Gorenje TGR100SMT User manual

TGR 30-120 SM

2

Instructions for Use 3

EN

Upute za upotrebu 11

Упaтства за употребa 19

Navodila za uporabo 28

Uputstva za upotrebu 36

HR BIH

SR

MK

SL

3

EN

WARNINGS

The appliance may be used by children older than 8 years

old, elderly persons and persons with physical, sensory or

mental disabilities or lacking experience and knowledge, if they

are under supervision or taught about safe use of the appliance

and if they are aware of the potential dangers.

Children should not play with the appliance.

Children should not clean or perform maintenance on the

appliance without supervision.

Installation should be carried out in accordance with the

valid regulations and according to the instructions of the

manufacturer and by qualified staff.

In a closed, pressurised system of installation, it is obligatory

to install a safety valve on the inlet pipe with a rated pressure of

0.6 MPa (6 bar), 0.9 MPa (9 bar) or 1.0 MPa (10 bar) (see the

label), which prevents the elevation of pressure in the boiler by

more than 0.1 MPa (1 bar) above the rated pressure.

Water may drip from the outlet opening of the safety valve,

so the outlet opening should be set to atmospheric pressure.

The outlet of the safety valve should be installed facing

downwards and in a non-freezing area.

To ensure proper functioning of the safety valve, the user

should perform regular controls to remove limescale and make

sure the safety valve is not blocked.

Do not install a stop valve between the water heater and the

safety valve, because it will impair the pressure protection of the

heater!

Before connecting it to the power supply, the water heater

must be filled with water!

The heater is equipped with an additional thermal cut-off for

protection in case of failure of the operating thermostat. In this

case, however, the temperature of the water in the heater can

reach up to 130 °C according to the safety standards. During

the water supply installation, the possibility of temperature

overloads should be taken into account.

If the heater is to be disconnected from the power supply,

please drain any water from the heater to prevent freezing.

4

EN

Please do not try to fix any defects of the water heater on

your own. Call the nearest authorised service provider.

Our products incorporate components that are both environmentally safe

and harmless to health, so they can be disassembled as easily as possible

and recycled once they reach their final life stage.

Recycling of materials reduces the quantity of waste and the need for

production of raw materials (e.g. metals) which requires a substantial

amount of energy and causes release of harmful substances. Recycling procedures

reduce the consumption of natural resources, as the waste parts made of plastic and

metal can be returned to various production processes.

For more information on waste disposal, please visit your waste collection centre or

the store where the product was purchased.

Dear buyer, thank you for purchasing our product.

Prior to the installation and first use of the electric water

heater, please read these instructions carefully.

In accordance with the latest guidelines, we have developed for our more demanding

customers the electric water heater TGR equipped with an intelligent electronic

regulator allowing the setting of the temperature of water in the heater as well as

smart "ECO

S

" mode of operation. The heater records your habits and after a while, it

calculates the optimal operating mode that enables minimal use of electric energy

necessary to meet your warm water needs.

This water heater has been manufactured in compliance with the relevant standards

and tested by the relevant authorities as indicated by the Safety Certificate and the

Electromagnetic Compatibility Certificate. The technical characteristics of the product

are listed on the label affixed between the inlet and outlet pipes. The installation must

be carried out by qualified staff. All repairs and maintenance work within the water

heater, e.g. lime removal or inspection/replacement of the protective anticorrosion

anode, must be carried out by an authorised maintenance service provider.

INSTALLATION

The water heater shall be installed as close as possible to the outlets. When installing

the water heater in a room with a bathtub or shower, take into account the

requirements defined in IEC Standard 60364-7-701 (VDE 0100, Part 701). It has to

be fitted to the wall using appropriate wall screws with a minimum diameter of 8 mm.

A wall with a poor load-bearing capacity must be properly reinforced where the heater

will be installed. The water heater may only be fixed upon the wall vertically. We

recommend the distance between the water heater and the ceiling is large enough to

allow simple replacement of the Mg anode (see dimension G in the Installation

Drawing), in order to avoid unnecessary dismounting of the heater during the

servicing intervention.

5

EN

Connection and installation dimensions

of the water heater [mm]

CONNECTION TO THE WATER SUPPLY

The water heater connections for the inlet and outlet of water are colour-coded. The

inlet of cold water is marked with blue colour, while the hot water outlet is marked

with red colour.

The water heater can be connected to the water supply in two ways. The closed-

circuit pressure system enables several points of use, while the open-circuit gravity

system enables a single point of use only. The mixer taps must also be installed in

accordance with the selected installation mode.

The open-circuit gravity system requires the installation of a non-return valve in order

to prevent the water from draining out of the tank in the event of the water supply

running dry or being shut down. This installation mode requires the use of a cross-

flow mixer tap. As the heating of water expands its volume, this causes the tap to

drip. The dripping cannot be stopped by tightening it further; on the contrary, the

tightening can only damage the tap.

The closed-circuit pressure system requires the use of pressure mixer taps. For

safety reasons the supply pipe must be fitted with a safety valve or alternatively, a

valve of the safety class that prevents the pressure in the tank from exceeding the

nominal pressure by more than 0.1 MPa (1 bar). The outlet opening on the relief

valve must be equipped with an outlet for atmospheric pressure.

The heating of water in the heater causes the pressure in the tank to increase to the

level set by the safety valve. As the water cannot return to the water supply system,

this can result in dripping from the outlet of the safety valve. The drip can be piped to

the drain by installing a catching unit just below the safety valve. The drain installed

below the safety valve outlet must be piped down vertically and placed in an

environment that is free from the onset of freezing conditions.

In case the existing plumbing does not enable you to pipe the dripping water from the

safety valve into the drain, you can avoid the dripping by installing a 3-litre expansion

tank on the inlet water pipe of the boiler.

In order to provide correct operation of the safety valve, periodical inspections of the

relief valve must be carried out by the user to eliminate any limescale and check if the

safety valve is blocked. To check the valve, open the outlet of the safety valve by

turning the handle or unscrewing the nut of the valve (depending on the type of the

valve). The valve is operating properly if the water comes out of the nozzle when the

outlet is open.

A B C G

TGR 30 SM 476 275 173 80

TGR 50 SM 578 365 185 130

TGR 80 SM 783 565 190 180

TGR 100 SM 943 715 200 260

TGR 120 SM 1098 865 205 260

6

EN

Closed (pressure) system Open (non-pressure) system

Between the water heater and safety valve, no closing valve may be built in

because it could impede the function of the safety valve.

The heater can be connected to the domestic water supply network without a

pressure-reducing valve if the pressure in the network is lower than the nominal

pressure. If the pressure in the network exceeds the nominal pressure, a pressure-

reducing valve must be installed.

Before connecting it to the power supply, the water heater must be filled with

water. When filling the heater for the first time, the tap for the hot water on the

mixing tap must be opened. When the heater is filled with water, the water starts to

run through the outlet pipe of the mixing tap.

CONNECTING THE WATER HEATER TO

THE POWER SUPPLY NETWORK

Before connecting to the power supply network, install a power supply cord in the

water heater, with a min. diameter of 1.5 mm

2

(H05VV-F 3G 1.5 mm

2

). To do this, the

protective plate must be removed from the water heater.

Connecting the heater to the power supply network must take place in

accordance with the standards for electric appliances. To comply with

the national installation regulations, an all poles disconnect switch

must be installed between the water heater and the power supply

network. When the heater is connected to the power supply, both

lights on the front panel will light up for 2 seconds.

Legend:

1 - Safety valve

2 - Test valve

3 - Non-return valve

4 - Pressure reduction valve

5 - Closing valve

6 - Checking fitting

7 - Funnel with outlet connection

8 - Expansion tank

H - Cold water

T - Hot water

7

EN

Legend:

1 - Connection terminal

2 - Electronic regulator and bipolar

thermal cut-out

3 - Electric heating element

L - Live conductor

N - Neutral conductor

- Earthing conductor

Electric installation

CAUTION: Before any intervention into the interior of the water heater,

disconnect it from the power supply network!

OPERATION AND MAINTENANCE

After connecting to the water and power supply, the heater is ready for use. The

heater is equipped with an electronic regulator that enables the setting of the

temperature of water, adjustment of the heater’s operation to your habits ("ECO

S

"

programme) and troubleshooting application.

OPERATION

The water heater is operated by turning the regulation knob to the desired level.

Switching on/off the heater

 To switch on the heater, turn the knob in the clockwise direction to reach the

desired temperature level.

 To switch off the heater, turn the knob to the "0" position (if the heater is

disconnected from the power supply, water must be drained from it in case of

danger of freezing).

8

EN

Temperature setting

 The desired temperature level is set by turning the knob in the clockwise direction.

ECO

S

- Temperature depends on the recorded needs of the user.

- Protection against freezing, temperature around 10 °C.

- Water temperature around 35 °C.

ECO - Water temperature around 55 °C.

- Water temperature around 75 °C.

The operation of the heater in the "ECO

S

" mode

This mode of operation is suitable if your hot water consumption habits are relatively

consistent (example: taking a shower at approximately the same time of the day).

Your habits are recorded and then taken into account when heating the water. The

operation of the heater in the "ECO

S

" mode reduces the consumption of electric

energy.

 The "ECO

S

" mode of operation can be switched on by twisting the control knob

counter clockwise. The green and red light start simultaneously. The red light

symbolises the functioning of the heater and the green light symbolises the "ECO

S

"

mode.

 The "ECO

S

" function is based on a 7-day cycle. During the first week of operation,

the water temperature in the heater is maintained at 75 °C and the programme

records the consumption pattern for seven consecutive days. After that, the

recorded pattern starts to be used automatically and the heater prepares the hot

water based on the measurements from the previous week. At the same time, the

heater continues to record the consumption. If the pattern differs from the previous

week in terms of time or volume, the newly recorded pattern is used the following

week.

 The water temperature in the "ECO

S

" mode is kept between 40 °C and 75 °C.

When no consumption is anticipated (standby temperature), the water is

maintained at 40 °C.

 If, during recording, there was a power failure or the heater was switched off, the

recording is not valid.

 The "ECO

S

" mode can be turned off by twisting the control knob to any other

position.

Anti-legionella function

The function is factory set. After connecting to the power supply or after eliminating

an error, the anti-legionella function is switched on after 3 days.

When the heater is switched on and the temperature of the water in the heater is

above 62 °C continuously for 15 minutes, the countdown is finished. As soon as the

temperature falls below 62 °C, a 30-day countdown begins again. If within 30 days

the heater does not reach 62 °C, the anti-legionella function is switched on and the

heater heats the water to the temperature of 62 °C for 15 minutes.

If the heater is not switched on or connected to the power supply and the 30-day

period expires, the anti-legionella function does not switch on until the heater is

turned on.

If the anti-legionella function is in operation and the user switches off the heater, the

function is interrupted and a new 30-day countdown begins.

9

EN

If the user lowers the set temperature during the operation of the anti-legionella

functions, the function is interrupted and a new 30-day countdown begins.

Error indication

In case of an error or warning on the heater, red and green light start blinking to

indicate an error according to the table below.

When the water heater is not in use for a longer period of time and is switched off or

disconnected from the power supply, it must be emptied in case of danger of

freezing. Water from the heater is drained through the inlet pipe of the heater. For this

purpose, a special fitting (T-fitting) must be mounted between the relief valve and the

heater inlet pipe, or a discharge tap. The heater can be discharged directly through

the relief valve, by rotating the handle or the rotating valve cap to the same position

as for checking the operation. Before discharge, make sure the heater is

disconnected from the power supply, and open the hot water on the connected mixer

tap. After discharging through the inlet pipe, there is still some water left in the water

heater. The remaining water will be discharged after removing the heating flange,

through the heating flange opening.

The external parts of the water heater can be cleaned with a mild detergent solution.

Do not use solvents and abrasives.

Regular preventive maintenance inspections ensure faultless performance and long

life of your heater. The first of these inspections should be carried out by the

authorised maintenance service provider about two years from installation in order to

inspect the wear of the protective anticorrosion anode and remove the lime coating

STATUS RED light GREEN light

Normal operation

Heater switched off / /

Heater switched on, no error, heater not

operating

/ /

Heater switched on, no error, heater

operating

GLOWING

/

Operation in ECO

S

mode

Heater switched on, no error, heater not

operating

/

GLOWING

Heater switched on, no error, heater

operating

GLOWING GLOWING

ERRORS (Call the service)

Heater switched on, temp. sensor error

(sensor 1 or sensor 2 in short circuit or open

circuit, temp. difference error)

BLINKING BLINKING

Heater switched on, heater warning

BLINKING BLINKING

10

EN

and sediment as required. The lime coating and sediment on the walls of the tank

and on the heating element is a result of quality, quantity and temperature of water

flowing through the water heater. The maintenance service provider shall also issue a

condition report and recommend the approximate date of the next inspection.

Never try to repair any possible faults of the water heater by yourself, but

inform about it the nearest authorised service workshop.

TECHNICAL PROPERTIES OF THE

APPLIANCE

1) EU Regulation 812/2013; EN 50440

2) EN 50440

3) Information on water heating energy efficiency and annual electricity consumption relate to enabled smart

control settings only.

WE RESERVE THE RIGHT TO MAKE CHANGES THAT DO NOT IMPAIR THE

FUNCTIONALITY OF THE DEVICE.

The user manual can also be found at our website http://www.gorenje.com .

Type

TGR 30 SM TGR 50 SM TGR 80 SM TGR 100 SM TGR 120 SM

Declared load profile S M M L L

Energy efficiency class

1)

C C C C C

Water heating energy efficiency

(ƞwh)

1)

[%] 34,5 37,3 37,2 38,0 37,6

Annual electricity consumption

1)

[kWh] 531 1378 1381 2691 2725

Daily electricity consumption

2)

[kWh] 2,715 6,985 7,251 13,502 13,843

Thermostat temperature settings "eco" "eco" "eco" "eco" "eco"

Value of "smart"

3)

1 1 1 1 1

Weekly electricity consumption with

smart control

[kWh] 14,801 26,658 30,211 55,225 55,725

Weekly electricity consumption

without smart control

[kWh] 15,998 29,071 34,121 59,985 61,057

Volume [l] 30,4 47,5 76,1 96,1 116,4

Quantity of mixed water at 40 °С

V40

2)

[l] - 67 116 134 168

Heating time from 10 °С to 65 °С [h] 0:59 1:38 2:37 3:16 3:55

Rated pressure [MPa (bar)] 0,6 (6)

Weight / Filled with water [kg] 20/50 24/74 30/110 34/134 38/158

Anti-corrosion of tank enamelled & Mg Anode

Power of electrical heater [W] 2000

Connection voltage [V~] 230

Protection class I

Degree of protection IP24

Page is loading ...

18

HR/BIH

Servisna služba preporuča datum naredne kontrole s obzirom na stanje grijalice.

POZOR! Eventualne kvarove grijalice nemojte popravljati sami već potražite

stručnu intervenciju najbliže ovlaštene servisne službe.

TEHNIČKA SVOJSTVA UREĐAJA

1) Uredba komisije EU 812/2013; EN 50440

2) EN 50440

3) Podatci o energijskoj učinkovitosti i potrošnji energije vrijede samo ako je uključen pametni upravljački

uređaj.

PRIDRŽAVAMO PRAVO NA IZMJENE KOJE NE UTJEČU NA FUNKCIONALNOST

UREĐAJA.

Upute za uporabu dostupne su i na našoj internetskoj stranici

http://www.gorenje.com .

Tip

TGR 30 SM TGR 50 SM TGR 80 SM TGR 100 SM TGR 120 SM

Deklarirani profil opterećenja S M M L L

Razred energetske učinkovitosti

1)

C C C C C

Energetska učinkovitost pri

zagrijavanju vode (ƞwh)

1)

[%] 34,5 37,3 37,2 38,0 37,6

Godišnja potrošnja električne

energije

1)

[kWh] 531 1378 1381 2691 2725

Dnevna potrošnja električne

energije

2)

[kWh] 2,715 6,985 7,251 13,502 13,843

Postavka temperature na termostatu "eco" "eco" "eco" "eco" "eco"

Vrijednost oznake "smart"

3)

1 1 1 1 1

Tjedna potrošnja električne energije s

pametnim upravljanjem

[kWh] 14,801 26,658 30,211 55,225 55,725

Tjedna potrošnja električne energije

bez pametnog upravljanja

[kWh] 15,998 29,071 34,121 59,985 61,057

Korisna zapremnina [l] 30,4 47,5 76,1 96,1 116,4

Količina miješane vode pri 40 °С

V40

2)

[l] - 67 116 134 168

Vrijeme zagrijavanja od 10 °С

do 65 °С

[h] 0:59 1:38 2:37 3:16 3:55

Nazivni tlak [MPa (bar)] 0,6 (6)

Masa grijalice/napunjene vodom [kg] 20/50 24/74 30/110 34/134 38/158

Zaštita kotla od korozije Emajlirano / Mg anoda

Snaga električnoga grijača [W] 2000

Priključni napon [V~] 230

Klasa zaštite I

Stupanj zaštite IP24

Page is loading ...

35

SL

TEHNIČNE LASTNOSTI APARATA

1) Uredba komisije EU 812/2013; EN 50440

2) EN 50440

3) Podatki o energijski učinkovitosti in porabi energije veljajo samo ob vključeni pametni krmilni napravi.

PRIDRŽUJEMO SI PRAVICO DO SPREMEMB, KI NE VPLIVAJO NA

FUNKCIONALNOST APARATA.

Navodila za uporabo so na voljo tudi na naših spletnih straneh

http://www.gorenje.com .

Tip

TGR 30

SM

TGR 50

SM

TGR 80

SM

TGR 100

SM

TGR 120

SM

Določeni profil obremenitve S M M L L

Razred energijske učinkovitosti

1)

C C C C C

Energijska učinkovitost pri ogrevanju

vode (ƞwh)

1)

[%] 34,5 37,3 37,2 38,0 37,6

Letna poraba električne energije

1)

[kWh] 531 1378 1381 2691 2725

Dnevna poraba električne energije

2)

[kWh] 2,715 6,985 7,251 13,502 13,843

Nastavitev temperature termostata "eco" "eco" "eco" "eco" "eco"

Vrednost "smart"

3)

1 1 1 1 1

Tedenska poraba električne energije

s pametnim upravljanjem

[kWh] 14,801 26,658 30,211 55,225 55,725

Tedenska poraba električne energije

brez pametnega upravljanja

[kWh] 15,998 29,071 34,121 59,985 61,057

Prostornina [l] 30,4 47,5 76,1 96,1 116,4

Količina mešane vode pri 40 °С

V40

2)

[l] - 67 116 134 168

Čas segrevanja od 10 °С do 65 °С [h] 0:59 1:38 2:37 3:16 3:55

Nazivni tlak [MPa (bar)] 0,6 (6)

Masa / napolnjen z vodo [kg] 20/50 24/74 30/110 34/134 38/158

Protikorozijska zaščita kotla Emajlirano / Mg anoda

Priključna moč [W] 2000

Napetost [V~] 230

Razred zaščite I

Stopnja zaščite IP24

Page is loading ...

43

SR/MNE

TEHNIČKE KARAKTERISTIKE

BOJLERA

1) Uredba komisije EU 812/2013; EN 50440

2) EN 50440

3) Podaci o energetskoj efikasnosti i potrošnji energije važe samo kada je uključen pametni upravljački uređaj.

ZADRŽAVAMO PRAVO NA PROMENE, KOJE NE UTIČU NA FUNKCIONALNOST

APARATA.

Uputstvo za upotrebu je na raspolaganju i na našoj internet strani

http://www.gorenje.com .

Tip

TGR 30

SM

TGR 50

SM

TGR 80

SM

TGR 100

SM

TGR 120

SM

Određeni profil opterećenja S M M L L

Razred energetske efikasnosti

1)

C C C C C

Energetsta efikasnost pri zagrevanju

vode (ƞwh)

1)

[%] 34,5 37,3 37,2 38,0 37,6

Godišnja potrošnja električne energije

1)

[kWh] 531 1378 1381 2691 2725

Dnevna potrošnja električne energije

2)

[kWh] 2,715 6,985 7,251 13,502 13,843

Podešavanje temperature termostata "eco" "eco" "eco" "eco" "eco"

Vrednost "smart"

3)

1 1 1 1 1

Nedeljna potrošnja električne energije

sa pametnim upravljanjem

[kWh] 14,801 26,658 30,211 55,225 55,725

Nedeljna potrošnja električne energije

bez pametnog upravljanja

[kWh] 15,998 29,071 34,121 59,985 61,057

Zapremina [l] 30,4 47,5 76,1 96,1 116,4

Količina mešane vode na 40 °С V40

2)

[l] - 67 116 134 168

Vreme zagrevanja od 10 °С do 65 °С [h] 0:59 1:38 2:37 3:16 3:55

Nominalni pritisak [MPa (bar)] 0,6 (6)

Masa/napunjen vodom [kg] 20/50 24/74 30/110 34/134 38/158

Antikorozivna zaštita kotla emajlirano / Mg anoda

Snaga električnog grejača [W] 2000

Napon napajanja [V~] 230

Klasa zaštite I

Stepen zaštite IP24

10/2016

390735

Gorenje TGR100SMT User manual

This manual is also suitable for

Gorenje TGR100SMT User manual

Related papers

Other documents