Alphard AAB-1200.2D Two-Channel Amplifier Owner's manual

Brand: Alphard

Model: AAB-1200.2D Two-Channel Amplifier

Type: Owner's manual

Alphard AAB-1200.2D Two-Channel Amplifier offers superb loudness without compromising on sound quality. It features two channels with a minimum impedance of 1 Ohm, producing 580 Watts RMS per channel. Bridgeable to 2 Ohms, it delivers a massive 2420 Watts RMS. With a frequency response of 15Hz-20kHz and adjustable crossover, it provides versatility for various audio setups. This high-quality amplifier ensures reliable performance and enhances your car audio experience.

TWO-CHANNEL AMPLIFIER

ДВУХКАНАЛЬНЫЙ УСИЛИТЕЛЬ

HTTPS://ALPHARD.AUDIO

AAB-1200.2D CLASS D

1. Before installing the ampliﬁer disconnect the battery from the electrical system.

2. To connect the ampliﬁer it is necessary to stretch the power cable from the location of the battery to the place of installation

of the ampliﬁer. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the

power cables)

3. Connect the power supply with the correct polarity. Connect all (+) terminals of the ampliﬁer to the cables stretching from

the positive terminal of the battery and all (-) terminals of the ampliﬁer – to the cables stretching from the negative terminal of the

battery.

4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of

the power cable to the holder after connecting the other end to the ampliﬁer. Do not install the fuse(s).

5. Route all signal cables next to each other and separately from the power cables.

6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.

7. To connect the power wire supply is necessary to use special power cables.

8. Fasten the ampliﬁer properly when installing it in the vehicle. If the component is disconnected during driving, it may cause

serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the ampliﬁer directly to the

metal it can lead to distorsions at the signal outputs.

9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.

Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the

light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive

terminal of the battery.

When properly connected, the bulb must brieﬂy light up and go out. Now you may connect the positive lead to the (+) of the

battery. If the light does not go out, then something is wrong. This will prevent damage to the ampliﬁer in case of reverse polarity

and unwanted sparks when connecting. Install the rest of the fuses.

10. To activate the ampliﬁer, it is necessary to apply the positive potential of 12 volts to the control input of the ampliﬁer (REM

IN) through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU).

11. LED indicator on front of the ampliﬁer turns blue to indicate that the ampliﬁer is turned on. If the indicator does not light

up see chapter "Possible faults and their solutions" for more information.

12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the

sensitivity level of the ampliﬁer up until you hear distortions.

Thank you for purchasing of this Deaf Bonce product! Our company is committed to the creation of extremely loud sound

systems with no loss of quality.

To ensure proper use, please carefully read through this manual before using this product. It is especially important that you

read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.

1-8 Ohm 1-8 Ohm

Caution!!! The minimum permissible connection load impedance at every single channel is 1 ohm.

For model AAB-1200.2D the operating voltage is 9-15V.

Caution!!! The minimum permissible connection load impedance for bridged connection is 2 ohm.

For model AAB-1200.2D the operating voltage is 9-15 V.

min. 2 Ohm

no more than 40 cm

REM IN

5/FL

4 Ohm 8 Ohm

Voice coil Total impedance

8 Ohm 16 Ohm

1 2 3 4 5 6 7

REM IN

14 15 16

16. CLIP-LED on the clip (yellow)

(yellow)

4 Ohm 12 Ohm

Voice coil Total impedance

8 Ohm 24 Ohm

4 Ohm 16 Ohm

Voice coil Total impedance

8 Ohm 32 Ohm

4 Ohm 2 Ohm

Voice coil Total impedance

8 Ohm 4 Ohm

4 Ohm 1.33 Ohm

Voice coil Total impedance

8 Ohm 2.66 Ohm

4 Ohm 1 Ohm

Voice coil Total impedance

8 Ohm 2 Ohm

4 Ohm 4 Ohm

Voice coil Total impedance

8 Ohm 8 Ohm

Deaf Bonce ampliﬁers are high-quality and technically perfect products. The problems often arise due to improper use, faulty

connection of components or lack of power supply of the on-board network.

1) The ampliﬁer does not turn on.

Problem solution: Check all the contacts and the presence of 9-15 V at the ampliﬁer terminals. Check whether the control input

of the ampliﬁer "REM IN" receives the positive potential of +12 V.

2) Power turns on, but goes into protection (protection indicator lights up)

Problem solution: Check if there is a short circuit (fault) on the ampliﬁer output which is connected to the speakers or

subwoofers. Make sure that commutation of the voice coils of the subwoofer is correct. The rated impedance of the voice coils

should not be lower than the permissible rated load impedance of the ampliﬁer. Check the supply voltage of the ampliﬁer. It must

be within the range of 9-15 V.

3) The ampliﬁer turns on but at a high volume it goes in to protection. Problem solution: The ampliﬁer may lack power. Make

sure that the rated current of the alternator and the battery capacity is enough to power this ampliﬁer.

Check the ampliﬁer for overheating. Check the load impedance.

4) The ampliﬁer is turned on, but there is no sound from the speakers or subwoofer.

Problem solution: Check the connection of the ampliﬁer, the integrity of the interconnecting cable, HU, the speakers or the

subwoofer.

580 x 2

780 x 2

AAB-1200.2D

2420 х 1

15 - 1000

50 - 20 000

0-12

15 - 20 000

0.2 - 6

100

8 / 8.37

9-15

215 x 247 х 73.5

8.46 x 9.72 х 2.89

2 / 33.6

> 260

1210 x 2

1560 х 1

Yes

9 . B O X C O N T E N T S EN

1 1 . I N F O R M A T I O N O N D I S P O S A L O F T H E E L E C T R I C A L A N D

E L E C T R O N I C E Q U I P M E N T ( F O R T H E E U R O P E A N C O U N T R I E S W I T H

S E P A R A T E W A S T E C O L L E C T I O N )

1 0 . W A R R A N T Y A N D M A I N T E N A N C E I N F O

Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning

conditions.

While the product is under warranty, defective parts will be repaired or replaced at the manufacturer's discretion. The

defective product, along with notiﬁcation about it, must be returned to the dealer from which it was purchased together with the

warranty certiﬁcate duly ﬁlled in, . If the product is no longer under warranty, it will be complete with the original packaging

repaired at the current costs.

Our company does not undertake any liability for damages due to transportation. Our company does not take any

responsibility for: costs or loss of proﬁt due to the impossibility to use the product, other accidental or consequential costs,

expenses or damages suﬀered by the customer. Warranty according to laws in force. For more information visit our website and

carefully read warranty card.

The manufacturer reserves the right to change design and speciﬁcation without prior notice.

1. Ampliﬁer – 1 pc.

2. Owner's manual – 1 pc.

3. Warranty card – 1 pc.

4. Remote control – 1 pc.

5. Mounting Kit – 1 pc.

9. После завершения установки проверьте электропроводку системы и убедитесь в том, что все подключения были

выполнены правильно. Перед установкой предохранителя, отключите плюсовой кабель от АКБ, установите предохранитель

в держатель предохранителя. При помощи лампочки 12 В 21 Вт подключите плюсовой кабель к одному контакту лампочки,

а второй оставшийся контакт лампочки к плюсовой клемме АКБ.

При правильном подключении лампочка должна кратковременно загореться и погаснуть. Теперь можно подключить

плюсовой кабель к + АКБ. Если лампочка не гаснет, значит что то сделано неправильно. Это позволит избежать выхода из

строя усилителя при переполюсовке и нежелательных искр при подключении. Установите оставшиеся предохранители.

10. Для включения усилителя, необходимо на управляющий вход усилителя (REM IN) подать положительный потенциал

+12 В через тумблер , либо соответствующий управляющий выход (REMOTE OUT) с головного устройства (ГУ).

11. Индикатор LED на передней панели усилителя загорится синим показывая, что усилитель включен. В случае если

индикатор не загорелся перейдите в раздел «Возможные неисправности и их решения» для получения дополнительной

информации.

12. Калибровка уровня звука производится путем настройки уровня громкости источника на 3/4 его максимального

уровня; затем, путем регулировки уровня входной чувствительности усилителя до тех пор, пока Вы не услышите искажения.

Внимание!!! Минимально допустимое сопротивление при поканальном включении - 1 Ом на каждый из

каналов усилителя. Для модели AAB-1200.2D рабочее напряжение составляет 9-15 В.

1-8 Ohm 1-8 Ohm

Внимание!!! Минимально допустимое сопротивление для мостового включения - 2 Ом.

Для модели AAB-1200.2D рабочее напряжение составляет 9-15 В.

мин. 2 Ом

Аккумулятор

не более, чем 40 см

Предохранитель

5/FL

1 2 3 4 5 6 7

REM IN

1. INPUT – вход сигнала, линейные входы RCA

14 15 16

16. CLIP – индикатор по клиппу (желтый)

(желтый)

Page is loading ...

Alphard AAB-1200.2D Two-Channel Amplifier Owner's manual

Brand: Alphard

Model: AAB-1200.2D Two-Channel Amplifier

Type: Owner's manual

Download PDF

report

in other languages

русский: Alphard AAB-1200.2D Two-Channel Amplifier Инструкция по применению

Alphard AAB-1200.2D Two-Channel Amplifier Owner's manual

Alphard AAB-1200.2D Two-Channel Amplifier Owner's manual

in other languages

Related papers

Other documents