RCA Cordless Telephone 25413 User manual

900 MHz

Cordless Handset

with Caller ID

User’s Guide

This accessory handset is only for use

with Model 25413, 25414, or 25415

base units.

Please read this manual

before operating this

product for the ﬁrst time.

Model H5400

2

Equipment Approval Information

Your telephone equipment is approved for connection to the

Public Switched Telephone Network and is in compliance with

parts 15 and 68, FCC Rules and Regulations and the Technical

Requirements for Telephone Terminal Equipment published by

ACTA.

1 Notiﬁcation to the Local Telephone Company

On the bottom of this equipment is a label indicating, among

other information, the US number and Ringer Equivalence

Number (REN) for the equipment. You must, upon request,

provide this information to your telephone company.

The REN is useful in determining the number of devices you

may connect to your telephone line and still have all of

these devices ring when your telephone number is called. In

most (but not all) areas, the sum of the RENs of all devices

connected to one line should not exceed 5. To be certain

of the number of devices you may connect to your line

as determined by the REN, you should contact your local

telephone company.

A plug and jack used to connect this equipment to the

premises wiring and telephone network must comply with

the applicable FCC Part 68 rules and requirements adopted

by the ACTA. A compliant telephone cord and modular plug

is provided with this product. It is designed to be connected

to a compatible modular jack that is also compliant. See

installation instructions for details.

Notes

• This equipment may not be used on coin service provided

by the telephone company.

• Party lines are subject to state tariffs, and therefore, you

may not be able to use your own telephone equipment if

you are on a party line. Check with your local telephone

company.

• Notice must be given to the telephone company upon

permanent disconnection of your telephone from your line.

• If your home has specially wired alarm equipment

connected to the telephone line, ensure the installation of

this product does not disable your alarm equipment. If you

have questions about what will disable alarm equipment,

consult your telephone company or a qualiﬁed installer.

US Number is located on the cabinet bottom

REN number is located on the cabinet bottom

Important Information

3

2 Rights of the Telephone Company

Should your equipment cause trouble on your line which may

harm the telephone network, the telephone company shall,

where practicable, notify you that temporary discontinuance

of service may be required. Where prior notice is not

practicable and the circumstances warrant such action, the

telephone company may temporarily discontinue service

immediately. In case of such temporary discontinuance, the

telephone company must: (1) promptly notify you of such

temporary discontinuance; (2) afford you the opportunity to

correct the situation; and (3) inform you of your right to bring

a complaint to the Commission pursuant to procedures set

forth in Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its

communications facilities, equipment, operations or

procedures where such action is required in the operation

of its business and not inconsistent with FCC Rules and

Regulations. If these changes are expected to affect the use

or performance of your telephone equipment, the telephone

company must give you adequate notice, in writing, to allow

you to maintain uninterrupted service.

Interference Information

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference; and (2) This device must accept

any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

Privacy of Communications may not be ensured when using this

product.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the

antenna for radio or television that is “receiving” the

interference).

• Reorient or relocate and increase the separation between the

telecommunications equipment and receiving antenna.

Important Information

4

• Connect the telecommunications equipment into an outlet on

a circuit different from that to which the receiving antenna is

connected.

If these measures do not eliminate the interference, please

consult your dealer or an experienced radio/television technician

for additional suggestions. Also, the Federal Communications

Commission has prepared a helpful booklet, “How To Identify

and Resolve Radio/TV Interference Problems.” This booklet is

available from the U.S. Government Printing Ofﬁce, Washington,

D.C. 20402. Please specify stock number 004-000-00345-4 when

ordering copies.

Notice: The changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user’s

authority to operate the equipment.

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid

Compatibility.

Licensing

Licensed under US Patent 6,427,009.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum

distance of 20 centimeters between the radiator and your

body. This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.”

For body worn operation, this phone has been tested and

meets the FCC RF exposure guidelines when used with the

belt clip supplied with this product. Use of other accessories

may not ensure compliance with FCC RF exposure guidelines.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

CAUTION:

Important Information

5

Table of Contents

Important InformatIon .................................................... 2

EquIpmEnt approval InformatIon ........................................... 2

IntErfErEncE InformatIon ....................................................... 3

HEarIng aId compatIbIlIty (Hac) .......................................... 4

lIcEnsIng .............................................................................. 4

fcc rf radIatIon ExposurE statEmEnt .................................. 4

IntroductIon ................................................................... 7

connEctIons and sEtup .................................................... 8

bEforE your bEgIn ................................................................ 8

Parts CheCklist ..............................................................................8

Digital seCurity system.................................................................8

imPortant installation information .............................................8

imPortant installation guiDelines ................................................8

installing the hanDset Battery ....................................................9

ConneCting the aC (eleCtriCal) Power .......................................10

ConneCting the rf moDule ..........................................................10

registering the hanDset ...............................................................10

HandsEt layout ..................................................................... 11

tElEpHonE sEtup .................................................................... 11

language ........................................................................................11

tElEpHonE opEratIon ....................................................... 12

loCal area CoDe ...........................................................................12

regional area CoDe ......................................................................12

Clear all memories ......................................................................12

set time ..........................................................................................12

registration (re-registration).....................................................12

basIc opEratIon .................................................................... 13

answering a Call ..........................................................................13

making a Call ...............................................................................13

reDial ............................................................................................13

Volume aDjust ...............................................................................13

holD ............................................................................................14

transfer .........................................................................................14

PriVaCy ...........................................................................................14

flash ............................................................................................14

manual Channel seleCtion ..........................................................14

Call timer ......................................................................................14

ringer on/off switCh ..................................................................14

out of range .................................................................................15

Battery low ...................................................................................15

Paging all extension from the CorDless hanDset .....................15

Paging the CorDless hanDset .......................................................15

IntErcom opEratIon ............................................................... 15

answering an interCom Call .......................................................15

6

Table of Contents

reCeiVing an inComing telePhone Call During an interCom

Call .....................................................................................15

using interCom with a telePhone Call ........................................15

Two-way InTercom calls ............................................................16

Three-way InTercom calls ..........................................................16

making an interCom Call with other extensions ......................16

mEmory ................................................................................ 16

storing a name anD numBer in memory ....................................16

storing a reDial numBer..............................................................17

inserting a Pause in the Dialing sequenCe ..................................17

reViewing, Changing or Deleting storeD names/numBers ........18

Dialing a storeD numBer .............................................................18

Chain Dialing from memory ........................................................18

callEr Id (cId) .................................................................... 19

reCeiVing anD storing CiD reCorDs ............................................19

reViewing Call reCorDs ................................................................20

transferring CiD reCorDs to memory........................................20

Dialing a Caller iD numBer ........................................................21

Deleting the Current Caller iD reCorD ......................................21

Deleting all Caller iD reCorDs ...................................................22

Caller iD errors ...........................................................................22

Call waiting Caller iD ................................................................22

cHangIng tHE battEry ............................................................ 22

Battery safety PreCautions ..........................................................23

HEadsEt and bElt clIp opEratIon ........................................... 23

ConneCting an oPtional heaDset to the hanDset .......................23

ConneCting the Belt CliP ..............................................................23

troublEsHootIng tIps ....................................................... 23

dIsplay mEssagEs .................................................................. 24

HandsEt sound sIgnals ......................................................... 25

troublEsHootIng guIdE .......................................................... 25

Telephone soluTIons .....................................................................25

caller ID soluTIons .....................................................................26

BaTTery soluTIons .........................................................................26

gEnEral product carE ........................................................... 27

causEs of poor rEcEptIon ...................................................... 27

sErvIcE ................................................................................. 27

otHEr InformatIon .......................................................... 27

lImItEd Warranty ................................................................. 28

IndEx .............................................................................. 30

accEssorIEs InformatIon .................................................. 32

7

CAUTION: When using telephone equipment, there

are basic safety instructions that should always

be followed. Refer to the IMPORTANT SAFETY

INSTRUCTIONS provided with this product and save

them for future reference.

Congratulations on purchasing this RCA telephone. This

system operates in the 900 MHz frequency range. This

accessory handset will expand the phone systems for

Models 25413/25414/25415 to cordless when the RF

module (packed with this cordless handset) is plugged into

the back of the base unit.

NOTE: For use only with model 25413XXX-A, 25414XXX-A

and 25415XXX-A identiﬁed also by E211520 only.

Features:

• Call Waiting and Caller ID Compatible

• Tone Dialing

• Intercom

• Call Transfer

This telephone has been designed to be simple to use,

however, you can reach its full potential more quickly by

taking a few minutes to read this instruction book. This

telephone is a multifunction product for use with Call

Waiting and Caller ID services available from your local

telephone company.

Your Caller ID Call Waiting phone allows you to:

• View the name and telephone number of a caller while

you are on the phone (Call Waiting Caller ID).

• Identify callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 40 Caller ID messages sequentially in each

handset.

• Know who called while you are on the line or when you

were away.

• Screen unwanted calls, eliminate harassment from

annoying calls, or to get prepared before answering a

call.

IMPORTANT: In order to use all of the features of this

telephone, you must subscribe to two separate services

available from your local telephone company: the

standard Name/Number Caller ID Service to know who

is calling when the phone rings and Caller ID with Call

Waiting Service to know who is calling while you are on

the phone.

Introduction

8

Before Your Begin

Parts Checklist

Make sure your package includes the items shown here.

Connections and Setup

9

• Avoid areas of excessive moisture or extremely low

temperature.

• Avoid dusty locations.

• Avoid other cordless telephones or personal computers.

INSTALLATION NOTE: Certain other communications

devices may also use the 900 MHz frequency for

communication, and, if not properly set, these devices

may interfere with each other and/or your new

telephone. If you are concerned with interference, please

refer to the owner’s manual for these devices on how to

properly set channels to avoid interference.

Installing the Handset Battery

NOTE: You must connect the handset battery before use.

CAUTION: To reduce the risk of ﬁre or personal injury,

use only the Thomson Inc. approved Nickel-metal

Hydride (Ni-MH) battery model 5-2650 that is

compatible with this unit.

1. Locate battery and battery door which are packaged

together inside a plastic bag and are separate from the

handset.

2. Locate the battery compartment on the back of the

handset.

3. Plug the battery pack cord into the jack inside the

compartment.

NOTE: To ensure proper battery installation, the connector

is keyed and can be inserted only one way.

Connections and Setup

BLACK WIRE

RED WIRE

BA TTER Y

PRESS DOWN

FIRM LY

10

Connecting the AC (Electrical) Power

Plug the power adaptor cord into the power jack on the

back of the base and the other end into an electrical

outlet. The charge/in use indicator turns on to indicate the

battery is charging when the handset is on the cradle.

Allow the phone to charge for 12 hours prior to ﬁrst

use. If you do not properly charge the phone, battery

performance is compromised.

CAUTION: Use only the 5-2652 power adaptor that came

with this unit. Using other power adaptors may damage

the unit.

Connecting the RF Module

Insert the RF module into the back of the base unit until

it snaps into place. The display wi l show when the RF

module is connected properly.

Registering the Handset

NOTE: Handset must be registered to the base to be

operational.

Once a handset is registered it can use the base phone’s

connection. A cordless handset will not operate until it is

registered to a base. During the registration process, keep

the handset near the base.

NOTE : At initial power up, display will show “PLEASE

REGISTER”. To continue registration from this point,

proceed to step #4.

1. On the handset, press the MENU button once, and then

press the 4 button until REGISTRATION shows on the

display.

2. Press the SELECT/SAVE button or the STORE button to

select Registration mode.

3. Press the 3 or 4 button on the handset to select YES.

4. Press SELECT/SAVE to conﬁrm. The display shows

REGISTER....

5. On the base, press and hold the PAGE button for 3

seconds. If the registration is successful, the handset

will emit a long beep.

6. If the registration fails, FAIL! TRY AGAIN will show on

the handset display. Please repeat the above steps.

Connections and Setup

11

Handset Layout

12

Local Area Code

1. Press the MENU button once, then press the 4 button

until AREA CODE is displayed.

2. Press the SELECT/SAVE or STORE button to select.

3. Use the number pad to enter your three digit area code.

The default is “---”.

4. Press the SELECT/SAVE button again to store the setting.

Regional Area Code

You can enter six regional codes.

1. Press the MENU button once, then press the 4 button

until REGIONAL CODE is displayed.

2. Press the SELECT/SAVE or STORE button to select.

3. Use the number pad to enter your three digit regional

code. If you make an error while entering a code, press

the DELETE/CHANNEL button to delete the character.

4. When all digits are entered into a code, the cursor will

automatically go to the next one. You may also press

the 3 or 4 button to move through the six codes.

5. When you have ﬁnished entering the codes, press the

SELECT/SAVE button again to store the setting(s).

Clear All Memories

1. Press the MENU button once, then press the 4 button

until

CLEAR ALL MEM is displayed.

2. Press the SELECT/SAVE or STORE button to select.

3. Press the 3 or 4 button on the handset to select YES.

4. Press the SELECT/SAVE button again to clear all the

records in the phonebook memory.

Set Time

The time cannot be set manually in the handset,

only at the base. Any update to the base time will be

automatically sent to the handset.

Registration (Re-Registration)

Registration links the cordless handset to the base which

allows the handset to use the base’s phone connection. A

cordless handset will not operate until it is registered to

the base. During the registration process, keep the handset

near the base. If your handset becomes unregistered, it

may be necessary for you to re-register to the base. To do

so follow the steps below.

1. Press the MENU button once, and then press 4 button

until REGISTRATION is displayed.

Telephone Operation

13

2. Press the SELECT/SAVE or STORE button to select.

3. Press the 3 or 4 button on the handset to select YES.

4. Press SELECT/SAVE to conﬁrm. The display will show

REGISTER....

5. On the base, press and hold the PAGE button for 3

seconds. If the registration is successful, the handset

will emit a long beep.

6. If the registration fails, FAIL! TRY AGAIN will show on

the display. Please repeat the above steps.

Basic Operation

Answering a Call

1. Press the TALK button on the handset. (The base

displays CORDLESS H/S IN USE).

2. When ﬁnished, press the TALK button or replace the

handset in the charge cradle, to hang up.

Making a Call

1. Press the TALK button to access an available line

automatically,

OR

If you want to select a desired line, press LINE button

plus a number button (1-4) to select the desired line.

2. Wait for a dial tone then dial the desired number.

3. When ﬁnished, press the TALK button or replace the

handset in the charge cradle, to hang up.

NOTE: If the line you selected is occupied by other users,

the message “LINE IN USE” will be shown. You can press

the SELECT/SAVE button to conﬁrm selection of this line.

If you want to select another line, press the LINE button

plus the number button again.

Redial

To quickly redial the last number you entered (up to 32

digits):

1. Press TALK button.

2. Press the FORMAT/REDIAL button.

Volume Adjust

Adjust the receiver volume by pressing the Volume Up/

Down button (located at the side of the handset) when

you are in talk mode. There are four volume levels, and

each press of the Volume Up/Down button adjusts the

receiver volume by one level.

Telephone Operation

14

Hold

Press the HOLD button to put a call on hold.

To take a call off hold, press the HOLD button again.

To switch a call on hold from the base to the cordless

handset, press the HOLD button on the cordless handset.

Transfer

You can transfer the call to another extension.

1. Press the TRANSFER button when it is in TALK mode.

2. Key in the extension ID number you want to transfer to.

3. The desired extension will ring, and your handset will

go back to standby mode.

Privacy

When you are using the phone, if you want to secure the

line, press the PRIVACY button. Then, the line you are

using cannot be picked up by another extension in the

system.

Flash

Use the FLASH/EXIT button on the handset to activate

custom calling services such as call waiting or call transfer,

which are available through your local phone company.

TIP: Don’t use the TALK button to activate custom calling

service such as call waiting, or you’ll hang up the phone.

Manual Channel Selection

While talking, you might need to manually change the

channel in order to reduce static caused by baby monitors,

garage door openers, or other cordless phones. Press

and release the DELETE/CHANNEL button on the cordless

handset to advance to the next clear channel.

Call Timer

After you press TALK or LINE plus number button to select

the line on the cordless handset, the built-in call timer

shows in the display and begins counting the length of

time of the call.

Ringer On/Off Switch

Use the two-position switch on the cordless handset to

turn the ringer volume ON or OFF.

Telephone Operation

15

Out of Range

If the handset is too far from the base (out of range) you

may experience static or noise. Move closer to the base

or handset will automatically hang up if it is kept out of

range for 30 seconds.

Battery Low

If the handset battery is low, the unit will emit the alert

tone and show BATTERY LOW in the display to remind you

that the battery needs charging. If the battery voltage is

very low, the handset will automatically shut down. Place

handset in the charge cradle to recharge battery.

Paging All Extension from the Cordless Handset

In the standby mode, press the INT button and then press

zero (0) button twice to activate page all extensions

function.

Paging the Cordless Handset

This feature helps you locate a misplaced handset.

Press the PAGE button once on the base, then press

number 0 button. The cordless handset will beep

continuously (if it is not out of range) for 2 minutes or

until you press any button on the handset.

NOTE: You may still page the cordless handset even if the

ringer is turned off.

Intercom Operation

Answering an Intercom Call

1. Press the INTERCOM button or TALK button.

2. When ﬁnished, press the INTERCOM button or TALK

button again.

Receiving an Incoming Telephone Call During

an Intercom Call

During an intercom call, if you receive a telephone call,

you will hear an alert tone. To answer the incoming call,

press the HOLD button to place your intercom call on hold

or press TALK or INT button to drop the intercom call, then

press TALK to answer the telephone call.

Using Intercom with a Telephone Call

During a telephone call, you can use the intercom

function to page another extension unit and set up a

private (2-way) intercom conversation with another user

while the telephone call is placed on hold. Or, you can

create a 3-way conversation between the telephone caller,

the cordless handset and other extensions.

Telephone Operation

16

Two-Way Intercom Calls

1. To make an intercom call, ﬁrst press the HOLD button

to place the external call on hold. Then, press the INT

button followed by the extension ID number.

2. To answer the intercom call, press HOLD to place the

current call on hold. Then press INT or TALK button

to answer the intercom call. When ﬁnished, press INT

or TALK button to end the intercom call. Press HOLD

button to retrieve the external caller.

Three-Way Intercom Calls

1. Press HOLD button to hold the current line.

2. Press INT button, followed by the extension ID number.

3. Wait for the reply of extension you selected.

4. Once the extension replies, press the CONF button to

set up three-way conference.

5. When ﬁnished, press the TALK button once.

Making an Intercom Call with Other Extensions

1. Make sure the phone is OFF (not in TALK mode).

2. Press the INT button, and SELECT PHONE ID is displayed.

3. Press the number button to input the phone ID you

want to intercom with. For example, to intercom with

extension 2, you need to input “0”, “2”.

4. When ﬁnished, press the INT or TALK button to end the

intercom call.

NOTE: To cancel the intercom call, press INTERCOM.

Memory

The cordless handset and base each have their own

separate memory storage areas. The handset can store

forty phonebook records consisting of 21-character names

and 32-digit telephone numbers.

Storing a Name and Number in Memory

1. Press the STORE button on the handset, ENTER NUMBER

is displayed.

2. Use the keypad to enter the phone number (up to 32

digits).

3. Press the SELECT button. The display shows ENTER NAME.

Telephone Operation

17

4. Use the touch-tone pad to enter a name (up to 21

characters). More than one letter is stored in each of

the number keys. For example, to enter Bill Smith, press

the 2 key twice for the letter B. Press the 4 key 3 times

for the letter I. Press the 5 key 3 times for the letter L.

Press the 5 key 3 times for the second letter L, and press

the 1 key to insert a space between the ﬁrst and last

name. Press the 7 key 4 times for the letter S; press the

6 key once for the letter M; press the 4 key 3 times for

the letter I; press the 8 key for the letter T; press the 4

key twice for the letter H.

5. Press the STORE button again to save your selection.

ENTER LOCATION is displayed.

6. Enter two digits to enter the location, ranging from 01

to 40. For example, to store the record in location #5,

press “0”, “5”. After entering a valid location number,

the record will be saved. If the memory location you

selected is not empty, OVERWRITE? will show in the

display. Press the STORE button again to conﬁrm the

current record and overwrite the old one or press the

EXIT button to select another location.

7. To enter another name and number in a different

memory location, return to step 1 and repeat the process.

Storing a Redial Number

1. Make sure the phone is OFF (not in TALK mode).

2. Press the REDIAL button on the handset to review the

redial number.

3. Press SELECT and ENTER NUMBER is displayed.

4. Then press SELECT again and ENTER NAME is displayed.

5. Use the keypad to enter the names.

6. Press STORE button and ENTER LOCATION is displayed.

7. Enter two digits to enter the location, ranging from 01

to 40. For example, to store the record in location #5,

press “0”, “5”. After entering a valid location number,

the record will be saved.

Inserting a Pause in the Dialing Sequence

Press the #PAUSE button on the touch-tone pad twice

to insert a delay in the dialing sequence of a stored

telephone number when a pause is needed to wait for a

dial tone (for example, after you dial 9 for an outside line,

or wait for a computer access tone.) Each pause counts

as 1 digit in the dialing sequence. The letter “P” in the

displayed number indicates a pause.

Telephone Operation

18

Reviewing, Changing or Deleting Stored

Names/Numbers

To Review: Press DIR/3on the handset, then press the

3or4 button to scroll through the stored numbers. Or

press the memory location number.

To Change: While viewing the record, press the SELECT/

SAVE button. Follow the steps under Storing a Name and

Number in Memory.

To Delete: Press DIR/3on the handset, then press the

3or4 button to scroll to a desired memory.

1. Press the DELETE button. DELETE? is displayed.

2. Press DELETE again to conﬁrm.

Dialing a Stored Number

Make sure the phone is ON (in TALK mode).

1. Press the DIR/3button.

2. Press the desired memory location button (01-40) or

use the 3or4button to scroll to the desired telephone

number.

3. Press SELECT/SAVE to dial the displayed number.

-Or-

1. Make sure the phone is OFF (not in TALK mode).

2. Press the DIR/3 button.

3. Press the desired memory location button (01-40), or

use the 3or4button to scroll to the desired telephone

number.

4. Press the TALK button. The telephone number dials

automatically.

Chain Dialing from Memory

Use this feature to make calls that require a sequence of

numbers, such as a frequently used long distance card

number. The following example shows how you can store

each part of the long dialing sequence and use chain

dialing to make a call through a long distance service

provider:

The Number For Memory Location

Long Distance Access Number 7

Authorization Code 8

Frequently called long distance number 9

Make sure the phone is ON.

1. Press DIR/3 button and then press 0 followed by 7.

Telephone Operation

19

dateCID sequence number line number time

CID phone

number

CID name

2. Press SELECT/SAVE to dial the displayed number.

3. When you hear the access tone, press DIR button and

then press 0 followed by 8.

4. Press SELECT/SAVE to dial the number stored in memory

location 8.

5. At the next access tone, press DIR, 0, 9, then SELECT/

SAVE buttons in sequence.

Caller ID (CID)

NOTE: This feature does not function when using the

handset with base model 25413, as it does not support

Caller ID.

Caller ID (CID) is a service available from your local

telephone company. For Caller ID to work on this system,

you must subscribe to Caller ID service. To receive Caller

ID information for a Call Waiting call, you must subscribe

to the combined Call Waiting Caller ID service.

This telephone system receives and displays CID

information transmitted by your local telephone company.

This information can include the phone number, date and

time; or the name, phone number, and date and time.

Telephone Operation

Receiving and Storing CID Records

When you receive a call, Caller ID information is

transmitted by the phone company to your telephone

between the ﬁrst and second ring. The Caller ID

information appears on your phone’s display while

the phone rings, giving you a chance to monitor the

information and decide whether or not to answer.

If you are not at home or cannot answer, the telephone

stores the information so that you can see who

called while you were unavailable. Caller ID memory

automatically stores the call number, date, time, phone

number and name for the last 40 calls. If Caller ID

memory is full, a new call record automatically replaces

the oldest call record in memory.

20

At any time, you can review the stored information for

the last 40 calls. Any calls received since your last review

are marked as NEW in the display, to remind you to

review them.

Reviewing Call Records

As calls are received and stored, the display is updated to

let you know how many calls have been received.

1. Press the CID/4button ﬁrst. The newest call record will

be shown.

2. Press 3 button to scroll to older call records. When you

reach the oldest call, START/END is displayed.

3. Press 4 button to scroll from the old records to recent

ones.

As you review call records, the display shows you the

following information for each call:

• The telephone number of the caller.

• The numeric order of the call.

• The name of the caller, if available in your service area.

NOTE: If a name is received which exceeds 15 characters,

the extra characters will scroll on the display.

• Time and date the call was received.

• NEW appears for all calls that have not been reviewed.

NOTE: Check with your local phone company regarding

name service availability.

Transferring CID Records to Memory

You may transfer a Caller ID record to your phone’s

memory.

NOTE: It is important that you format CID records

correctly before storing in memory. It is not possible to

reformat CID records stored in memory.

1. Use the CID/4button to scroll to the desired record.

2. Press the STORE button.

3. Press the desired memory location. Example, press the

number 01 key to store the record in memory location

1. You will hear a conﬁrmation tone.

NOTE: If the memory location you selected currently has a

record stored, the prompt message “OVERWRITE ?” will be

shown. Press STORE button again to conﬁrm overwrite, or

press EXIT button to select another location.

Telephone Operation

Page is loading ...

RCA Cordless Telephone 25413 User manual

This manual is also suitable for

RCA Cordless Telephone 25413 User manual

in other languages

Related papers

Other documents