Sony SLV-SX730N User manual

Brand: Sony

Model: SLV-SX730N

Category: Cassette players

Type: User manual

3-081-623-11 (1) GB

Video Cassette

Recorder

Operating Instructions

SLV-SE830N

SLV-SE730N

SLV-SX730N

SLV-SE630N

SLV-SE430K

PA L

WARNING

To prevent fire or shock hazard, do not expose the

unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

Mains lead must only be changed at a qualified

service shop.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz.

Check that the unit’s operating voltage is

identical with your local power supply.

• If anything falls into the cabinet, unplug the unit

and have it checked by qualified personnel before

operating it any further.

• The unit is not disconnected from the mains as

long as it is connected to the mains, even if the

unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not

intend to use it for an extended period of time. To

disconnect the cord, pull it out by the plug, never

by the cord.

• To prevent fire or shock hazard, do not place

objects filled with liquids, such as vases, on the

apparatus.

Installing

• Do not install this equipment in a confined space

such as a book or similar unit.

• Allow adequate air circulation to prevent internal

heat buildup.

• Do not place the unit on surfaces (rugs, blankets,

etc.) or near materials (curtains, draperies) that

may block the ventilation slots.

• Do not install the unit near heat sources such as

radiators or air ducts, or in a place subject to

direct sunlight, excessive dust, mechanical

vibration or shock.

• Do not install the unit in an inclined position. It is

designed to be operated in a horizontal position

only.

• Keep the unit and cassettes away from equipment

with strong magnets, such as microwave ovens or

large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a

warm location, moisture may condense inside the

VCR and cause damage to the video head and

tape. When you first install the unit, or when you

move it from a cold to a warm location, wait for

about three hours before operating the unit.

Caution

Television programmes, films, video tapes and other

materials may be copyrighted. Unauthorized

recording of such material may be contrary to the

provisions of the copyright laws. Also, use of this

recorder with cable television transmission may

require authorization from the cable television

transmitter and/or programme owner.

Compatible colour systems

This VCR is designed to record using the PAL (B/G

or D/K) or MESECAM (B/G or D/K) colour system

and play back using the PAL (B/G or D/K) or

MESECAM (B/G or D/K) and NTSC 4.43 colour

systems. Recording of video sources based on other

colour systems cannot be guaranteed.

HOWVIEW is a registered trademark of Gemstar

Development Corporation. The S

HOWVIEW system

is manufactured under license from Gemstar

Development Corporation.

Table of contents

Getting Started

Table of contents

Getting Started

4 Index to parts and controls

11 Step 1 : Unpacking

12 Step 2 : Setting up the remote

commander

16 Step 3 : Connecting the VCR

20 Step 4 : Setting up the VCR with

the Auto Set Up function

23 Step 5 : Selecting the TV

system

24 Setting the clock

26 Downloading the TV tuner’s preset

data

(SLV-SE830N, SE730N and

SX730N only)

27 Selecting a language

28 Presetting channels

31 Changing/disabling programme

positions

36 Setting the Canal Plus decoder

Basic Operations

39 Playing a tape

42 Recording TV programmes

46 Recording TV programmes using

the Dial Timer

(SLV-SE830N only)

51 Recording TV programmes using

the ShowView

system

(SLV-SE830N, SE730N and

SX730N only)

55 Recording TV programmes using

the timer

Additional Operations

58 Playing/searching at various speeds

60 Setting the recording duration time

61 Checking/changing/cancelling

timer settings

63 Recording stereo and bilingual

programmes

(not available on SLV-

SE430K

)

66 Searching using the index function

(not available on SLV-SE430K)

68 Adjusting the picture

69 Reducing the VCR’s power

consumption

70 Changing menu options

Editing

72 Connecting to a VCR or stereo

system

74 Basic editing

75 Audio dubbing

(SLV-SE830N only)

Additional Information

76 Troubleshooting

80 Specifications

82 Index

Back Cover

Quick Start Guide

Index to parts and controls

Getting Started

Index to parts and controls

Refer to the pages indicated in parentheses ( ) for details.

Front panel

For SLV-SE830N

A ?/1 (on/standby) switch

B Remote sensor (12)

C Tape compartment

D A (eject) button (39)

E m (rewind) button (39) (58)

F Shuttle ring (58)

G H (play) button* (39) (58)

H M (fast-forward) button (39) (58)

I JOG button (58)

J REC z (record) button (43) (60)

(74)

K x (stop) button* (22) (39) (74) (75)

L X (pause) button (39) (50) (74) (75)

M PROGRAM +/– buttons* (47) (59)

(68)

N DIAL TIMER (46)

O AUDIO DUB button (75)

P t LINE-2 L (left) o R (right)

jacks (covered)* (72) (73) (75)

How to open the jack cover

1 Press the bottom of the cover.

2 Hook your finger on the top edge of the

cover and pull it open.

* The

H (play), x (stop) and

PROGRAM + buttons and jack cover

have a tactile dot.

Getting Started

Index to parts and controls

For SLV-SE730N, SX730N and SE630N

A ?/1 (on/standby) switch

B Remote sensor (12)

C Tape compartment

D A (eject) button (39)

E m (rewind) button (39) (58)

F H (play) button* (39) (58)

G M (fast-forward) button (39) (58)

H REC z (record) button (43) (60)

(74)

I x (stop) button* (22) (39) (74) (75)

J X (pause) button (39) (74) (75)

K PROGRAM +/– buttons* (59) (68)

* The H (play), x (stop) and

PROGRAM + buttons have a tactile dot.

continued

Index to parts and controls

For SLV-SE430K

A ?/1 (on/standby) switch

B A (eject) button (39)

C Remote sensor (12)

D Tape compartment

E m (rewind) button (39) (58)

F H (play) button* (39) (58)

G M (fast-forward) button (39) (58)

H REC z (record) button (43) (60)

(74)

I x (stop) button* (22) (39) (74) (75)

J X (pause) button (39) (74) (75)

K PROGRAM +/– buttons* (59) (68)

* The H (play), x (stop) and

PROGRAM + buttons have a tactile dot.

Getting Started

Index to parts and controls

Display window

For SLV-SE830N, SE730N and SX730N

A Tape indicator

B VIDEO indicator (17) (43)

C Time counter/clock/line/programme

position indicator (40) (42) (74)

D (smartlink) indicator (18)

E TV indicator (45)

F STEREO indicator (63)

G Tape speed indicators (42)

H Timer/recording indicator (43) (48)

(53) (56)

For SLV-SE630N and SE430K

A Tape indicator

B Time counter/clock/line/programme

position indicator (40) (42) (74)

C Timer indicator (48) (53) (56)

D Recording indicator (43)

E STEREO indicator* (63)

F VIDEO indicator (17) (43)

G Playback indicator

* not available on SLV-SE430K

678

continued

Index to parts and controls

Rear panel

For SLV-SE830N, SE730N, SX730N and SE630N

For SLV-SE430K

A (in from antenna) connector (16)

(17)

B LINE-3 (DEC/EXT) connector*

LINE-2 (DEC/EXT) connector*

(19) (36) (73)

C Mains lead (16) (17)

D AUDIO (OUT/SORTIE) R/D (right)

L/G (left) jacks*

(19)

E LINE-1 (EURO AV) connector (17)

(36) (72)

F (out to tv) connector (16) (17)

SLV-SE830N

SLV-SE730N, SX730N, SE630N and

SE430K

not available on SLV-SE630N

Getting Started

Index to parts and controls

Remote commander

A Z (eject) button (39)

B (wide) button (for TV) (14) (15)

C DISPLAY button (14) (40) (43)

D COUNTER/REMAIN button (43)

E Programme number buttons*

(13)

(44)

F - (ten’s digit) button (13) (44)

G / (Teletext) button (for TV)*

(14)

H 2 (volume) +/– buttons (for TV)

(13)

I a TV power on/TV mode select

button

(for TV)*

(13)

J z REC (record) button (43) (60)

K SP (Standard Play)/LP (Long Play)

button (42)

L MENU button (24) (61)

M X (pause)/M button (24) (39)

x (stop)/m button (24) (39)

m (rewind)/< button (24) (39)

(58)

M (fast-forward)/, button (24)

(39) (58)

H (play)/OK button*

(24) (39)

(58)

The H (play), AUDIO MONITOR,

number 5 and PROG + buttons have a

tactile dot.

SLV-SE830N only

123

456

789

continued

Index to parts and controls

N [TV] / [VIDEO] remote control switch

(12)

O ?/1 (on/standby) switch (13) (14)

(53)

P AUDIO MONITOR button*

(14)

(64)

Q t TV/VIDEO button (13) (17) (43)

R CLEAR button (40) (52) (61)

S INPUT SELECT button (42) (56)

(74)

T PROG (programme) +/– buttons*

(13) (42)

c ⁄ C Teletext page access buttons

(for TV)*

(14)

U y SLOW button*

(58)

V ×2 button*

(58)

W ./> (index search)

buttons*

(66)

X TIMER button (51) (55)

The H (play), AUDIO MONITOR,

number 5 and PROG + buttons have a

tactile dot.

SLV-SE830N only

not available on SLV-SE430K

FASTEXT buttons (for TV)

(SLV-SE830N only)

123

456

789

Getting Started

Unpacking

Step 1 : Unpacking

Check that you have received the following items with the VCR:

• Remote commander

• R6 (size AA) batteries

• Aerial cable

Check your model name

The instructions in this manual are for the 5 models: SLV-SE830N, SE730N,

SX730N, SE630N and SE430K. Check your model name by looking at the rear

panel of your VCR.

SLV-SE830N is the model used for illustration purposes. Any difference in

operation is clearly indicated in the text, for example, “SLV-SE830N only.”

Setting up the remote commander

Step 2 : Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries

by matching the + and – on the

batteries to the diagram inside the

battery compartment.

Insert the negative (–) end first,

then push in and down until the

positive (+) end clicks into

position.

Using the remote

commander

You can use this remote

commander to operate this VCR

and a Sony TV. Buttons on the

remote commander marked with a

dot (•) can be used to operate your

Sony TV. If the TV does not have

the symbol near the remote

sensor, this remote commander

will not operate the TV.

To operate Set [TV] / [VIDEO] to

the VCR [VIDEO] and point at the remote sensor at the VCR

a Sony TV [TV] and point at the remote sensor at the TV

123

456

789

Remote sensor

[TV] /

[VIDEO]

Getting Started

Setting up the remote commander

TV control buttons

To Press

Set the TV to standby mode ?/1

Select an input source: aerial in or line in t TV/VIDEO

Select the TV’s programme position Programme number buttons,

-, PROG +/–

Adjust the volume of the TV 2 +/–

Switch to TV (Teletext off)*

a (TV)

PROG +/–/

c ⁄ C

2 +/–

123

456

789

Programme

number

buttons

DISPLAY

?/1

t TV/VIDEO

AUDIO MONITOR

FASTEXT buttons

continued

Setting up the remote commander

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery together with an old one.

• Do not use different types of batteries together.

• Some buttons may not work with certain Sony TVs.

SLV-SE830N only

not available on SLV-SE430K

Controlling other TVs with the remote commander

(SLV-SE830N only)

The remote commander is preprogrammed to control non-Sony TVs. If your

TV is listed in the following table, set the appropriate manufacturer’s code

number.

* These buttons may not work with all TVs.

Switch to Teletext*

/ (Teletext)

Select the sound*

AUDIO MONITOR

Use FASTEXT*

FASTEXT buttons

Call up the on-screen display

DISPLAY

Change the Teletext page*

c ⁄ C

Switch to/from wide mode of a Sony wide TV (For

other manufactures’ wide TVs, see “Controlling

other TVs with the remote commander (SLV-

SE830N only)” below.)

(wide)

Set [TV] / [VIDEO] at the top of the remote commander to [TV].

Hold down ?/1, and enter your TV’s code number using the programme

number buttons. Then release ?/1.

Now you can use the following TV control buttons to control your TV:

?/1, t TV/VIDEO, programme number buttons, - (ten’s digit),

PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,

(wide)*, MENU*,

M/m/</,*, and OK*.

To Press

Getting Started

Setting up the remote commander

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until

you find the one that works with your TV.

To switch to wide mode, see the footnotes below this table for the applicable

code numbers.

Press (wide) to switch the wide picture mode on or off.

Press (wide), then press 2 +/– to select the wide picture mode you want.

Press (wide). The menu appears on the TV screen. Then, press M/m/</, to

select the wide picture you want and press OK.

Tip

• When you set your TV’s code number correctly while the TV is turned on, the TV

turns off automatically.

Notes

• If you enter a new code number, the code number previously entered will be

erased.

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• When you replace the batteries of the remote commander, the code number may

change. Set the appropriate code number every time you replace the batteries.

Manufacturer Code number

Sony

01*

, 02

Akai 68

Ferguson 52

Grundig

10*

, 11*

Hitachi 24

JVC 33

Loewe 45

Mivar 09, 70

NEC 66

Nokia

15, 16, 69*

Panasonic

17*

, 49

Philips

06*

, 07*

, 08*

Saba 12, 13

Samsung 22, 23

Sanyo 25

Sharp 29

Telefunken 36

Thomson

43*

Toshiba 38

Manufacturer Code number

Connecting the VCR

Step 3 : Connecting the VCR

If your TV has a Scart (EURO-AV) connector, see page 17.

If your TV does not have a Scart (EURO-AV) connector

Note

• When you connect the VCR and your TV only with an aerial cable, you have to

tune your TV to the VCR (see page 20).

Disconnect the aerial cable from your

TV and connect it to on the rear

panel of the VCR.

Connect of the VCR and the aerial

input of your TV using the supplied

aerial cable.

Connect the mains lead to the mains.

Mains lead

AERIAL IN

to mains

Aerial cable (supplied)

: Signal flow

Getting Started

Connecting the VCR

If your TV has a Scart (EURO-AV) connector

Disconnect the aerial cable from

your TV and connect it to on

the rear panel of the VCR.

Connect of the VCR and the

aerial input of your TV using the

supplied aerial cable.

Connect LINE-1 (EURO AV) on

the VCR and the Scart (EURO-

AV) connector on the TV with the

optional Scart cable.

This connection improves picture

and sound quality. Whenever you

want to watch the VCR picture,

press t TV/VIDEO to display

the VIDEO indicator in the

display window.

Connect the mains lead to the mains.

Mains lead

LINE-1

(EURO AV)

AERIAL IN

Scart

(EURO-AV)

to mains

Aerial cable (supplied)

: Signal flow

Scart cable (not supplied)

continued

Connecting the VCR

About the SMARTLINK features (not available on SLV-SE630N and

SE430K)

If the connected TV complies with

SMARTLINK, MEGALOGIC*

EASYLINK*

, Q-Link*

, EURO

VIEW LINK*

, or T-V LINK*

, this

VCR automatically runs the

SMARTLINK function after you complete the steps on the previous page

(the indicator appears in the VCR’s display window when you turn on the

TV). You can enjoy the following SMARTLINK features.

• TV Direct Rec

You can easily record what you are watching on the TV when the VCR is

turned on. For details, see “Recording what you are watching on the TV

(TV Direct Rec) (not available on SLV-SE630N and SE430K)” on page

45.

• One Touch Play

With One Touch Play, you can start playback automatically without turning

on the TV. For details, see “Starting playback automatically with one

button (One Touch Play) (not available on SLV-SE630N and SE430K)” on

page 41.

• One Touch Menu

When the VCR is turned on, you can turn on the TV, set the TV to the

video channel, and display the VCR’s on-screen display automatically by

pressing MENU on the remote commander.

• One Touch Timer

When the VCR is turned on, you can turn on the TV, set the TV to the

video channel, and display the timer recording menu (the TIMER

PROGRAMMING menu or the SHOWVIEW menu) automatically by

pressing TIMER on the remote commander.

You can set which timer recording menu is displayed using TIMER

METHOD in the EASY OPERATION menu (see page 71).

• NexTView Download

You can easily set the timer by using the NexTView Download function on

your TV. Please refer to your TV’s instruction manual.

“MEGALOGIC” is a registered trademark of Grundig Corporation.

“EASYLINK” is a trademark of Philips Corporation.

“Q-Link” is a trademark of Panasonic Corporation.

“EURO VIEW LINK” is a trademark of Toshiba Corporation.

“T-V LINK” is a trademark of JVC Corporation.

Note

• Not all TVs respond to the functions above.

Getting Started

Connecting the VCR

Additional connections

To a stereo system (not

available on SLV-SE630N

and SE430K)

You can improve sound

quality by connecting a

stereo system to the AUDIO

R/D L/G jacks as shown on

the right.

To a satellite or digital

tuner with Line Through

Using the Line Through

function, you can watch

programmes from a satellite

or digital tuner connected to

this VCR on the TV even

when the VCR is turned off.

When you turn on the

satellite or digital tuner, this

VCR automatically sends the

signal from the satellite or

digital tuner to the TV

without turning itself on.

Notes

• The Line Through function will not operate properly if POWER SAVE in the

USER SET menu is set to ECO2. Set POWER SAVE to OFF or ECO1 to ensure

proper operation (see page 69).

• You cannot watch programmes on the TV while recording unless you are recording

a satellite or digital programme.

• This function may not work with some types of satellite or digital tuners.

• When the VCR is turned off, set the TV to the video channel.

SLV-SE830N

SLV-SE730N, SX730N, SE630N and SE430K

Connect the satellite or digital tuner to the LINE-3 (DEC/EXT)*

LINE-2 (DEC/EXT)*

connector as shown above.

Turn off the VCR.

To watch a programme, turn on the satellite or digital tuner and the TV.

Audio cable (not supplied)

AUDIO R/D L/G

LINE IN

: Signal flow

Scart cable (not supplied)

LINE-3 (DEC/EXT)*

LINE-2 (DEC/EXT)*

LINE

OUT

: Signal flow

Setting up the VCR with the Auto Set Up function

Step 4 : Setting up the VCR with the Auto

Set Up function

Before using the VCR for the first time, set up the VCR using the Auto Set Up

function. With this function, you can set the language for the on-screen display, TV

channels, guide channels for the ShowView system*, and VCR clock* automatically.

Turn on your TV and set it to the video channel.

If your TV does not have a Scart (EURO-AV) connector, tune the

TV to channel 32 (the initial RF channel for this VCR). Refer to

your TV manual for TV tuning instructions. If the picture does not

appear clearly, see “To change the RF channel” on page 22.

Connect the mains lead to the

mains.

The VCR automatically turns on,

and the language abbreviations

appear on the TV screen.

The abbreviations of the

languages are as follows:

Press M/m/</, to select the language abbreviation from the table

in step 2, then press OK.

The message for the Auto Set Up function appears.

EXIT MENU:OK:SET

SELECT

Abbreviation Country Language

CZ Czecho Czech

HU Hungary Hungarian

PL Poland Polish

SK Slovakia Slovak

TR Turkey Turkish

RU Russia Russian

Page is loading ...

Sony SLV-SX730N User manual

Brand: Sony

Model: SLV-SX730N

Category: Cassette players

Type: User manual

Download PDF

report

Sony SLV-SX730N User manual

Sony SLV-SX730N User manual

Related papers

Other documents