Fire Magic Echelon Firebox Liner Kit User manual

Category
Barbecues & grills
Type
User manual
REV 0 - 1512070750
L-C2-476
1
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
Liner left
4
This fi rebox liner kit is for installation on Echelon grills. Installation on an E1060 is depicted in this instruction.
READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
Tools required: Gloves, Phillips screwdriver, power drill,
3
/32" drill bit, rubber mallet, pliers, needle-nose pliers,
hammer, and a
1
/4" nut driver (or equivalent).
Be sure the grill is completely cool and the gas is completely shut off.
IMPORTANT: CLEAN THE INTERIOR OF THE GRILL OF ALL DEPOSITS AND GREASE PRIOR TO
INSTALLING THE FIREBOX LINER KIT.
Note: Wear gloves whenever installing and handling this liner kit as some components have sharp edges.
As applicable, remove the warming rack, cooking grids, fl avor grids, zone separators, burners, burner
igniters, infrared burners, infrared burner igniters, air baffl es, and fl ash tubes. Open the control panel. If
the smoker drawer assembly is not welded down, remove it as well. Reference your owner's manual for
removal details if needed.
Note: The fl avor grids, air baffl es, and fl ash tubes that are being removed from your grill are no longer
needed and may be discarded. The items included in this kit will replace these parts.
Table 1
Liner back
2
Liner center
1
Liner Front
3
Liner right
5
Drive screw
Firebox Liner Kit
Model # 24183-RLK
24188-RLK
24193-RLK
Model Part No.
Parts List
Firebox
liner
pieces
Smoker
drawer
cover
Air
baffl e
Flash
tube
Flash
tube
plate
Drive
screw
Self-tapping
hex screw
Flavor
grid *
Drill
bit
(2mm)*
E1060
24183-RLK
51344121642
E790
24188-RLK
51133121432
E660
24193-RLK
51133121432
E1060 kit shown
ECHELON
Self-tapping
hex screw
7
6
Smoker
drawer
cover
Flash
tube
8
9
7
7
(1060 models)
(790 models)
(660 models)
Air baffl es
*
Not shown
† Includes 4 extra
drive screws
LINER
CENTER
1
LINER
BACK
2
LINER
LEFT
4
SMOKER D
RW
COVER
6
AIR
BAFFLE
7
AIR
BAFFLE
9
AIR
BAFFLE
8
AIR
BAFFLE
7
AIR
BAFFLE
7
Flash tube
plate
I
REV 0 - 1512070750
L-C2-476
2
Procedure continued on next page
Place the rear liner (item 2) ensuring it rests fl at against
grill rear fi rebox wall. The two tabs (on center liner) must
extend up through the slots in the rear liner.
Note: If needed, use a rubber mallet to assist in
proper placement of liner panels.
Place the center liner (item 1 of parts list) into the grill
drainage channel (A). The liner will need to be bent in order
to slide it under the smoker drawer (B). Ensure the liner
rests fl at in place (C).
Note: It is recommended to slightly bend the 4 tabs
inward to assist in front and rear liner installation.
Note: If smoker drawer assembly was removed, re-install
it at this time.
II
Install
center
liner
Install rear liner
LINER
CENTER
1
A
C
Bend liner from crease
for ease of installation
(if needed)
B
LINER
CENTER
1
LINER
BACK
2
Tabs must clear
the openings
Place the front liner (item 3) ensuring it rests fl at against
the grill front fi rebox wall, and the two tabs (on center liner)
extend up through the slots in the front liner.
Note: If needed, the thermocouples may be removed for
ease of the front liner installation.
Install front
liner
LINER
CENTER
1
LINER
FRONT
3
Tabs must clear
the openings
LINER
BACK
2
Place the left liner (item 4) as shown above. Rest the liner
OVER the front and rear liner fl anges (hiding the fl anges)
and ensure the 4 holes are aligned with the 4 grill wall rivets.
To secure the liner, align each drive screw (included in kit)
with the corresponding hole and carefully hammer each
drive screw into the panel. Use needle-nose pliers to assist
in holding the drive screws properly.
Note: The drive screw will force out the center of
the existing rivet. Therefore, ensure to use
ample force when driving the screw through
the retaining rivet.
REPEAT THIS STEP FOR THE RIGHT LINER (item 5).
IV
Place left liner
LINER
LEFT
4
III
V
The drive screws
must be aligned
when hammering
New left
liner
New liner
ange
Existing
rebox
CORRECT
INCORRECT
New
liner
ange
Existing
rebox
ng
ti
New left
liner
REV 0 - 1512070750
L-C2-476
3
Pre-drill pilot holes through the original grill liner using the
supplied drill bits. Place the smoker drawer cover (item 6)
ensuring it rests fl at on the original smoker drawer. Fasten
using the provided self-tapping hex screws and a
1
/4" nut
driver or equivalent.
Install the provided fl ash tube and fl ash tube plate by
aligning the plate (A) and fl ash tube (B) to the original liner
mounting holes. Using a
1
/4" nut driver or equivalent, affi x
with the supplied hex screws. Repeat this procedure for
the other fl ash tubes.
VI
Install the air baffl es according to your model above. To properly install, the tabs must slide into the slots located on the liners.
Using pliers, bend in the four tabs inward toward the middle
of the center liner to lock the liner panels together.
Flash tube
plate
Install smoker
drawer cover
E1060 Models E790 Models E660 Models
VIII
Install the burners, burner igniters, infrared burners (if applicable), infrared burner igniters (if applicable), thermocouples
(if removed), zone separators, new fl avor grids, the control panel, cooking grids, and warming rack. Reference your
owner's manual for installation details if needed.
IX
LINER
CENTER
1
LINER
FRONT
3
LINER
BACK
2
Bend
tabs inward
LINER
CENTER
1
LINER
FRONT
3
LINER
BACK
2
SMOKER DRW
COVER
6
LINER
RIGHT
5
SMOKER DRW
COVER
6
SMOKER DRW
COVER
6
SMOKER DRW
COVER
6
AIR
BAFFLE
7
AIR
BAFFLE
7
AIR
BAFFLE
8
AIR
BAFFLE
9
AIR
BAFFLE
7
Item 9
Item 7
Item 8
Item 7
Item 7
A
B
Flash tube
x 2
(per fl ash tube)
x 8
VII
X
REV 0 - 1512070750
L-C2-476
4
NOTES PAGE
Please use this page to record any information about your unit that you may want to have at hand.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Fire Magic Echelon Firebox Liner Kit User manual

Category
Barbecues & grills
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI