Ferm PDM1001 Owner's manual

Brand: Ferm

Model: PDM1001

Category: Rotary hammers

Type: Owner's manual

This manual is also suitable for

Page is loading ...

2 Ferm

Product: Ferm Percussion drill.

Type FPD-13/650, Art.nr. 319306

Ferm, Genemuiden, The Netherlands.

Sound pressure level (L

) 92,9 dB(A)

Sound power level (L

) 105,9 dB(A)

Vibration (

) 7,3 m/s

SERIAL NUMBER

The serial number on the machine consists of the fol-

lowing elements.

Serial nr.

CAREFULLY READ THE INSTRUCTIONS BE-

FORE YOU USE THE PERCUSSION DRILL!

1. SPECIAL SAFETY RULES

BEFORE OPERATING THE MACHINE:

1. Check the following:

- do the voltage of the machine correspond with the

mains voltage

- are the mains lead and the mains plug in a good con-

dition.

2. Do not use extension cables which are too

long. Use extension cables with a core diameter of

1,75 mm

minimal and only when the cable is rolled

out completely.

In case of a blockage, switch of the machine immediately.

Always compare the maximum rotation speed of accesoi-

res with the maximum speed of the percussion drill.

5. Never attach de chuck key with a rope to the percus-

sion drill.

6. Pull the mainsplug from the socket before you change

a drill or accessory.

WHEN OPERATING THE MACHINE:

1. Check if the switch is placed in the ‘OFF’-position be-

fore you connect the machine to mains.

2. Keep the mains cable away from moving parts of the

machine.

3. First switch off the machine before you move the ma-

chine downwards along your body.

4. Never cover the ventilationslots.

IMMEDIATELY SWITCH OFF THE MACHINE

IN CASE OF:

1. Excessive sparking of the brushes and verticiliosis in

the collector.

2. Malfunction of the mainsplug, -socket or damaged ca-

bles.

3. Broken switch.

4. Smoke or smell caused by scorched insulation.

2. BEFORE OPERATING

THE MACHINE

1. Use only sharp drills of the following types:

Concrete/masonry

Hard metal

Metal HSS

Wood HSS

MOUNTING ACCESSORIES

Prior to mounting an accessory always unplug the tool.

Placing and removing bits

In addition to bits the machine can also hold screw bits

with a hexagonal shaft.

• On the collarscrew the drill chuck open.

• Place the shaft of the bit in the opening of the drill

chuck.

• Tighten the drill chuck until the click point has been

reached. The bit is now in fixed in the drill chuck.

• To change a bit, unscrew the drill chuck open again.

• Slide the sidegrip over the drillhead.

• Slide the measuring rod in the sidegrip and tighten the

ORDER NUMBER/YEAR OF CONSTRUCTION

Ferm 27

AVAILABLE SPARE PARTS FOR FPD-13/650

REF.NR. DESCRIPTION FERM.NR.

1 LEFT HAND SCREW (FOR DRILL CHUCK) 406387

2 DRILL CHUCK 956000

8 GEAR 407382

15 ARMATURE 407383

17 FIELD COIL 407385

20 CARBON BRUSH (SET) 407386

22 CARBON BRUSH HOLDER 407389

25 SWITCH 407384

- SIDE HANDLE 407388

EXPLODED VIEW

V~/Hz W /min mm /min mm mm mm

230/50 650

0 -2500

13 0-40000

25 13

26 Ferm

Ferm 3

grip.

•

Tighten the workpiece to a workbench by using a clamp.

• When all preparations are done the machine can be

connected to mains. First check if the switch is in the

‘OFF’-position and if the rotationswitch is in the

RIGHT-position.

3. OPERATION

1. THE ON/OFF SWITCH

Switch the machine on by pressing the triggerswitch (A).

When you release the triggerswitch (A) the machine will

turn off.

2. SWITCH-LOCK

You can lock the On/Off switch by pressing the triggers-

witch (A) and then pressing knob (B). Release the switch-

lock by pressing the triggerswitch (A) shortly.

3. SPEED-CONTROL

The rotation-speed can be

continuously adjusted be-

tween 0 and 2500 rota-

tions per minute, by pres-

sing the switch (A) deeper

or less deep.

4. ADJUSTING OF THE MAXIMUM ROTA-

TIONSPEED

Switch the machine on by pressing triggerswitch (A);

- Lock the triggerswitch (A) by pressing knob (B);

- Adjust the speed by turning the small wheel (C) to the

desired maximum rotation speed.

5. SWITCHING THE DIRECTION OF ROTA-

TION

- Direction of rotation counter-clockwise: shift switch

(D) to “L”;

- Direction of rotation clockwise: shift switch (D) to

“R”.

6. SWITCH FOR PERCUSSION DRILLING

With the switch on top

of the machine you can

select normal or percus-

sion drilling.

-Slide the switch to

the “Drill” symbol

for normal drilling;

-Slide the switch to the “Hammer” symbol for per-

cussion drilling.

4. MAINTENANCE

While maintaining and cleaning the machine

pull the plug from the mainssocket. Never use

water or other agressive liquids while cleaning

electrical parts of the lamp.

- Keep the mains cord of the machine clean, some fluids

contain solvents can dissolve plastic parts of the ma-

chine.

- Keep the ventilation slots of the machine clean to pre-

vent overheating of the motor.

5. MALFUNCTION

Below we have listed a number of possible causes and

corresponding solutions in case the machine does not

function as it should:

1. Excessive sparkling.

This usely indicates dirt in the motor or worndown

carbon brushes.

- Bring your percussion drill to your Ferm-dealer.

2. The percussion drill is overheating.

The ventilationslots are covered with dirt.

- Clean them with a dry cloth.

The percussion drill is overloaded.

- Use the machine for work for which it is ment to be.

- Replace the drill for a sharp one or sharpen the drill by

using a benchgrinder and a Twist drill grinding attach-

ment.

The motor is defect.

- Bring your percussion drill to your Ferm-dealer for re-

pairance.

ClEl

■

DECLARATION OF CONFORMITY

(

)

We declare under our sole responsability that this

product is in conformity with the following

standards or standardized documents

EN50144-2-1, EN50144-1

EN55014-1, EN61000-3-2, EN61000-3-3, EN55014-2

in accordance with the regulations:

98/37/EEC

73/23EEC

89/336/EEC

from 01-06-2000

GENEMUIDEN NL

G.M. Ensing

Quality department

Page is loading ...

Ferm PDM1001 Owner's manual

Brand: Ferm

Model: PDM1001

Category: Rotary hammers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: Ferm PDM1001 Le manuel du propriétaire
español: Ferm PDM1001 El manual del propietario
Deutsch: Ferm PDM1001 Bedienungsanleitung
Nederlands: Ferm PDM1001 de handleiding
dansk: Ferm PDM1001 Brugervejledning
svenska: Ferm PDM1001 Bruksanvisning
suomi: Ferm PDM1001 Omistajan opas

Ferm PDM1001 Owner's manual

This manual is also suitable for

Ferm PDM1001 Owner's manual

in other languages

Related papers

Other documents