Safety goggles Gloves Flathead Phillipshead Drill 1/4 in or 5/8 in

screwdriver screwdriver Drill bits

3

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

(1) 96in. Linear Track (3) Toggle bolts (3) Tapped Screws (3) anchors

FIELD CUTTING TRACK TO SPECIAL LENGTHS (OPTIONAL):

Note: Cutting should be done preferably from the dead end of the track.

1. Remove dead end fitting and pull copper bus bars and insulators flush or even with

one end of the track.

2. With a hacksaw, cut the flush end (the side with insulators and bus bars even to end) to

desired length. Be sure to allow 1/8

th

in. for dead end fitting which must be reinstalled

to the track end.

3. Remove all burrs from the track, insulators and copper bus bars.

4. Push copper bus bars back into the insulators 3/8

th

in. from the end of the insulators.

Note: After you complete step 4, bus bar insulators should be a minimum of 3/8

th

in. and a

maximum of ½ in. from each end of the insulator. If this is not the case, make

appropriate modifications.

5. Reinstall the dead end and/or appropriate feed connector and tighten the screw.

CAUTION: After track has been field cut, make certain that each length of track that is 4

feet (1.22m) or less in length has one mounting opening spaced a maximum of 6 in.

(150mm) from each track end section. A single section of track that is greater than 4 feet

(1.22m) in length must have mounting openings a maximum of 12 in (300 mm). from each

end of the track with additional openings a minimum of every 4 feet (1.22m) long the

length of the track section. Additional openings every 4 feet (1.22m) along the track

section may be added as needed.

IF ADDITIONAL MOUNTING HOLES ARE NEEDED (OPTIONAL):

1. Locate desired mounting hole(s) on the inside of the track section along the center line.

2. Using 3/16

th

in. diameter drill bit, drill a hole through the track channel.

CAUTION: Take care that you do not damage the bus bar insulators during the drilling

operation. If you accidentally damage any insulators, discard the track section. To

prevent the risk of fire, or injury to person(s), DO NOT ATTEMPT TO USE IT IN

THE INSTALLATION.

3. Remove all burrs and install track as described above.

REDRILL

MOUNTING

HOLE(S) IF

N

ECESSARY

N

EW CUT MUST BE AT AN EXACT

RIGHT ANGLE

(

90°

)

TO REMOVE DEAD

END FITTING.

LOOSEN SCREW

AND SLIDE FITTING

OUT.

4

INSTALLATION INSTRUCTIONS

(AS SHOWN IN DIAGRAM):

INSTALLATION OF TRACK/CONNECTOR ASSEMBLY:

1. Determine which connector will be used to power track and attach.

2. Place track power feed connector assembly at desired location on ceiling, noting

location of electrical supply. Mark the ceiling through the holes in track and remove

track.

3. For toggle bolt installation, drill a 5/8in. hole at each mark on ceiling, insert bolts

through the track and thread toggles 1/2in. onto bolts.

4. Place track/connector assembly against ceiling and insert toggles into holes until the

spring open. Tighten bolts.

5. To connect two tracks, loosen set screws on straight connector, align grounds and insert

into track. Tighten set screws.

TROUBLE SHOOTING:

Problem Possible Cause Corrective Action

1. Light bulb is burned

out.

1. Replace light bulb.

2. Power is off. 2. Make sure power supply is

on.

3. Faulty connection of

fixture to track or wire

connections.

3. Check connection of fixture

to track. Check wiring.

Light Bulb will not

illuminate.

4. Faulty switch. 4. Test or replace switch.

Fuse blows or circuit

breaker trips when light

bulb is illuminated.

Crossed wires or power

wire is grounding out.

Check wire connections.

Ceiling

Track

Dead end cap

Toggle bolt assy

5

PRODUCT MAINTENANCE:

1. Turn off power to the light fixture.

2. To clean the fixture, first disconnect power to the fixture by turning off the circuit

breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never use a solvent) to wipe the inside

glass and interior surface of the fixture. Allow the fixture to dry completely before

power is restored.

CAUTION: Do not use chemical solvents or harsh abrasives to clean fixture as damage

to the fixture or various components may occur remedying the fixture inoperable.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of five (5) years from date of purchase. This warranty applies

only to the original consumer purchaser and only to products used in normal use and

service. If this product is found to be defective, the manufacturer’s only obligation, and

your exclusive remedy, is the repair or replacement of the product at the manufacturer’s

discretion, provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling. This warranty shall not apply

to any product that is found to have been improperly installed, set-up, or used in any way

not in accordance with the instructions supplied with the product. This warranty shall not

apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alteration, or faulty installation, or any other failure not relating to faulty material or

workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear. The

manufacturer does not warrant and specially disclaims any warranty, whether express or

implied, of fitness for a particular purpose, other than the warranty contained herein. The

manufacturer specifically disclaims any liability and shall not be liable for any

consequential or incidental loss or damage, including but not limited to any labor/expense

costs involved in the replacement or repair of said product.

6

MANUEL D’INSTRUCTIONS

Section de rail 2,44 m (8 pi)

Fini noir

Fini blanc

Home Depot UGS 675-193 (CUP 008938275187) Noir

Home Depot UGS 555-235 (CUP 008938275101) Blanc

Page is loading ...

Hampton Bay EC751WH User guide

Hampton Bay EC751WH User guide

in other languages

Related papers

Other documents