IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a
combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the
supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in
the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product
acceptance by Authorities Having Jurisdiction.
This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material,
manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of
non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing.
Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc.
Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
This certificate is not evidence of current listing. To verify listing status, visit the IAPMO R&T
Product Listing Directory at pld.iapmo.org
Effective Date: March 2019 -Rev. 1/22/2020- Void After: March 2024
Product: Plumbing Fixture Fittings - Components File No. MC-8435
Issued To: Hain Yo Enterprises Co., Ltd
No. 102, Tien Tung Rd.
Hemei Township
Changhua, R.O.C. 508
Taiwan
Identification: Each fitting component shall bear permanent legible markings to identify the
manufacturer. This marking shall be the trade name, trademark, or other mark
known to identify the manufacturer. The product shall also bear all other
markings required by the standard. The marking shall be applied so as to be
visible after installation. The product or packaging shall also bear the
cUPC® certification mark along with the term "COMPONENT" above.
Characteristics: Plumbing fixture fitting components to be installed in accordance with the
manufacturer's instructions and the requirements of the latest edition of the
Uniform Plumbing Code.
Products listed on this certificate have been tested by an IAPMO R&T
recognized laboratory. This recognition has been granted based upon the
laboratory's compliance to the applicable requirements of ISO/IEC 17025.
Products are in compliance with the following standard(s):
-Rev. 1/22/2020- Void After: March 2024
Product: Plumbing Fixture Fittings - Components File No. MC-8435
Issued To: Hain Yo Enterprises Co., Ltd
ASME A112.18.1-2018/CSA B125.1-18
MODELS:
Ceramic Cartridge for Faucets:
25mm: GL02GJ, GH02GJ, GL12TD
35mm: FH02BD, FH02GJ, FL02BD, FL02GJ, FH12TD, FL19GJ, FH16GJ, FH17GJ, FL12TD
40mm: DH02BD, DH02GJ, DL02BD, DH17GJ, DH12TD DL02GJ, DH16GJ
Cartridge Valve for Bathtub Faucet:
45mm: MH04TD
Diverter for Bath/Shower Faucets:
33mm: KL18GJ
35mm: FL18GJ
Mixer+Diverter Cardridge for Bath/Shower Faucets:
40mm: DH19GJ, DL19GJ
Pressure Balance Valve for Bath/Shower/Tub Faucets:
40mm: JH01GJ(HK-40), JL01GJ(HJ-40), JH02BJ(HL-40), JL02BJ, JH02BD, JH04BD
EH12TD Single Handle Pressure Balancing Tub & Shower Set
JA01AJ Pressure Balancing Valve
JA03AJ Single Handle Pressure Balancing Tub & Shower Set
JL02BD Pressure Balancing Valve
JL04BD Pressure Balancing Valve
Page 3 of 3
This certificate is not evidence of current listing. To verify listing status,
visit the IAPMO R&T Product Listing Directory at pld.iapmo.org
-Rev. 1/22/2020- Void After: March 2024
Product: Plumbing Fixture Fittings - Components
Issued To: Hain Yo Enterprises Co., Ltd
File No. MC-8435
-
1
-
2
-
3
EVERSTEIN SF-3F10W-6603-BN User guide
- Type
- User guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI