Your 16Pot system
set-up guidelines
[email protected] I www.autopot-usa.com I +(1) 562 612 4182
16
At the end of your growing season, clean
the AQUAvalve using warm soapy water.
Using an old tooth brush will help.
The AQUAvalve is easily disassembled.
The top float will slide all the way across
and the bottom float is unclipped from its
pivoting position. The circular discs fitted to
the top float can also be removed by using
pliers to grip the raised point.
At this point is it advisable to remove the
silicones to avoid them being lost.
It is also handy to have a paper clip or
pipe cleaner to hand so that you can push
it through the AQUAvalve nozzle, this will
remove any lime scale build up that may
have occurred during the growing season.
Blowing through the AQUAvalve nozzle will
also help to remove any build up. Do not
under any circumstances use a drill & drill
bit to clear the AQUAvalve nozzle.
This will potentially damage the
AQUAvalve beyond repair.
Simple care
guidelines
[email protected] I www.autopot-usa.com I +(1) 562 612 4182
Ensuring that the AQUAvalve5 floods
and drains correctly
Care and maintenance
Making sure your AQUAvalve5 floods and
drains correctly is simply achieved and
only takes a few seconds.
Hold the AQUAvalve5 at eye level so that
you can see the silicone fitted to the top
float resting on the hole below it.
The silicone must create a tight seal when
touching the hole.
If it looks like it is not sitting parallel on the
hole below, simply lift the top float and
apply pressure to one side of the silicone,
drop the float and hold at eye level again.
Repeat the procedure if necessary.
11
2
2
3
4
Ensure the silicone is sitting parallel
on the hole below it. Hold at eye level
to check the position is correct
16Pot system contents
[email protected] I www.autopot-usa.com I +(1) 562 612 4182 If you require any guidance email - [email protected]
Advice
Plan views
and options
1Pot
dimensions
Advice
Using your front instruction sheet, repeat the module set up instructions for the number of trays.
Allow your plants to establish for 7-10 days before turning system on
1Pot setup
instructions
Suggested layout
• Pot up your plants, water through, then allow your plants to establish in the pots for a period of 7 to 10 days before
turning your system on. This will encourage a stronger and healthier root system.
• Always raise your reservoir/FlexiTank to a minimum of 6” above the highest AQUAvalve5 and re-fill the reservoir
FlexiTank when there is approx. 1/3 of the solution left – NEVER ALLOW THE RESERVOIR/FLEXITANK TO RUN EMPTY.
• With AQUAvalve5 systems mineral or organic fertilisers may be fed via the reservoir and pipework. Organic
fertilisers will require a water pump in the reservoir running for 15 mins every 2 hrs and cleaning of the reservoir,
pump, and filter each time the reservoir empties. Flush pipework with plain water every time the reservoir empties.
• Clean all substrate from the bottom and sides of the pots before placing in each tray. This will ensure your system is
clean from the start.
• Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles, coco/clay pebbles,
rockwool/clay pebbles.
¼" pipe
½" pipe
AQUAvalve
½" click-fit tank adaptor & filter
½" in-line tap
½" – ¼" cross connector
½" tee connector
60 gal
FlexiTank
System requires minimum
60 gal FlexiTank (supplied)
• 1x 60 gallon FlexiTank
• 1x 1/2” click-fit tank adaptor & filter
• 26ft of 1/2” pipe
• 2x 1/2” in-line tap
• 1x 1/2” tee connector
• 8x 1/2”-3/8” cross connector
• 16x 3/8” top hat grommet
• 16x 1Pot trays & lids
• 16x 3.9 gallon pot
• 16x AQUAvalve5
• 26ft of 3/8” pipe
• 16x Root Control Disc
60 gal
FlexiTank
25”
31.9”
13.8"
9.6"
10.2"
7.6"
11.8"
3.9 gal
pot
1
10
2
Put root control disc
in pot gold face up
5
Remove any slack in the
3/8” pipe by drawing
excess out of the tray.
3From outside of the module
tray push 3/8” top hat
grommet into the hole in
the module tray wall.
Thread approx 12” of
3/8” pipe into the tray
through the grommet.
Remove AQUAvalve collar
Push 3/8” pipe through
collar and attach to
AQUAvalve nozzle
Rescrew collar - DON’T
overturn... when you
feel it grip STOP
4
Fill pot with medium
and pot up plants.
Water through pot
and allow to drain
outside the tray.
Place pot in the
tray, make sure it is
CLEAN!
Place lid over valve
onto tray
9
According to the size of your system connect your
3/8” / 1/2” pipe to relevant fitting or tank...
7
Position tray
so it is level
6Align the ‘half moon’
section on the rear of
the AQUAvalve with the
‘T’ section in the tray.
Firmly push the
AQUAvalve onto the ‘T’.
8
Cut 3/8” / 1/2” pipe to
appropriate length
Pull
/
