ShelterLogic 70435 Owner's manual

Brand
ShelterLogic
Model
70435
Type
Owner's manual
05_70435_70437_0BPage 1
Shed-in-a-Box RoundTop
®
10' x 10' x 8'
Assembly Instructions
DESCRIPTION MODEL #
Shed-in-a-Box RoundTop
®
- Grey
70435
Shed-in-a-Box RoundTop
®
- Sandstone
70437
Before you start: 2 or more individuals recommended for assembly, approximate time 1
1
/
2
hours.
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE.
1-800-524-9970
1-800-559-6175
Canada:
RECOMMENDED TOOLS
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
OR
1/24/12
05_70435_70437_0BPage 2
Risk of re. DO NOT smoke or use open ame devices (including grills, re pits, deep fryers, smokers or
lanterns) in or around the shelter. DO NOT store ammable liquids (gasoline, kerosene, propane, etc.) in
or around your shelter. Do not expose top or sides of the shelter to open re or other ame source.
WARNING:
PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
ShelterLogic
®
Corp.
is not responsible for damage to the unit or the contents from acts of nature. Any shelter that is not anchored
securely has the potential to y away causing damage, and is not covered under the warranty. Periodically check the anchors to ensure
stability of shelter. ShelterLogic
®
Corp. cannot be responsible for any shelter that blows away. NOTE: Your shelter’s cover can be
quickly removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we
recommend removal of cover.
PROPER ANCHORING AND INSTALLATION OF FRAME:
Covered by U.S. Patents and patents pending: 6,871,614; 6,994,099; 7,296,584; D 430,306; D 415,571; D 414,564; D 409,310; D 415,572
A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate
deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a
broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always
remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to
remove snow. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to
clean the fabric cover. Cover is easily cleaned with mild soap and water.
CARE AND CLEANING:
ATTENTION:
This shelter product is manufactured with quality materials. It is designed to t the ShelterLogic
®
Corp. custom fabric cover included.
ShelterLogic
®
Corp. Shelters offer storage and protection from damage caused by sun, light rain, tree sap, animal - bird excrement
and light snow. Please anchor this ShelterLogic
®
Corp. structure properly. See manual for more anchoring details. Proper anchoring,
keeping cover tight and free of snow and debris is the responsibility of the consumer. Please read and understand the installation detail,
warnings and cautions prior to beginning installation. If you have any questions call the customer service number listed below. Please
refer to the warranty card inside this package.
Prior to installation, consult with all local municipal codes regarding installation of temporary shelters.
Choose the location of your shelter carefully. DANGER: Keep away from electrical wires. Check for
overhead utility lines, tree branches or other structures. Check for underground pipes or wires before
you dig. DO NOT install near roof lines or other structures that could shed snow, ice or excessive run
off onto your shelter. DO NOT hang objects from the roof or support cables.
DANGER:
CAUTION:
Use CAUTION when erecting the frame. Use safety goggles during installation. Secure and bolt together
overhead poles during assembly. Beware of pole ends.
REPLACEMENT PARTS, ASSEMBLY, SPECIAL ORDERS:
Genuine ShelterLogic
®
Corp. replacement parts and accessories are available from the factory, including anchoring kits for nearly any
application, replacement covers, wall and enclosure kits, vent and light kits, frame parts, zippered doors and other accessories. All
items are shipped factory direct to your door.
This shelter carries a full limited warranty against defects in workmanship. ShelterLogic
®
Corp. warrants to the Original Purchaser that
if properly used and installed, the product and all associated parts, are free from manufacturer’s defects for a period of:
1 YEAR FOR COVER FABRIC, END PANELS AND FRAMEWORK.
Warranty period is determined by date of shipment from ShelterLogic
®
Corp. for factory direct purchases or date of purchase from an authorized
reseller, (please save a copy of your purchase receipt). If this product or any associated parts are found to be defective or missing at the time of receipt,
ShelterLogic
®
Corp. will repair or replace, at it’s option, the defective parts at no charge to the original purchaser. Replacement parts or repaired
parts shall be covered for the remainder of the Original Limited Warranty Period. All shipping costs will be the responsibility of the customer. Parts and
replacements will be sent C.O.D. You must save the original packaging materials for shipment back. If you purchased from a local dealer, all claims
must have a copy of original receipt. After purchase, please ll out and return warranty card for product registration. Please see warranty card for more
details.
WARRANTY:
QUESTIONS - CLAIMS - SPECIAL ORDERS? CALL OUR CUSTOMER SERVICE HOTLINE:
U.S. CUSTOMER SERVICE: 1-800-524-9970 INTERNATIONAL CUSTOMER SERVICE: 001-860-945-6442 CANADA CUSTOMER SERVICE: 1-800-559-6175
HOURS OF OPERATION: MON-FRI 8:30AM-8:00PM EST, SAT-SUN 8:30AM-5:00PM EST.
090111
05_70435_70437_0BPage 3
Shed-in-a-Box RoundTop
®
10' x 10' x 8' - Parts List - Model 70435 or 70437
Quantity Part #
Description of Parts:
Bolts
1
/
4
x 1
7
/
8
in.
/
6,4 x 47,6 mm
18
Half-Clamps for Middle Legs
ShelterLock II
®
Stabilizer
Ratchet Clamp
Half-Clamps for Corner Legs
Bolts
1
/
4
x 1
5
/
8
in.
/
6,4 x 41,3 mm
Nut
1
/
4
in.
/
6,4 mm
Base Feet
4
4
4
15 in. Auger Anchors (Temporary)
Cable Clamps
Cable - 1 ft. Length
Rib Peak 40
3
/
4
in.
/
103,6 cm
Rafter Bend 48
in.
/
121,8 cm
Leg Pipe 41
in.
/
104,1 cm
Middle Leg Pipe 24
3
/
4
in.
/
62,8 cm
Corner Leg Bend 33
3
/
4
in.
/
86,1 cm
3
6
6
4
9
3
4
9
8
46
28
2
2
8
8
2
1
1
1
1
1
1
4
4
Cover Rails 36
1
/
4
in.
/
92,4 cm
Cover Rails, Swedge 24
1
/
4
in.
/
61,5 cm
Cross Rails, Swedge 31
3
/
4
in.
/
80,5 cm
Cross Rails 30
1
/
2
in.
/
77,8 cm
Washer
1
/
4
in.
/
6,4 mm
White Bungee Cords (For holding door open)
03032
13201
13202
800939
10115
01010
12270
801034
801033
800921
800923
800922
800163
800599
800598
13345
01011
10066
800947
801360
801359
801358
800948
800949
10240
10014
10016
10015
00847
}
Cover - Gray (Model # 70435)
Cover - Sandstone (Model # 70437)
Back Panel - Gray (Model # 70435)
Back Panel - Sandstone (Model # 70437)
2-Zipper Door - Gray (Model # 70435)
2-Zipper Door - Sandstone (Model # 70437)
05_70435_70437_0BPage 4
801033
800921
800939
03032
01010
1. ASSEMBLE END RIBS
2. ASSEMBLE MIDDLE RIB
800922
800923
800923
12270
12270
800921
800921
801033
801034
801033
800939
800939
800939
800939
800921
800921
800922
ShelterLock II
®
Connection
Secure connections using Bolts as shown with #01010 Nuts.
801034
801033801033
#10115 Bolts (1
5
/
8
")
#10115 Bolts (1
5
/
8
")
#03032 Bolts (1
7
/
8
")
#03032 Bolts (1
7
/
8
")
#10115 Bolts (1
5
/
8
")
#10115 Bolts (1
5
/
8
")
NOTE:
The bolt heads at
the end ribs must be facing
outward to avoid damaging
your cover.
05_70435_70437_0BPage 5
Cross Rails
A. Assemble 2 Cover Rails using parts as shown.
B. Assemble 3 Cross Rails using parts as shown.
C. Connect the Cross Rails to the End Rib at the ShelterLocks.
D. Place a Cover Rail at each leg and secure it with a Cover Clamp as shown. Slide the Cover Rails so they
are 8 inches up from the ground. Only HAND-TIGHTEN these bolts!
ShelterLock II
®
connections use #03032 (1
7
/
8
") Bolts. Cover Rail Clamp connections use #10115 (1
5
/
8
") Bolts.
3. ATTACH CROSS RAILS AND COVER RAILS TO FRONT END RIB
4. CONNECT MIDDLE RIB TO FRONT END RIB
800939
800939
800939
800939
13201
13201
Assemble Cover Rails
ShelterLock II
®
connections use #03032 (1
7
/
8
") Bolts. Cover Rail Clamp connections use #10115 (1
5
/
8
") Bolts.
Cross Rails face toward the inside of the shed.
Cover Rails
NOTE:
The bolt heads at
the end ribs must be facing
outward to avoid damaging
your cover.
ShelterLock II
®
End Rib Connection
13345 800163
No Bolt at this connection
A
Assemble Cross Rails
800599 800599
10115
01010
B
C
800939
03032
01010
Cross Rail
D
10115
Cover
Rail
13202
End Rib
01011
01010
End Rib Cover Rail Clamps
10115
Cover Rail
13201
Middle
Rib
01010
01011
Middle Rib Cover Rail Clamps
NOTE:
All detail views
are from the inside.
05_70435_70437_0BPage 6
10115
Cover
Rail
Cover
Rail
13201
Middle
Rib
01010
01011
01010
01011
D
800598
5. CONNECT REAR END RIB
A. Repeat Cover Rail assembly steps.
B. Assemble Cross Rails using parts as shown.
C. Repeat steps to connect Cross Rails with ShelterLocks.
D. Repeat steps to connect Cover Rails with Cover Rail Clamps. Only HAND-TIGHTEN these bolts!
ShelterLock II
®
connections use #03032 (1
7
/
8
") Bolts. Cover Rail Clamp connections use #10115 (1
5
/
8
") Bolts.
Cross Rails face toward the inside of the shed.
Assemble Cross Rails
800599 800598
10115
01010
B
Assemble Cover Rails
13345 800163
No Bolt at this connection
A
D
10115
Cover
Rail
13202
End Rib
01011
01010
800939
03032
01010
Middle
Rib
Cross Rail
ShelterLock II
®
Middle Rib Connection
C
End Rib Cover Rail Clamps
NOTE:
The bolt heads at
the end ribs must be facing
outward to avoid damaging
your cover.
Middle Rib Cover Rail Clamps
NOTE:
All detail views
are from the inside.
05_70435_70437_0BPage 7
10 ft.
10 ft.
6. SQUARING UP THE FRAME
A. Place frame in its nal location, which needs to be as at and level as possible.
B. Check that the front and rear of the frame measures 10 feet in width.
C. Measure across opposite corners. These distances must be equal to within 1 inch.
7. PROPERLY ANCHOR FRAME
Your unit comes with 4 temporary Shelter Auger
™
Earth Anchors. For best results, ShelterLogic
recommends additional anchors, one for each foot of your frame.
A. Anchors must be placed inside shelter at the corners of the shelter. Insert a ¾-inch pipe or steel rod,
through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the
ground by 1 to 2 inches so it can be anchored to the legs.
If ground is too hard, dig a hole with a shovel or post hole tool. Optional: Place auger in hole and ll with cement.
B. Thread cable provided through the eyelets of the Anchor as indicated in gure. Secure the cable with the
clamps provided.
WARNING:
Serious injury to persons or
property could result if cover
is installed and shelter is
not anchored and is left
unattended. Shelter must be
securely anchored before
use.
NOTE:
15" Augers are for temporary use only!
For best results ShelterLogic recommends
using our Easy Hooks
™
(#10036 4-pack, #10035
6-pack, or #10038 8-pack) for a stronger, more
secure installation.
Call 1-800-524-9970
or visit
www.shelterlogic.com for
more information.
End Rib Anchors
05_70435_70437_0BPage 8
8. DOOR PANEL AND BACK PANEL INSTALLATION
A. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. (2) Wrap the edges
of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric.
A1 A2
C. (1) Disconnect side cross rail from the end rib.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the side cross rail to the end rib.
C2 C3
B. (1) Disconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib.
Leave the ShelterLock II
®
attached to the rib with the bolt.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the top cross rail to the end rib.
C1
B2 B3B1
05_70435_70437_0BPage 9
PULLPULL
WEBBING
STRAP
END PANEL VIEW
FROM INSIDE
SHED
D. At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a
drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket.
E. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is
centered on the building before fully tightening the end panel.
F. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOTE: Keep zippers
closed when tightening door panel.
D
E F
8. END PANEL INSTALLATION - continued
Insert Webbing into
Ratchet
05_70435_70437_0BPage 10
10115
Cover
Rail
13202
End Rib
01011
01010
9. INSTALLING COVER WITH COVER RAILS
A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing
down and the webbing on the front and rear of the corner of the building. Pull cover over the frame.
B. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself.
C. Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg.
Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely.
D. Check and tighten Ratchets and Cross Rails monthly to ensure the cover is tight.
NOTE: The ShelterLogic
®
logo should
be oriented as shown below.
CORRECT
COVER RAILS
Webbing and Ratchets Securing Cover
INCORRECT
End Rib Cover Rail Clamps
10115
13201
Middle
Rib
01010
01011
Middle Rib Cover Rail Clamps
01010
01011
Cover
Rail
Cover
Rail
NOTE:
All detail views
are from the inside.
Page 11 05_70435_70437_0B
Shed-in-a-Box RoundTop
®
10 x 10 x 8 pi (3 x 3 x 2,4 m)
Guide D’assemblage
DÉSIGNATION MODÈLE N°
Shed-in-a-Box RoundTop
®
- Gris
70435
Shed-in-a-Box RoundTop
®
- Grès
70437
1-800-524-9970
1-800-559-6175
Canada:
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
Avant de commencer : Il est recommandé que l’assemblage soit réalisé par au moins 2 personnes, ce qui
devrait prendre environ 1
1
/
2
heures.
Veuillez lire les instructions EN ENTIER avant d’entreprendre l’assemblage. Cet abri DOIT
être ancré solidement.
CETTE STRUCTURE TEMPORAIRE EST DÉCONSEILLÉE POUR UN USAGE PERMANENT.
OUTILS RECOMMANDÉS
OU
1/23/12
Page is loading ...
Page 13 05_70435_70437_0B
Shed-in-a-Box RoundTop
®
10 x 10 x 8 pi (3 x 3 x 2,4 m) - Liste des Pièces – Modèle 70435 ou 70437
18
4
4
4
Nervure Supérieure 40
3
/
4
in.
/
103,6 cm
Arc de Chevron 48
in.
/
121,8 cm
Tuyau de Pied 41
in.
/
104,1 cm
Tuyau de Montant Central 24
3
/
4
in.
/
62,8 cm
Arc de Montant de Coin 33
3
/
4
in.
/
86,1 cm
3
6
6
4
9
3
4
9
8
46
28
2
2
8
8
2
4
4
Rail de Toile 36
1
/
4
in.
/
92,4 cm
Rail de Toile, Swedge 24
1
/
4
in.
/
61,5 cm
Traverse, Swedge 31
3
/
4
in.
/
80,5 cm
Traverse 30
1
/
2
in.
/
77,8 cm
03032
13201
13202
800939
10115
01010
12270
801034
801033
800921
800923
800922
800163
800599
800598
13345
01011
10066
10240
10014
10016
10015
00847
}
Quantité N° de Pièce
Description des pièces
Boulon
1
/
4
x 1
7
/
8
po
/
6,4 x 47,6 mm
Demi-bride pour Montant Central
Stabilisateur ShelterLock II
®
Bride à Cliquet
Demi-bride pour Montant de Coin
Boulon
1
/
4
x 1
5
/
8
po
/
6,4 x 41,3 mm
Écrou
1
/
4
po
/
6,4 mm
Pied
Rondelle
1
/
4
po
/
6,4 mm
Cordon Élastique Blanc
(pour garder la porte ouverte)
Ancrage à Tarière (temporaire), 15 po
Bride de Câble
Câble, 1 pi de Longueur
1
1
1
1
1
1
800947
800948
800949
Toile - Gris (Model # 70435)
Toile - Grès (Model # 70437)
Panneau Arrière - Gris (Model # 70435)
Panneau Arrière - Grès (Model # 70437)
Porte à 2 Glissières - Gris (Model # 70435)
Porte à 2 Glissières - Grès (Model # 70437)
801360
801359
801358
Page 14 05_70435_70437_0B
801033
800921
800939
03032
01010
800922
800923
800923
12270
12270
800921
800921
801033
801034
801033
800939
800939
800939
800939
800921
800921
800922
801034
801033801033
1. ASSEMBLEZ LES NERVURES D’EXTRÉMITÉ
2. ASSEMBLEZ LES NERVURES CENTRALES
Raccord ShelterLock II
®
Fixez les raccords avec les boulons indiqués et les écrous (n° 01010).
REMARQUE :
La tête
des boulons aux nervures
d’extrémité doit être orientée
vers l’extérieur pour éviter
d’endommager la toile.
Boulons n° 03032
(1
7
/
8
po)
Boulons n° 10115 (1
5
/
8
po)
Boulons n° 10115 (1
5
/
8
po)
Boulons n° 03032
(1
7
/
8
po)
Boulons n° 10115 (1
5
/
8
po)
Boulons n° 10115 (1
5
/
8
po)
Page 15 05_70435_70437_0B
4. FIXEZ LA NERVURE CENTRALE À LA NERVURE AVANT
800939
800939
800939
13201
13201
Pour xer les raccords ShelterLock II
®
, utilisez les boulons n° 03032 (1
7
/
8
po) et n° 10115 (1
5
/
8
po).
Répétez les étapes d’assemblage des rails de toile.
Traverse
800939
Rail de Toile
C
800939
03032
01010
Traverse
D
10115
Rail de
Toile
13202
Nervure
d’extrémité
01011
01010
REMARQUE :
La tête
des boulons aux nervures
d’extrémité doit être orientée
vers l’extérieur pour éviter
d’endommager la toile.
Raccords de rail de toile pour
nervure d’extrémité
Raccord ShelterLock II
®
pour
nervure d’extrémité
10115
Rail de
Toile
13201
Nervure
Centrale
01010
01011
Raccords de Rail de Toile pour Nervure Centrale
A. Assemblez deux rails de toile comme le montre l’illustration.
B. Assemblez trois traverses comme le montre l’illustration.
C. Reliez les traverses à la nervure d’extrémité avec les raccords ShelterLock.
D. Placez un rail de toile à chaque pied et xez-le avec une pince de toile comme le montre l’illustration. Faites
glisser les rails de toile jusqu’à ce qu’ils se trouvent à 8 pouces du sol. Serrez ces boulons À LA MAIN
seulement!
Pour xer les raccords ShelterLock II
®
, utilisez les boulons n° 03032 (1
7
/
8
po) et n° 10115 (1
5
/
8
po).
3. FIXEZ LES TRAVERSES ET LES RAILS DE TOILE À LA NERVURE
D’EXTRÉMITÉ AVANT
Assemblez les rails de toile
13345 800163
Aucun boulon à ce raccord
A
Assemblez les traverses
800599 800599
10115
01010
B
REMARQUE:
Toutes
les vues de détail sont
de l'intérieur.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
05_70435_70437_0BPágina 21
1-800-524-9970
1-800-559-6175
Canada:
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
Shed-in-a-Box RoundTop
®
de 10 x 10 x 8 pi (3,05 m x 3,05 m x 2,4 m)
Instrucciones de Ensamble
DESCRIPCIÓN MODELO #
Shed-in-a-Box RoundTop
®
- Gris
70435
Shed-in-a-Box RoundTop
®
- Arenisca
70437
1/24/12
Antes de empezar Se recomiendan 2 personas o más para ensamblar, tempo aproximado 1
1
/
2
horas.
Por favor lea COMPLETAMENTE antes de ensamblar. Este toldo DEBE de ser anclado de manera Segura.
ESTA ES UNA ESTRUCTURA TEMPORAL Y NO SE RECOMIENDA COMO ESTRUCTURA PERMANENTE.
HERRAMIENTAS RECOMENDADAS
O
Page is loading ...
05_70435_70437_0BPágina 23
18
4
4
4
3
6
6
4
9
3
4
9
8
46
28
2
2
8
8
2
4
4
03032
13201
13202
800939
10115
01010
12270
801034
801033
800921
800923
800922
800163
800599
800598
13345
01011
10066
10240
10014
10016
10015
00847
}
Shed-in-a-Box RoundTop
®
de 10 x 10 x 8 pi (3,05 m x 3,05 m x 2,4 m) Lista de Partes - Modelo 70435 o 70437
Cantidad Parte #
Descripción de Partes:
Tornillos
1
/
4
x 1
7
/
8
pu.
/
6,4 x 47,6 mm
Abrazaderas para las patas intermedias
Estabilizador ShelterLock II
®
Trinquete
Abrazaderas para las patas de esquina
Tornillos
1
/
4
x 1
5
/
8
pu.
/
6,4 x 41,3 mm
Tuerca
1
/
4
pu.
/
6,4 mm
Patas de Base
Anclas 15 pu.
/
38,1 cm (Temporales)
Abrazaderas de Cable
Cable - 1 pi.
/
30,5 cm de Largo
Soporte Curvo 40
3
/
4
pu.
/
103,6 cm
Soporte Travesaño 48
pu.
/
121,8 cm
Tubo de Pata 41
pu.
/
104,1 cm
Tubo de Pata Intermedia 24
3
/
4
pu.
/
62,8 cm
Pata de Esquina Doblada 33
3
/
4
pu.
/
86,1 cm
Rieles de Cubierta 36
1
/
4
pu.
/
92,4 cm
Rieles de Cubierta, Swedge 24
1
/
4
pu.
/
61,5 cm
Rieles de Cruce, Swedge 31
3
/
4
pu.
/
80,5 cm
Rieles de Cruce 30
1
/
2
pu.
/
77,8 cm
Arandela
1
/
4
pu.
/
6,4 mm
Cuerdas Bungee Blancas
(para sujetar abierta la puerta)
1
1
1
1
1
1
800947
800948
800949
Cubierta - Gris (Model # 70435)
Cubierta - Arenisca (Model # 70437)
Panel Posterior - Gris (Model # 70435)
Panel Posterior - Arenisca (Model # 70437)
Puerta de 2 Cremalleras Cierre - Gris (Model # 70435)
Puerta de 2 Cremalleras Cierre - Arenisca (Model # 70437)
801360
801359
801358
05_70435_70437_0BPágina 24
801033
800921
800939
03032
01010
1. ENSAMBLE LOS SOPORTE CURVOS DE EXTREMO
2. ENSAMBLE LOS SOPORTES CURVOS INTERMEDIOS
800922
800923
800923
12270
12270
800921
800921
801033
801034
801033
800939
800939
800939
800939
800921
800921
800922
Conexión ShelterLock II
®
Asegure las conexiones usando tornillos como se muestran con tuercas #01010.
801034
801033801033
#10115 Tornillos
(1
5
/
8
pu. / 4,13 cm)
#10115 Tornillos
(1
5
/
8
pu. / 4,13 cm)
#10115 Tornillos
(1
5
/
8
pu. / 4,13 cm)
#10115 Tornillos
(1
5
/
8
pu. / 4,13 cm)
#03032 Tornillos
(1
7
/
8
pu. / 4,76 cm)
#03032 Tornillos
(1
7
/
8
pu. / 4,76 cm)
Las cabezas
de perno en los soportes
curvos de extremo deben
de dar hacia afuera para
evitar daños a la cubierta.
NOTA:
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
05_70435_70437_0BPágina 30
A. Coloque la tapa en el suelo junto a la estructura con el interior de la cubierta (el lado con los bolsillos de
tubo) hacia abajo y la correa en la parte delantera y trasera de la esquina de la estructura. Estire la cubierta
sobre el marco.
B. Inserte el gancho "S" – en el trinquete en el agujero en la pata curva. Inserte la correa en el eje del trinquete
y tire rmemente. Enrolle el trinquete de modo que la red se superponga.
C. Desarme los rieles de la la cubierta y deslice a través de bolsas de tela en cada pata y vuelva a conectar
con abrazaderas a cada pata.
Repita esto en otro lado. Empuje hacia abajo la cubierta de los rieles para apretar la tapa, antes de apretar
los tornillos completamente.
D. Revise y apriete los trinquetes y los rieles de cruz mensualmente para asegurar la tapa esté bien apretada.
NOTA: El logo de ShelterLogic
®
debe ser
orientada como se muestra a continuación.
9. INSTALACIÓN DE LA TAPA CON RIELES CUBIERTA
CORRECTO
INCORRECTO
RIELES DE
CUBIERTA
10115
Riel de
Cubierta
Riel de
Cubierta
13201
Soporte
Curvo
Intermedio
01010
01011
01010
01011
Abrazaderas del Riel de Cubierta
del Soportes Curvo Intermedio
10115
Riel de
Cubierta
13202
Soporte
Curvo de
Extremo
01011
01010
Abrazaderas del Riel de Cubierta
del Soporte Curvo de Extremo
Correas y Trinquetes para Asegurar la Cubierta
NOTA:
Todas las vistas de
detalle son desde el interior.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

ShelterLogic 70435 Owner's manual

Brand
ShelterLogic
Model
70435
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents