Metabo W 11-125 Quick Operating instructions
- Category
- Power tools
- Type
- Operating instructions
www.metabo.com Made in Germany
en Operating Instructions 5
fr Mode d'emploi 12
es Instrucciones de manejo 20
W 8-115
W 8-115 Quick
W 8-125
W 8-125 Quick
WE 9-125 Quick
W 11-125 Quick
W 11-150 Quick
WE 14-125 Inox Plus
WE 14-125 Plus
WE 14-125 Quick
WE 14-125 VS
WE 14-150 Plus
WE 14-150 Quick
WE Partner Edition
WP 8-115 QuickProtect
WP 8-125 QuickProtect
WP 11-125 QuickProtect
WP 11-150 QuickProtect
WEP 14-150 QuickProtect
WEP 14-150 QuickProtect HT
Page is loading ...
3
Metabowerke GmbH, Postfach 1229, Metabo-Allee 1, D-72622 Nuertingen, Germany
W 8-115
W 8-115 Quick
WP 8-115 QuickProtect
W 8-125
W 8-125 Quick
WP 8-125 QuickProtect
W 11-125 Quick
WP 11-125 QuickProtect
W 11-150 Quick
WP 11-150 QuickProtect
WE 9-125 Quick
WE 14-125 Inox Plus
WE 14-125 Plus
WE Partner Edition
WE 14-125 VS
WE 14-150 Plus
WE 14-150 Quick
WEP 14-150 QuickProtect
WEP 14-150 QuickProtect HT
Quick
- Q - QQQQQQ - QQQ
Electronic
------VCVTCVTCVTCVTCTCTC
D
max
mm (in)
115 (4
1
/
2
) 125 (5) 150 (6) 125 (5) 125 (5) 150 (6) 150 (6) 150 (6)
t
max1
; t
max2
; t
max3
mm (in)
10; 8; 6,8
(
3
/
8
;
5
/
16
;
1
/
4
)
10; 8; 6
(
3
/
8
;
5
/
16
;
1
/
4
)
M / l - / mm (in)
5/8“-11 UNC / 22 (
7
/
8
)
n min
-1
(rpm)
10000 10000 10000 10000 10000 9000
3000-
10000
2000-
7000
7000-
10500
2800-
10500
6000-
9000
8000 8000
P
1
W
800 800 800 800 1100 1100 950 1400 1400 1400 1400 1400 1400
P
2
W
490 490 490 490 670 670 540 800 800 760 800 800 800
I
120 V
A
8 8 8 8 9,6 9,6 8,5 12,2 12,2 12,2 12,2 12,2 12,2
m kg (lbs)
1,8 (4.0) 1,9 (4.2)
13.
Page is loading ...
ENGLISH en
5
Operating Instructions
The angle grinders, when fitted with original Metabo
accessories, are suitable for grinding, sanding,
separating and wire brushing metal, concrete,
stone and similar materials without the use of water.
WE 14-125 VS is also suitable for polishing.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
WARNING – Reading the operating
instructions will reduce the risk of injury.
For your own protection and for the
protection of your power tool pay
attention to all parts of the text that are
marked with this symbol!
General Power Tool Safety Warnings
WARNING Read all safety warnings and
all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury. Save all warnings and
instructions for future reference! The term
"power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated
(cordless) power tool.
2.1 Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2.2 Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
2.3 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
2.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
1. Specified Use
2. General Safety Instructions
ENGLISHen
6
preventive safety mea ures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
3.1 Safety Warnings Common for Grinding,
Sanding, Wire Brushing or Abrasive
Cutting-Off Operations:
a) This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power
tool. Failure to follow all the instructions may result
in electric shock, fire and/or serious injury.
WE 14-125 VS may also be used as a polisher.
b) Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury. (This does not apply to WE 14-125 VS.)
c) Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f) The arbour size of wheels, flanges, backing
pads or any other accessory must properly fit
the spindle of the power tool. Accessories with
arbour holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and a workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure
to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of
operation.
j) Hold power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and shock the
operator.
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled into
the spinning accessory.
I) Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grap the surface and pull
the power tool out of your control.
m) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
o) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
3. Special Safety Instructions
ENGLISH en
7
3.2 Kickback and Related Warnings:
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or any
other accessory. Pinching or snagging causes rapid
stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of
the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades create
frequent kickback and loss of control.
3.3 Safety Warnings Specific for Grinding
and Abrasive Cutting-Off Operations:
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed
towards the operator. The guard helps to protect
the operator from broken fragments, accidental
contact with the wheel and sparks which could
ignite clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
d) Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
e) Do not use worn down wheels from larger
power tools.
Wheels intended for larger power
tools are not suitable for the higher speed of a
smaller tool and may burst.
3.4 Additional Safety Warnings Specific for
Abrasive Cutting-Off Operations:
a) Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
of kickback or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel. When the wheel, at the
point of operation, is moving away from your body,
the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting
a cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted in
the workpiece.
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
f) Use extra caution when making a "pocket
cut" into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
3.5 Safety Warnings Specific for Sanding
Operations:
a) Do not use excessively oversized sanding
disc paper. Follow manufacturers
recommendations when selecting sanding
paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc or kickback.
3.6 Only for WE 14-125 VS: Special safety
instructions for polishing:
Loose parts on the polishing guard, especially
the fastening cords, are not permitted. Tuck
away or shorten the fastening cords. Loose,
spinning fastening cords may make contact with
your fingers or become caught in the workpiece.
ENGLISHen
8
3.7 Safety Warnings Specific for Wire
Brushing Operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load
and centrifugal forces.
3.8 Additional Safety Instructions
WARNING – Always wear protective
goggles.
For safety reasons the guard
must protrude at least 9/64"
(3.4 mm) beyond the wheel.
Double check especially
wheels with an included hub.
Use elastic cushioning layers if they have been
supplied with the abrasive and if required.
Observe the specifications of the tool or accessory
manufacturer! Protect the discs from grease or
impacts!
Grinding wheels must be stored and handled with
care in accordance with the manufacturer's
instructions.
Never use parting grinder discs for roughing work!
Do not apply pressure to the side of parting grinder
discs.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
If accessories with threaded inserts are used, the
end of the spindle may not touch the base of the
hole on the grinding tool. Make sure that the thread
in the accessory is long enough to accommodate
the full length of the spindle. The thread in the
accessory must match the thread on the spindle.
See page 2 and chapter 13. Technical
Specifications for more information on the spindle
length and thread.
During machining, of metals in
particular, conductive dust can form
deposits inside the machine. This can lead to the
transfer of electrical energy onto the machine
housing. This can mean a temporary danger of
electric shocks. This is why it is necessary when the
machine is running to blow compressed air through
the rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
We recommend using a stationary extractor system
and connecting a residual current circuit-breaker
(FI) upstream. When the angle grinder is shut down
via the FI circuit-breaker, it must be checked and
cleaned. See chapter 8. Cleaning for more
information on cleaning the motor.
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in
conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing
asbestos must only be treated by specialists.
- Where the use of a dust extraction device is
possible it shall be used.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
Materials that generate dusts or vapours that may
be harmful to health (e.g. asbestos) must not be
processed.
When working in dusty conditions, ensure that
ventilation openings are not blocked. If it becomes
necessary to remove dust, first disconnect the
power tool from the mains supply (use non-metallic
objects) and avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and loadbearing walls (static).
Connect a FI circuit-breaker with max. release
current (30 mA) upstream when using the machine
outdoors!
Pull the plug out of the socket before any making
adjustments, converting or servicing the machine.
Metabo S-automatic safety clutch. When the safety
clutch responds, switch off the machine
immediately!
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
This power tool is not designed for polishing
(does not apply for WE 14-125 VS.). Improper use
of the machine will void the warranty! The motor
may overheat and damage the electric power tool.
We recommend using our angle polisher for
polishing work.
Symbols on the tool:
..........Class II Construction
V..............volts
A..............amperes
Hz............hertz
.../min ......revolutions per minute
~..............alternating current
.............alternating current /direct current
n ..............rated speed
The "C" and "US" indicators adjacent to the
CSA Mark signify that the product has been
evaluated to the applicable CSA and ANSI/
UL Standards, for use in Canada and the U.S.,
respectively.
ENGLISH en
9
See page 2.
1 "Quick" clamping nut *
2 Support flange
3Spindle
4 Spindle locking button
5 Sliding
on/off switch *
6 Electronic signal indicator *
7 Speed adjustment wheel *
8Switch-on lock *
9 Trigger *
10 Additional handle / Additional handle with vibration
damping *
11 Safety cover
12 Clamping nut *
13 2-hole spanner *
14 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
5.1 Attaching the additional handle
Always work with the additional handle
attached (10)! Attach the additional handle
on the left or right of the machine and secure.
5.2 Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 10.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See page 2, illustration G.
- Push and hold the lever (14). Place the safety
guard (11) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work
(see chapter 10. Accessories).
6.1 Locking the spindle
- Press in the spindle locking button (4) and turn the
spindle (3) by hand until the spindle locking button
engages.
6.2 Placing the grinding wheel in position
See illustration A on page 2.
- Place the supporting flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Place the grinding wheel on the support flange (2).
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
6.3 Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the "Quick" clamping nut (1):
Do not use the
"Quick" clamping nut if the
accessory has a clamping shank thicker than
8mm
(5/16“)! In this case, use the
clamping nut (12)
with 2-hole spanner (13).
- Lock the spindle (see chapter 6.1).
- Position the "Quick" clamping nut (1) on the
spindle (3) so that the 2 lugs engage in the
2 grooves on the spindle. See illustration
on page 3.
- Tighten the "Quick" clamping nut by turning
clockwise by hand.
- Turn the grinding wheel firmly clockwise to tighten
the "Quick" clamping nut.
Releasing the "Quick" clamping nut (1)
:
The "Quick" clamping nut (1) must be attached
before the spindle locking button (4) can hold
the spindle!
- The machine continues to run after switching off.
- Press in the spindle locking button (4) just before
the grinding wheel stops. The "Quick" clamping
nut (1) is released.
6.4 Securing/Releasing the clamping nut
(depending on features)
Securing the clamping nut (12):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See illustration B on page 2.
- X) For thin grinding wheels:
The edge of the clamping nut (12) faces upwards
so that the thin grinding wheel can be attached
securely.
Y) For thick grinding wheels:
The edge of the clamping nut (12) faces
downwards so that the clamping nut can be
attached securely to the spindle.
4. Overview
5. Commissioning
6. Attaching the grinding wheel
ENGLISHen
10
- Lock the spindle. Turn the clamping nut (12)
clockwise using the 2-hole spanner (13) to secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 6.1). Turn the
clamping nut (12) anticlockwise using the 2-hole
spanner (13) to unscrew.
7.1 Adjusting the speed
(depending on features)
Set the recommended speed at the setting
wheel (7).
Parting grinder and roughing discs, cup wheel,
diamond parting wheel: high speed
Brush: medium speed
Grinding wheel: low to medium speed
Note:
We recommend using our angle polisher for
polishing work.
7.2 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
Machines with slide switch:
Switching on: Push the slide switch (5) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the slide
switch (5) and release.
Machines with "Ergo Paddle Switch" (with
dead man function):
(machines with the designation WP..., WEP...)
Switching on: Slide the switch-on lock (8) in
the direction of the arrow and press
the trigger (9).
Switching off: Release the trigger (9).
7.3 Working instructions
Grinding and sanding operations:
Press down the machine evenly on the surface
and move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of 30° -
40° for the best working results.
Separating:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Machines with VTC and TC electronics:
The electronic signal display (6) lights up and
the load speed decreases.
The coil temperature is
too high! Run the machine in idling until the
electronics signal indicator switches off.
Machines with VTC, TC and VC electronics:
The electronic signal display (6) flashes
and the machine does not start. The restart
protection is active. If the mains plug is
inserted with the machine switched on, or if the
current supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
Use only genuine Metabo accessories. See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Safety guard for cut-off grinding
Designed for work with cut-off wheels, diamond
cut-off wheels.
Install as described under "Safety guard for
grinding" (chapter 5.2).
B Cut-off grinding safety guard with guide
carriage
Designed for cutting through stone slabs with
diamond cut-off wheels.
7. Use
0
I
5
0
I
8 989
8. Cleaning
9. Troubleshooting
10. Accessories
ENGLISH en
11
Mount on machine and secure with screw. With
nozzle for extracting stone dust using a suitable
extractor.
C Hand guard for sanding and wire brushing
operations
Designed for work with support plates, sanding
pads, wire brushes.
Install hand guard under the additional side-
mounted handle.
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Explanation of details on page 2 . Subject to
changes serving technical progress.
D
max
=max. diameter of accessory
t
max,1
=max. permitted thickness of clamping
shank on accessory when using clamping
nut (12)
t
max,2
=max. permitted thickness of clamping
shank on accessory when using "Quick"
clamping nut (1)
t
max,3
=Roughing disc/Parting disc:
max. permitted thickness of
accessory
M=Spindle thread
l =Length of the grinding spindle
n* =Rated speed (maximum speed)
P
1
=Nominal power input
P
2
=Power output
I
120 V
=Current at 120 V
m =Weight without mains cable
Wear ear protectors!
* Machines with the designation WE...:
Energy-rich, high-frequency interference can cause
fluctuations in speed. The fluctuations disappear,
however, as soon as the interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
11. Repairs
12. Environmental Protection
13. Technical Specifications
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
170 26 9910 - 1014
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Metabo W 11-125 Quick Operating instructions
- Category
- Power tools
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Metabo WE 14-150 Plus User manual
-
-
Metabo WP 1100-125 Operating instructions
-
Metabo W 750-115 Operating instructions
-
-
-
Metabo W 780 Operating Instructions Manual
-
-
Metabo W 820-125 Operating instructions
-