Battery Daddy Storage system User manual

Brand
Battery Daddy
Model
Storage system
Type
User manual

This manual is also suitable for

USING YOUR BATTERY DADDY:
™
Thanks for your purchase of Battery Daddy™ - the new, compact
and portable way to organize, store and protect your batteries!
Battery Daddy™ uses both sides to store all types of different
batteries, even coin size. Best of all, it packs an amazing 180
batteries yet takes up the space of a laptop — perfect in any
cabinet, drawer or shelf.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: Place batteries with + (positive) side facing cover.
The FRONT side can store various sizes of batteries:
• 22 AAs
• 70 AAAs
• (8) 9-Volts
• 12 Button Cells
• 10 Cs
• 8 Ds
The BACK side can store AA batteries
(plus AAAs in the handle area)
• 54 AAs • 2 AAAs
Front Back
Batteries Not Included
LOW
B
U
T
T
O
N
B
A
T
T
R
E
P
L
A
C
E
G
O
O
D
9VOLT
PP3 MN1604
MINI
CELL
AAAHP16MN2400
AAAHP7 . MN1500
C.HP11.MN1400
D.HP2.MN1300
BATTERY TESTER
1.5VOLT
2
LOW
B
U
T
T
O
N
B
A
T
T
R
E
P
L
A
C
E
G
O
O
D
9VOLT
PP3 MN1604
MINI
CELL
AAAHP16MN2400
AAAHP7 . MN1500
C.HP11.MN1400
D.HP2.MN1300
BATTERY TESTER
1.5VOLT
LOW
B
U
T
T
O
N
B
A
T
T
R
E
P
L
A
C
E
G
O
O
D
+
MINI
CELL
LOW
B
U
T
T
O
N
B
A
T
T
R
E
P
L
A
C
E
G
O
O
D
+
MINI
CELL
3 4
9VOLT
PP3 MN1604
+
_
1 2
1
LOW
B
U
T
T
O
N
B
A
T
T
R
E
P
L
A
C
E
G
O
O
D
9VOLT
PP3 MN1604
MINI
CELL
AAAHP16MN2400
AAAHP7 . MN1500
C.HP11.MN1400
D.HP2.MN1300
BATTERY TESTER
1.5VOLT
USING THE BATTERY TESTER:
Glide the red slide down to fit the
battery size you want to test.
Insert the battery + (positive) side down facing red slide
and – (negative) side up facing top of tester. Be sure both
ends of battery are in contact with the silver contact points.
1. Find 9-Volt marking on top of tester. Line up the –
(negative) and + (positive) ends of the battery with the
matching contact points on tester.
2. Meter will display GOOD, LOW, or REPLACE.
Push red slide up until battery is held in place. Meter will display GOOD, LOW, or REPLACE.
For all batteries except 9-Volt:
For 9-Volt Batteries:
Distributed by
©



  • Page 1 1
  • Page 2 2

Battery Daddy Storage system User manual

Brand
Battery Daddy
Model
Storage system
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents