Chief NS1D20P Installation guide
- Category
- Rack accessories
- Type
- Installation guide
Chief NS1D20P is a rack door accessory designed for use with S1 racks. It features a perforated design for ventilation and enhanced airflow, ensuring optimal performance of your rack-mounted equipment. The door is easy to install and remove, providing convenient access to your equipment for maintenance or troubleshooting.
Chief NS1D20P is a rack door accessory designed for use with S1 racks. It features a perforated design for ventilation and enhanced airflow, ensuring optimal performance of your rack-mounted equipment. The door is easy to install and remove, providing convenient access to your equipment for maintenance or troubleshooting.
INSTALLATION INSTRUCTIONS
NS1D12F
NS1D12P
NS1D12S
S1 Racks Doors
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
NS1D12-20-28-36-41
NS1D12-20-28-36-41 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Installation Instructions NS1D12-20-28-36-41
3
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
7/16"
OR
OR
A (1)
[Door]
B (1)
[Door catch]
C (1)
[Top door support]
E (2)
1/4-20 x 5/8"
F (2)
1/4-20
[Perforated] [Solid]
[Plexiglass]
(NS1D12P shown)
(NS1D12F shown)
(NS1D12S shown)
[Lower door support]
D (1)
NS1D12-20-28-36-41 Installation Instructions
4
INSTALLATION
IMPORTANT ! : If installing doors and side panels (not
included) on an S1 rack, the doors must be installed
before installing the side panels.
1. Remove and save four screws from both top and bottom of
rack front. (See Figure 1)
Figure 1
2. Add top door support (C) and lower door support (D) to rack
front. (See Figure 4)
3. Attach door supports using eight screws removed in Step 1.
Figure 2
IMPORTANT ! : If the door is to be attached with the pull-
ring handle on the right side, the two nuts and grounding
wire already installed on the door must be removed and
reinstalled on the opposite end of the door before the
door is installed. The grounding wire should be on the
BOTTOM of the installed door. (See Figure 3)
Figure 3
4. Rotate two spring handles (one at bottom and one at top) on
inside of door. (See Figure 4)
Figure 4
x 8
1
(NS1D12F shown)
3
x 8
(NS1D12F shown)
(C)
(D)
Move to
grounding
screw
Move two nuts
and grounding wire
NOTE: Door will
be flipped before
installation.
4
5
Lower
spring
handle
Upper
spring
handle
(View from back of door)
Installation Instructions NS1D12-20-28-36-41
5
5. Pull down on upper spring handle, and push up on lower
spring handle.
6. Insert door into rack, aligning the spring handle ends with
the holes in the door support at top and bottom of rack. (See
Figure 5)
Figure 5
7. Push spring handle end into door supports, and re-latch
spring handle.
8. Determine location for door catch (B) by matching up
handle cut-out in door with correct position on rack. (See
Figure 6)
Figure 6
9. Add door catch (B) to rack rail using two 1/4-20 x 5/8"
screws (E) and two 1/4-20 lock nuts (F). (See Figure 7)
Figure 7
10. Loosen screw in lower door support, attach door grounding
wire, and tighten screw to finish connection. (See Figure 8)
Figure 8
6
Door
support
Door
Spring
handle end
8
9
(E) x 2
(F) x 2
(B)
x 1
10
NS1D12-20-28-36-41 Installation Instructions
6
Figure 9
DANGER: IMPROPER WIRING CAN LEAD TO DEATH
OR SEVERE PERSONAL INJURY! Grounding must be
installed by qualified personnel using a UL Recognized No.
12AWG Green and Yellow grounding wire connected to
grounding lug on rack.
(inside view of door)
Grounding screw and nut
installed at factory
affixed adjacent to grounding terminal.
Earthing symbol IEC 60417 No. 5019
Location of
grounding
lugs
Installation Instructions NS1D12-20-28-36-41
7
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
NS1D12-20-28-36-41 Installation Instructions
Chief Manufacturing, a products divi-
sion of Milestone AV Technologies
8821-002016 Rev02
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief NS1D20P Installation guide
- Category
- Rack accessories
- Type
- Installation guide
Chief NS1D20P is a rack door accessory designed for use with S1 racks. It features a perforated design for ventilation and enhanced airflow, ensuring optimal performance of your rack-mounted equipment. The door is easy to install and remove, providing convenient access to your equipment for maintenance or troubleshooting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief NS1S1223 Installation guide
-
Chief NE1D36S Installation guide
-
-
-
-
-
-
-
Chief CMS490 Installation guide
-