Sera KOI Professional 12000 User manual

Brand: Sera

Model: KOI Professional 12000

Type: User manual

This manual is also suitable for

KOI Professional 12000 Pond Filter

Sera KOI Professional 12000 Pond Filter is a multi-step purification system for garden ponds with a volume of up to 12,000 liters, designed for ponds with high fish stock density, as is often the case with Koi ponds. It features a highly effective UV-C system for removing floating algae, thread algae, and pathogens, as well as a split sieve for mechanical water purification, a fine mesh filter sponge for removing algae during blooms, and a biological water purification chamber with sera siporax pond filter medium for breaking down pollutants.

Information for use

Please read these instructions carefully and keep for future use.

When forwarding this unit to third parties, this information for use

is also to be handed over.

Thank you for choosing the sera KOI Professional 12000 Pond Filter.

Please check whether all components of this high quality system, which

includes glass parts, have arrived at your place without damages before

we continue by presenting you the installation and the functions of this

novel pond filter system. You will find further information about this in

the warranty conditions.

General notes

The sera KOI Professional 12000 Pond Filter is a multi-step purifica-

tion system designed according to newest current act filter technology

findings. The system is divided into the following steps.

Step 1: Highly effective, newly developed UV-C system (1.6)

• Reliable removal of all kinds of floating algae (cloudy, green water)

• Reduction of thread algae and other algae

• Lasting removal of pathogens and bacterial water cloudiness

The UV-C System was specially designed for garden pond purposes

and consistently developed using newest technology. The PL 55 W UV-C

lamp is operated by an electronic ballast. The UV-C system is therefore

particularly energy saving and economical.

Please refer to the information for use of the sera pond UV-C-System

55 W for further information.

Step 2: Mechanical water purification – sludge removal

The split sieve (1.2) removes all particles larger than 0.2 mm. The sieved

particles get into the waste water chamber (2.9) via the split sieve, and

thus are removed from the biological cycle of the pond. Particles

trapped in sponges or other media decompose slowly there and thus

are still available as a nutrient source for the biological community in the

pond.

They can be easily removed along with other remainders via the waste

water removal valve (1.15) of the waste water chamber (2.9). The residue

obtained this way can now unfold its valuable nutrients, e.g. as a gar-

den fertilizer.

Step 3: Oxygen enrichment (2.5)

The water falls through pond filter body underneath the split sieve (2.4)

where it is enriched with oxygen from the air by swirling. This allows

converting all substances that were not removed mechanically under

aerobic conditions within the following biological breakdown step.

Step 4: Fine mesh algae filtration (2.6)

The sera fine mesh filter sponge (1.3) can be placed underneath the

split sieve, as to keep the pond clear and attractive even in times of

strong floating algae growth. However, this measure should be taken

only for a limited time, mainly during summer. The kit includes two filter

sponges that should be used in an alternating way.

Step 5: Biological water purification (2.13)

The water is evenly distributed by a Matala mat above the biofilter

chamber after dirt and algae have been removed, and flows onto the

sera siporax pond filter medium below.

Due to its chemical and physical material properties, the high perform-

ance biofilter medium sera siporax pond provides an ideal living envi-

ronment for the valuable pollutant removing bio cultures. The open pore

structure ensures ideal water current conditions for the micro organ-

isms, thus ensuring the biofilms are optimally supplied and pores do not

get clogged even after years of operation. sera siporax pond biologi-

cally cleans itself! At the same time, sera siporax pond is very resistant

against wear and tear and thus allows operation times of several years.

The biological performance capacity is outstanding: A single liter (one

US quart) of sera siporax pond has the same breakdown performance

as approx. 34 liters (9 US gal.) of ceramic material. In other words: It

provides enormously high breakdown performance with very little space

requirements. Also, it requires very little maintenance and will last for a

long time!

SAFETY PRECAUTIONS

Attention electrical shock! All electrical units must be disconnected

from the mains/power supply before conducting work at the sera KOI

Professional 12000 Pond Filter, the UV-C lamp, the pond pump as well

as all other work in and around the pond.

Attention UV radiation! Do not look into the eye damaging light of the

UV-C lamp. Switch off the lamp before cleaning or maintenance.

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

US KOI Professional 12000 Pond Filter

Application and application range

The sera KOI Professional 12000 Pond Filter is designed for ponds

with high fish stock density, as is often the case with Koi ponds, with a

volume of up to 12,000 liters (3,170 US gal./h).

The latest technical alteration is a filter sponge chamber (2.7) that allows

inserting a fine mesh filter sponge (2.6) easily and conveniently without

any tools. The fine mesh filter sponge can be used in times of strong al-

gae blooms as to keep the pond water clear also during this time.

The special overflow chute (2.8) makes sure the sera KOI Professional

12000 Pond Filter cannot clog even in case of a very dirty fine mesh fil-

ter sponge.

It is important that the fine mesh filter sponge is cleaned daily, as to re-

move trapped nutrients contained in algae and floating matter, from the

pond permanently.

The fine mesh filter sponge should be removed from the sera KOI Pro-

fessional 12000 Pond Filter when the water is clear again. The fine

mesh filter sponge is dimensioned in a way that it can be easily washed

out and cleaned by hand under running water.

Also, the waste water chamber (2.9) underneath the split sieve should

be checked regularly and cleaned if necessary.

Kit includes Item no.

sera KOI Professional 12000 Pond Filter 08309

1.1 Cover

1.2 Split sieve 200 μm

1.3 2 x Fine mesh filter sponge

1.4 Upper part

1.5 UV-C System installation area

1.6 UV-C System

1.7 Cover for bottom part

1.8 Matala mat

1.9 1 x 10 l/2 kg (1 x 4.4 lb.) sera siporax pond

1.10 Bottom part

1.13 sera sieve lifter

1.14 Variable hose connector 20/25/32/40 mm

(¾” / 1” / 1 ¼” / 1 ½”)

diameter with mounting

adapter

1.15 sera waste water removal valve

sera KOI Professional 12000 Pond Filter 08310

1.11 1 x sera pond pump PP 12000

1.12 sera pond hose 10 m (11 yd.)

Accessories (not included)

sera UV-C 55 W replacement lamp

sera pond hose Æ32 mm (

1 ¼”)

25 m (27.5 yd.), rolled up (1.12)

Parts list (fig. 2)

2.1 Water intake

2.2 Water intake chamber

2.3 Overflow to split sieve

2.4 Split sieve 200 µm

2.5 Aeration

2.6 Fine mesh filter sponge

2.7 Filter sponge chamber with grid for sponge placement

2.8 Overflow chute

2.9 Waste water chamber

2.10 sera waste water removal valve

2.11 Matala mat

2.12 Support for Matala mat

2.13 Biochamber

2.14 1 x 10 l/2 kg (1 x 4.4 lb.) sera siporax pond

2.15 Protection against running dry

2.16 Outlet opening

You will find the spare parts for the sera pond UV-C System 55 W and

the sera pond pump PP 12000 in the corresponding instructions for

use.

Assembly and operation

Complete every step (1. – 6.).

1. Location

The sera KOI Professional 12000 Pond Filter must be placed on one

level with the pond surface in a flat, horizontal position, allowing the wa-

ter to run back directly from the filter into the pond without water push-

ing back or counter pressure. Only a hose with max. 2 m (6.6 ft.) length

and the same diameter as the outlet may be connected to the filter out-

let (2.16). An artificial brook is suitable for directing the purified water

back into the pond in case you wish to place the filter in some distance

to the pond.

The position of the sera KOI Professional 12000 Pond Filter should be

chosen in a way that prevents knocking over the filter by pets, playing

children or the like.

The sera KOI Professional 12000 Pond Filter is not suitable for indoor

use.

2. Connection to pump

Check the diameter of your current hoses to the smallest diameter of the

hose connector. Smaller sections of the connector can be trimmed-

back with an (iron) saw to allow better flow with larger diameter hoses.

Before installing the hose connectors, always grease both O-rings with

the silicon oil included with the kit. Only then you may push them into

the opening up to the stop and fasten the screw cap.

For further information about putting sera pond pump PP 12000 or an-

other suitable pond pump in operation, please refer to the instructions

for use of the respective unit.

3. Connecting a sera pond UV-C System 55 W

You will find a detailed description about how to install the sera pond

UV-C System 55 W (1.6) to the sera KOI Professional 12000 Pond Fil-

ter in the information for use of the sera pond UV-C System 55 W.

4. Connecting the waste water removal valve (1.15)

If the waste water removal valve (2.10) is not yet installed at the side of

the split sieve (2.4), connect it with both seal rings, as shown in fig. 3.

You can screw the waste water removal valve (2.10) clockwise into its

counterpart held on the inside for this purpose. Screwing it on by hand

is sufficient. Fill the waste water chamber (2.9) with water underneath

the split sieve and check whether the waste water removal valve is wa-

ter proof.

5. Function control of the UV-C system: Wear protecting goggles

Please refer to the instructions for use of the sera pond UV-C System

55 W for this task.

6. Test run in case of connecting a UV-C system

Carry out a test run after having finished items 1 – 4.

Prior to using the sera pond UV-C-System 55 W, the fully installed unit

must be operated under normal operation conditions as expected later

on for at least 24 hours WITHOUT CONNECTING THE UV-C SYSTEM

TO THE POWER/MAINS SUPPLY, i.e. in simple flow operation connect-

ed to a pump, as to discover possible leaks in advance.

The water flow and pressure (pumping height) should match that of nor-

mal operation. Please refer to the instructions for use of the UV-C unit

for further information.

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

Maintenance and cleaning

a) Cleaning the split sieve

• Disconnect all electrical components from the mains/power supply

(UV-C system, pump, etc.) in and around the pond. Take off the cov-

er of the filter casing (aside the sera pond UV-C System 55 W).

• Place an empty bucket within reach. Remove all collected dirt and

sludge from the filter casing, preferably with water proof gloves.

• Now take out the split sieve (2.4). Wash the split sieve on both sides

using a hose. Particles stuck in the splits can carefully be removed

with a scrubbing brush. Do not use a wire brush or hard items to clean

the split sieve. The splits must not be damaged as to prevent the op-

timal purification effect of the sieve from being affected.

• Put the split sieve back into its holder after cleansing, the “arrow”

mark located at the bottom, i.e. in flow direction. The split sieve lifter

is simply placed on the top right or left. Put the filter chamber cover

(1.1) back on.

b) Cleansing the sera fine mesh filter sponge (2.6)

The sera fine mesh filter sponge must be washed out regularly and

thoroughly during periods of strong algae growth. Depending on the in-

tensity of floating algae growth, this may be required daily as to main-

tain the full purification performance of the pond filter system. In times

of low floating algae pollution, the pond filter should be operated with-

out the sera fine mesh filter sponge. The specially developed overflow

system provides efficient protection against the filter overflowing in case

you forgot washing out the sera fine mesh filter sponge.

c) Cleaning the Matala mat (2.11) and the bio chamber (2.13)

• Disconnect all electrical components from the mains/power supply

(UV system, pump, etc.) in and around the pond by pulling the mains

plug. Empty the upper part (1.4) [approx. 20 l (5.3 US gal.)], by loos-

ening the union nut between the UV-C system and the pond filter. Lift

the upper part of the filter casing (1.4) off the bottom part (1.10). Place

the upper part onto a plain surface and avoid knocking over the up-

per part. Be sure not to place the upper part on the cable connections

of the UV-C 55 W system or damage the UV-C 55 W system other-

wise.

• Now take the cover of the bottom part (1.7) off. Remove the Matala

mat (2.11). Rinse the Matala mat with a hose against the flow direc-

tion in the filter.

• The bio chamber (2.13) with sera siporax pond (2.14) is located un-

derneath the Matala mat. Remove the net and rinse it in a bucket with

lukewarm water. Do not use any detergents as to prevent the bacte -

rial flora from being destroyed. Only surface sludge must be removed

from sera siporax pond. The clear water chamber upstream of the

outlet opening (2.16) must remain free.

• Wipe out the empty bio chamber (2.13) with a soft sponge and rinse

it with water. Put sera siporax pond and the Matala mat back in

place. Put the upper part of the sera KOI Professional 12000 Pond

Filter back onto the bio chamber after cleansing. Switch on the pump

and put the UV-C system back into operation after 30 minutes.

SAFETY PRECAUTIONS

Warning: Dangerous ultraviolet radiation!

Never look directly into the special UV-C lighting (lamp) when it is operat -

ing (eye damage!).

Lamp function control through the two viewing glass panes at the top of

the UV-C casing or through the hose nozzle: Goggles (UV-C protecting

glass) provides suitable additional protection.

• The special sera UV-C lamp may be operated only inside the com-

pletely assembled sera pond UV-C System (please refer to direc-

tions for use for information about readiness to use). Every other use

may lead to severe skin and eye damage!

• Always keep UV units and UV-C lamps out of the reach of children!

• All electrical units in and around the pond must be disconnected from

the power/mains supply before conducting work at/in the pond and

on the sera KOI Professional 12000 Pond Filter.

• Operate unit only with an inserted fault current protection switch

(RCD or FI with a trip current of 30 mA).

• Do not operate if unit is submerged!

• Usage in or at swimming pools, walk-in ponds or swimming ponds is

not permitted!

• Never operate the UV-C system without water flow! First connect the

sera KOI Professional 12000 Pond Filter to a pump as described in

the instructions for use.

• For stabilizing its standing it may only be operated when the bottom

chamber is sufficiently filled, e.g. with sera siporax pond.

• Ensure that there is sufficient water flow through the sera pond UV-C

System before switching on the UV-C lamp. A minimum flow rate of

at least 2,000 l/h (530 US gal./h) up to 12,000 l/h (3,170 US gal./h) at

the maximum must be ensured also during operation.

• At the first sign of frost, disconnect and drain the sera pond UV-C

System, and store in a frost-free location (without water or water re-

mainders). We recommend thorough cleaning before winter storage.

• Frequent “ON/OFF” switching reduces the life expectancy of the UV-C

lamp.

• Ensure that the electrical plug of the switched-on unit is freely acces-

sible at all times.

• The test run according to the section “Assembly and operation” must

be carried out before putting the UV-C system into operation!

Also observe all safety advice provided in the instructions for use of the

included devices.

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

Troubleshooting list

Problem

Water is green. The sera KOI Professional

12000 Pond Filter is unable to make a

detectable improvement even after 14 days

Water is cloudy but not green, greenish

brown or yellowish green. The sera KOI

Professional 12000 Pond Filter does not

remove the cloudiness

Larger particles are in the outlet water

sera KOI Professional 12000 Pond Filter

runs over

Possible cause

UV-C lamp is faulty

Electronic ballast is faulty

UV-C lamp is too old

Underestimated pond size

Quartz glass sleeve of the UV-C system is

dirty

Clogged filter system

Fine mesh filter sponge is dirty

Cloudiness is not caused by algae but by

mineral particles (e.g., clay/loam components),

or humic substances (e.g., from leaves). Milky

white cloudiness can be caused by micro

organisms that require much stronger UV

irradiation to destroy them (occasionally

apparent after disease treatments).

In case cloudiness is not successfully

removed, the cause is often that the filter

material has been cleaned too frequently.

Split sieve is clogged

Split sieve has not been installed

Outlet of the sera KOI Professional 12000

Pond Filter is clogged

Outlet of the sera KOI Professional 12000

Pond Filter is located underneath the water

surface, and counter pressure builds up

Possible solution

Replace. Spare lamps are available from

specialized stores

Have the electronic ballast replaced by an

expert

Every UV-C lamp must be replaced after

approx. 5,000 hours of operation

Install another sera KOI Professional 12000

Pond Filter with pond UV-C System 55 W

Clean according to information for use

Check water flow and clean the sera KOI

Professional 12000 Pond Filter according

to the instructions, and/or clean the pump

Wash out fine mesh filter sponge. This may

be required daily in case of strong pollution

Lower the water flow through the UV-C

system considerably, if possible

(minimum = 50% of the lowest value of the

optimal water flow). Remove the source of

cloudiness if known. Replace pond water

with tap water by conducting several partial

water changes within a few days. Operate

UV-C system with low flow rate.

Additionally:

Insert fine mesh filter sponge and wash it

out regularly

Clean sera siporax pond only if there is

visible deposited sludge on the filter tubes

Clean according to the directions for use

Place split sieve with rubber seal into the

holder with the “arrow” mark located at the

bottom

Clean outlet according to the directions for

use

Place the sera KOI Professional 12000

Pond Filter level or above the water surface

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

Technical data

sera KOI Professional 12000 Pond Filter

Height approx. 92 cm (3 ft.)

Width approx. 40 cm (1.3 ft.)

Length approx. 83 cm (2.7 ft.)

pond pump PP 12000 Voltage 230 V ~ 50 Hz

Power uptake 165 W

Delivery amount 12,000 l/h

(3,170 US gal./h)

Delivery height

H max. 5.1 m (16.7 ft.)

UV-C System 55 W Voltage 230 V ~ 50 Hz

Power uptake 55 W

Spare parts

Fine mesh filter sponge

Small split sieve with rubber seal

sera waste water removal valve, small

Matala mat, small

sera siporax pond

Mounting adapter

Variable hose connector

Spare parts for the connected units can be found in the instructions for

use included with the respective units.

Warning

1. Children should be supervised to ensure that they do not play with

the appliance.

2. This appliance is not intended for us by persons (including children)

with reduced physical, sensory or mental capacities, or lack of expe-

rience and knowledge, unless they have been given supervision or in-

struction concerning use of the appliance by a person responsible for

their safety.

3. The pond pump and the UV-C lamp must not be used any longer but

have to be disposed of or repaired if the power/mains cord is dam-

aged.

Disposal of the unit:

Waste electrical and electronic equipment (WEEE) must not get in-

to domestic waste!

If ever the unit cannot be used anymore, the consumer is legally

obliged to hand in waste electrical and electronic equipment

(WEEE) separately from domestic waste, e.g. at a collection point of

his community/his district. This ensures that waste electrical and elec-

tronic equipment (WEEE) is expertly processed and that negative ef-

fects to the environment are avoided.

Therefore electrical and

electronic equipment bears the following symbol:

Manufacturer warranty:

When following the directions for use the sera KOI Professional 12000

Pond Filter will perform reliably. We are liable for the freedom from

faults of our products for 2 years beginning with the purchase date.

We are liable for complete flawlessness at delivery. Should usual wear

and tear occur by use as intended by us, this is not considered a defect.

Warranty claims are also excluded in this case. This especially refers to

the running unit (rotor, shaft bearings), the filter media and the hoses. Of

course, no legal claims are restricted or limited by this warranty.

Recommendation:

In every case of a defect we recommend that you consult the special-

ized retailer where you purchased the unit. He will be able to judge

whether it is actually a warranty case. In case of sending the unit to us

we will unnecessarily have to charge you for occurring costs.

Any liability because of contract breach is limited to intent or gross neg-

ligence. sera will be liable in case of slight negligence only in case of in-

juries to life, body and health, in case of essential contractual obliga-

tions and with binding liability according to the product liability code. In

that case, the extent of liability is limited to the replacement of contrac-

tually typically foreseeable damages.

The warranty conditions of the further units included in the set are also

valid. These are specified in the respective instructions for use.

Please note the additional warranty information (*).

Important warranty addendum (*):

•Running units that are worn, broken or stuck due to lime deposits

are a direct consequence of insufficient maintenance or improper

treatment. These and all subsequent damages are not covered by the

warranty. Often, these damages cannot be repaired.

•Broken rotor wings are caused by gravel or other larger, hard parti-

cles that have been sucked into the unit. These damages are not cov-

ered by warranty. Please always use the pump cover supplied with

the kit.

•Damage to the power/mains cord (e.g., by rodent bites, ice, garden

tools, will not be repaired by the manufacturer due to safety reasons.

(Reason: Moisture that has gotten into the cable often leads to corro-

sion and short-circuits in the motor later on.) Replacing the complete

cable is not possible. The pump must be discarded.

• Any damages of the cable are excluded from warranty.

• Glass damages caused by inappropriate treatment are excluded from

warranty.

• Transport damages must be claimed immediately upon having re-

ceived the product.

Warranty exclusion:

The sera KOI Professional 12000 Pond Filter is only designed for out-

door operation. Damages caused by water flowing out are not covered

by warranty.

Update 03.11US

Subject to technical alterations and errors

GmbH • Post Box 1466 • 52518 Heinsberg • Germany • Made in Europe

For natural garden ponds

US KOI Professional 12000 Pond Filter

1.1

1.2

1.3

1.4

2.1 2.3 2.42.2

2.8

2.5

2.6

2.7

2.16 2.15

2.11

2.122.132.14

2.9

2.10

1.7

1.6

1.5

1.8

1.15

1.9

1.10

1.11

1.12 1.13

1.14

Sera KOI Professional 12000 User manual

Brand: Sera

Model: KOI Professional 12000

Type: User manual

This manual is also suitable for

KOI Professional 12000 Pond Filter

Download PDF

report

Sera KOI Professional 12000 User manual

This manual is also suitable for

Sera KOI Professional 12000 User manual

Related papers

Other documents