Duerkopp Adler 550-867 User manual

Brand: Duerkopp Adler

Model: 550-867

Category: Car kits

Type: User manual

Duerkopp Adler 550-867: This advanced sewing machine sensor upgrade kit enhances thread tension control and seam quality. The BTSR sensor detects thread breaks and automatically stops the machine, preventing costly material waste and skipped stitches. Easy to install, it seamlessly integrates with your existing Duerkopp Adler machine. Upgrade now for improved efficiency and peace of mind.

550-867

Additional Instructions

BTSR sensor

Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of these contents, in-

cluding extracts, is prohibited without the prior written approval of Dürkopp Adler GmbH.

Table of Contents

Additional Instructions 550-867 - 02.0 - 01/2021

1 Kit components .......................................................................... 3

2 Work preparation........................................................................ 4

3 Replacing the thread tension PCB............................................ 6

4 Dismantling the old parts........................................................... 9

4.1 Dismantling the thread lever protection and thread clamp ........... 9

4.2 Dismantling the BTSR sensor and thread guide......................... 10

5 Fitting the new parts ................................................................ 12

5.1 Fitting the thread guide............................................................... 12

5.2 Installing the BTSR sensor ......................................................... 13

5.3 Fitting the thread clamp .............................................................. 14

5.4 Installing thread lever protection................................................. 15

5.5 Machine following upgrade......................................................... 16

Table of Contents

Additional Instructions 550-867 - 02.0 - 01/2021

Kit components

Additional Instructions 550-867 - 02.0 - 01/2021

1 Kit components

Check whether the scope of delivery for parts set 0867 590094 is correct

prior to upgrade.

Abb. 1: Comparison of replacement parts

Material number Quantity Description

0867 100540 1 Thread lever protection

0867 110183 1 Thread guide

0867 110431 1 Threading procedure sticker

9835 901006 1 Antistatic armband

0791 550662 DE 1 BTSR sensor upgrade manual

0791 550662 EN 1 BTSR sensor upgrade manual

Old

New

PCB

Thread lever protection

Thread guide

Work preparation

Additional Instructions 550-867 - 02.0 - 01/2021

2 Work preparation

Before performing the upgrade, the power needs to be switched off:

1. Turn the power switch (1) to the O position.

Abb. 2: Turning off the main switch

 The lamp (2) on the UPS power unit (4) lights up.

Abb. 3: Switching off the power

DANGER

Risk of injury from electric shock.

Switch off the machine and disconnect the power

plug before you upgrade the sensor.

Make sure the power plug cannot be accidentally

plugged back in.

①

(1) - Main switch

②

③

(2) - Lamp

(3) - Off button

(4) - UPS power unit

④

Work preparation

Additional Instructions 550-867 - 02.0 - 01/2021

2. Press and hold down the off button (3) for 3 seconds.

 The lamp (2) goes out, the machine is powered down.

Abb. 4: Machine powered down

②

(2) - Lamp

Replacing the thread tension PCB

Additional Instructions 550-867 - 02.0 - 01/2021

3 Replacing the thread tension PCB

Checking the power

1. Open the control cabinet, the key for which is included with the machine.

2. Check whether LED (1) is lit up.

 If LED (1) is NOT lit up, there is no power.

3. If LED (1) is still lit up, turn off the power,  2 Work preparation, p. 4.

Abb. 5: Checking the power

WARNING

Risk of injury from electricity

Double-check that the power is turned off.

Disconnect the machine from the power supply.

ATTENTION

Electrostatic charging may cause damage to equipment!

Work on the machine is ONLY permitted while wearing the antistatic

armband.

Handle the PCB only by its edges.

Do not push the PCB over a surface.

(1) - LED

①

Replacing the thread tension PCB

Additional Instructions 550-867 - 02.0 - 01/2021

Putting on the antistatic armband

1. Fasten the antistatic armband (2) to the mechanic's arm.

2. Fasten the clamp (3) of the antistatic armband (2) to equipotential

bonding (4) on the control cabinet.

Abb. 6: Antistatic armband

Removing the PCB

1. Loosen all four screws (7) and remove the PCB (5).

2. Release the screws (6) on the plugs.

3. Pull off the plug (6).

Abb. 7: Removing the PCB

(2) - Antistatic armband

(3) - Clamp

(4) - Equipotential bonding

②

③

④

②

④

(5) - PCB

(6) - Plug

(7) - Screws

⑤

⑥

⑦

⑥

Replacing the thread tension PCB

Additional Instructions 550-867 - 02.0 - 01/2021

Abb. 8: Pulling off the plug

Inserting the PCB

1. Remove the new PCB from its antistatic bag.

2. Connect the plug (6) to the PCB.

3. Tighten the screws (6) on the plugs.

4. Screw the PCB (5) onto the stud bolts.

5. Tighten the PCB (5) to the stud bolts using the 4 screws (7).

Abb. 9: PCB packed in antistatic bag

(6) - Plug

⑥

Dismantling the old parts

Additional Instructions 550-867 - 02.0 - 01/2021

4 Dismantling the old parts

4.1 Dismantling the thread lever protection and thread clamp

Abb. 10: Dismantling thread lever protection

1. Loosen the screws (4) on the thread lever protection (5).

2. Remove the thread lever protection (5).

3. Loosen screw (1) on the head cover (2) and remove it.

4. Loosen screw (3) on the head cover (2).

5. Turn the head cover (2) back slightly.

6. Refit the screw (3) in order to keep the head cover (2) in its position.

④

②

⑤

③

①

(1) - Screw

(2) - Head cover

(3) - Screw

(4) - Screws (concealed)

(5) - Thread lever protection

Dismantling the old parts

Additional Instructions 550-867 - 02.0 - 01/2021

Abb. 11: Dismantling the thread clamp

7. Release screw (6) on the thread clamp (7).

8. Remove the thread clamp (7).

4.2 Dismantling the BTSR sensor and thread guide

Abb. 12: Dismantling the BTSR sensor

1. Loosen the nut (1) with a 7 mm wrench.

2. Remove the nut (1), washer and screw of the BTSR sensor.

⑥

⑦

(6) - Screw (7) - Thread clamp

①

(1) - Nut

Dismantling the old parts

Additional Instructions 550-867 - 02.0 - 01/2021

Abb. 13: Dismantling the thread guide

3. Loosen the screws (2).

4. Remove the thread guide (3).

(2) - Screws (3) - Thread guide

②

③

Fitting the new parts

Additional Instructions 550-867 - 02.0 - 01/2021

5 Fitting the new parts

5.1 Fitting the thread guide

Abb. 14: Installing the thread guide

1. Attach the thread guide (2).

2. Tighten the screws (1).

3. The thread guide (2) must lie flush against the machine - bend the

thread guide (2) by hand if necessary.

Bend if required

Abb. 15: Position of thread guide

1. Check the position of the thread guide on the sewing machine arm.

2. If the position is correct, continue fitting the BTSR sensor.

①

(1) - Screws (2) - Thread guide

②

Position correct, lying

fully flush against the

sewing machine arm

Too far away from the

sewing machine arm

Fitting the new parts

Additional Instructions 550-867 - 02.0 - 01/2021

3. If the position is NOT correct, the thread guide will have to be bent

slightly.

Abb. 16: Bending the thread guide

4. Bend the thread guide using a pair of pliers in the upper left area (3).

5. Bend the thread guide back again afterwards in the right-hand area (4)

if necessary.

5.2 Installing the BTSR sensor

Abb. 17: Installing the BTSR sensor

1. Fit the nut (3), washer and screw of the BTSR sensor.

2. Tighten the nut (3) with a 7 mm wrench.

(3) - Upper left area (4) - Right area

③

④

(3) - Nut

③

Fitting the new parts

Additional Instructions 550-867 - 02.0 - 01/2021

5.3 Fitting the thread clamp

Abb. 18: Fitting the thread clamp

1. Insert the thread clamp (1) ensuring that the edge (4) of the thread

clamp is parallel to the edge (4) of the BTSR sensor.

2. Tighten the screw (2).

Abb. 19: Attaching the sticker

Attaching the threading procedure

1. Remove the white protective film from the sticker (3).

2. Place the sticker (3) into position.

3. Press down on the sticker (3) so it is firm.

4. Carefully remove the transparent mounting film.

(1) - Thread clamp (2) - Screw

①

②

③

(3) - Sticker

(4) - Edges, parallel

④

Fitting the new parts

Additional Instructions 550-867 - 02.0 - 01/2021

5.4 Installing thread lever protection

Abb. 20: Installing thread lever protection

1. Attach the thread lever protection (6) so that it is located as far down

from the sensor and as much to the right as possible from this and

thereby does not collide with the thread lever (4) .

2. Check the thread lever protection (6) does not collide with the thread

lever (4).

3. Tighten the screws (5) on the thread lever protection (6).

4. Loosen the screw (3) on the head cover (2).

5. Position the head cover (2) so it is flush with the machine again.

6. Insert the screw (1) on the head cover.

7. Tighten screws (1) and (3).

Abb. 21: Positioning the thread lever protection

④

②

⑤

③

①

(1) - Screw

(2) - Head cover

(3) - Screw

(4) - Thread lever

(5) - Screws (concealed)

(6) - Thread lever protection

⑥

Fitting the new parts

Additional Instructions 550-867 - 02.0 - 01/2021

5.5 Machine following upgrade

To be able to use the sensor, it is important to pay attention to the following

points:

• the thread guide (1) must lie flush against the sewing machine arm

 5.1 Fitting the thread guide, p. 12.

• the edge (2) of the thread clamp must be parallel to the edge (2) of

the BTSR sensor,  5.3 Fitting the thread clamp, p. 14

Abb. 22: bMachine with mechanical thread tension plate

Abb. 23: Machine with electronic thread tension plate

(1) - Thread guide (2) - Edges, parallel

①

②

(1) - Thread guide (2) - Edges, parallel

①

②

DÜRKOPP ADLER GmbH

Potsdamer Str. 190

33719 Bielefeld

Germany

Phone +49 (0) 521 925 00

E-Mail: [email protected]m

www.duerkopp-adler.com

Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany

Duerkopp Adler 550-867 User manual

Brand: Duerkopp Adler

Model: 550-867

Category: Car kits

Type: User manual

Download PDF

report

Duerkopp Adler 550-867 User manual

Duerkopp Adler 550-867 User manual

Related papers

Other documents