Lithonia Lighting COMPANL2X24KMVOLTDIM Installation guide

Lithonia Lighting
Brand
Lithonia Lighting
Model
COMPANL2X24KMVOLTDIM
Category
Decorative lighting
Type
Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS / DIRECTIVES D’INSTALLATION / INSTRUCCIONES
CPANL LED Flat Panel Light Fixture
Panneau à Plat / Luminaria - Panel de Luz Plano
TOOLS REQUIRED
FOR INSTALLATION
• Safety glasses
• Drill with 1/8” drill bit
• Phillips screwdriver
• Pencil
• Hammer
• Pliers
• Ruler
• Wire Strippers
• Flat blade screwdriver
OUTILS REQUIS POUR L’INSTALLATION
• Lunettes de sécurité
• Perceuse, avec un foret de 1/16 po
• Tournevis à tête Phillips
• Crayon
• Marteau
• Pinces
• Régle
• Outil à dénuder
• Tournevis à lame plate
Rev A 5/18
Protect yourself. Before installing,
read these instructions carefully and
save them for future reference.
Date Installed:________________
Pour votre propre protection. Avant de procéder à
l’installation, veuillez lire attentivement ces directives
et les conserver pour référence ultérieure.
Date de l’installation : ________________
Protéjase. Antes de instalar, lea estas
instrucciones cuidadosamente
y guárdelas para futura referencia.
Fecha Instalada:________________
*Model Number / Numéro des modèle / Número de Modelo
noted on product or carton label
MODELS:
CPANL 2X2 24/33/44LM __K
CPANL 2X4 40/50/60LM __K
CPANL 1X4 24/33/44LM __K
CPANL 2X2 3400LM __K
CPANL 2X4 4000LM __K
CPANL 1X4 4000LM __K
222826
C US
HERRAMIENTAS NECESSARIAS PARA
LA INSTALACIÓN
• Lentes de seguridad
• Taladro con broca de 1/16”
• Destornillador de Phillips
• Làpiz
• Martillo
• Pinzas
• Regla
• Pelacables
• Destorniallador plano
Page 2
LED IMPORTANT SAFETY INSTRUCTIONS
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and
other hazards please read all warnings and instrucons included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing roune maintenance upon this equipment, follow these general precauons.
• Installaon and service of luminaires should be performed by a qualified licensed electrician.
•
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construcon and operaon
and any hazards involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient
dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a soluon of warm
water and any mild, non-ab
rasive household detergent, rinsed with clean water and wiped dry. Should opcal assembly
become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been
damaged during transit. Inspect to confirm. Any part damaged or broken during or aer assembly should be replaced.
• Recycle: For in
formaon on how to recycle LED electronic products, please visit www.epa.gov.
• These instrucons do not purport to cover all details or variaons in equipment nor to provide every possible conngency
to meet in connecon with installaon, operaon, or maintenance. Should further informaon be desired or should
parcular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this maer should be
referred to Acuity Brands Lighng, Inc.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
Disconnect or turn off power before
installaon or servicing.
Verify that supply voltage is correct by
comparing it with the luminaire label
informaon.
Make all electrical and grounded
connecons in accordance with the Naonal
Electrical Code (NEC) and any applicable
local code requirements.
All wiring connecons should be capped
with UL approved recognized wire
connectors.
WARNING
RISK OF ELECTRIC SHOCK
Allow lamp/fixture to cool before handling.
Do not touch enclosure or light source.
Do not exceed maximum waage marked on
luminaire label.
Follow all manufacturer’s warnings,
recommendaons and restricons for: driver
type, burning posion, mounng
locaons/methods, replacement and
recycling.
WARNING
RISK OF BURN
Wear gloves and safety glasses at all mes
when removing luminaire from carton,
installing, servicing or performing
maintenance.
Avoid direct eye exposure to the light source
while it is on.
CAUTION
RISK OF INJURY
Keep combustible and other materials that
can burn, away from lamp/lens.
Do not operate in close proximity to persons,
combusble materials or substances
affected by heat or drying.
CAUTION
RISK OF FIRE
Page 3
LED IMPORTANT SAFETY INSTRUCTIONS
Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory
statements.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and
Conditions, please visit www.acuitybrands.com.
Acuity Brands Lighng, Inc. assumes no responsibility for claims arising out of improper or careless installaon or handling of its products.
ABL LED General Warnings, Form No. 503.203
© 2016 Acuity Brands Lighng, Inc. All rights reserved. 04/01/16
Never connect components under load.
Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire
insulaon.
Unless individual product specificaons deem otherwise: Never connect an LED product directly to a
dimmer packs, occupancy sensors, ming devices, or other related control devices. LED fixtures must be
powered directly off a switched circuit.
Unless individual product specificaons deem otherw
ise: Do not restrict fixture venlaon. Allow for
some volume of airspace around fixture. Avoid covering LED fixtures with insulaon, foam, or other
material that will prevent convecon or conducon cooling.
Unless individual product specificaons deem otherwise: Do not exceed fixtures maximum ambient
temperature.
Only use fixture in its intended locaon.
LED products are Polarity Sensive. Ensure proper Polarity before insta
llaon.
Electrostac Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be
worn during all installaon or servicing of the unit.
Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter
performance.
Some components inside the fixture may not be serviceable. In the unlikely event your unit may require
service, stop using the unit immediately and contact an ABL represen
tave for assistance.
Always read the fixtures complete installaon instrucons prior to installaon for any addional fixture
specific warnings.
CAUTION: RISK OF PRODUCT DAMAGE
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page 10
CPANL - INSTALLATION INSTRUCTIONS
CPANL - INSTRUCTIONS D'INSTALLATION
CPANL - INSTRUCCIONES DE INSTALACIÓN
EN: ENGLISH, FR: FRANÇAIS, ES: ESPAÑOL
*SAVE THESE INSTRUCTIONS
*CONSERVEZ CES INSTRUCTIONS
*GUARDA ESTAS INSTRUCCIONES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Lithonia Lighting COMPANL2X24KMVOLTDIM Installation guide

Lithonia Lighting
Brand
Lithonia Lighting
Model
COMPANL2X24KMVOLTDIM
Category
Decorative lighting
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents