Page is loading ...
W10705200A
FRONT-LOADING MULTI-LOAD
COIN-OPERATED COMMERCIAL WASHER
(TOP DISPENSERS ONLY)
User’s Guide
WASHER SAFETY .................................................................................. 1
USING THE WASHER ..........................................................................2
SET-UP PROCEDURES ......................................................................4
MAINTENANCE .......................................................................................4
TABLE OF CONTENTS
www.maytagcommerciallaundry.com
WASHER SAFETY
2
WASHER SAFETY
USING THE WASHER
1. Before Washing
Sort garments according to the clothing manufacturer’s
recommendations. To avoid damage to the garments and
washer, make sure that there are not any foreign objects
such as nails, screws, needles, etc., in the load. Turn sleeves
of shirts, blouses, etc. inside out. For best results, unfold
garments and mix large and small pieces together.
2. To Open the Door
Open the door by pulling on the door handle, or by turning the
door handle to the right and pulling.
3. Loading the Washer
Proper wash cycle and wash temperature should be selected
based on the type of load. For best results, do not overload
the washer.
4. To Close the Door
Use the door handle to close the door. Turn the door handle
to the left, making sure the door is properly latched before
placing the washer into operation.
3
7. To Fill the Dispensers
The dispenser is located on the top of the washer.
POWER
WASH
NORMAL
DELICAT ES
SOIL LEVEL
EXTRA RINSE
TEMPERATURE
SELECT CYCLE PRICE
POWER WASH
NORMAL
DELICATES
ENGLISH ESPANOL
$2.75
$2.00
$2.00
NOTE: All rinses are in cold water.
An indicator on the display shows what stage the cycle is in at
all times.
See Programming Guide for instructions on modifying factory
settings as well as available programming and setup options.
Dispenser (on top of washer)
6. Option Selections
Options can be chosen by pressing one of 3 buttons on the
right hand side of the display.
See Programming Guide for instructions on modifying factory
settings as well as available programming and setup options.
8. Starting the Washer
Select the desired cycle by pressing the button for that cycle.
Select the desired options by pressing the buttons for those
options.
Insert payment needed for operation. The display shows the
amount remaining to be paid. If the display shows PRESS
START, the washer can be started.
Add detergents and other wash additives prior to selecting
a cycle (see Step 7 above).
The washer will not start until the door latches and the
“START” button is pressed. If the door is not closed, close
and latch the door, then press the “START” button again.
During the wash cycle, the cycle progress and estimated
time remaining will appear in the display.
Prewash – It is recommended you add detergent for
the prewash prior to starting the cycle.
Main Wash – Add powdered detergent or powdered
bleach detergent prior to starting the cycle.
Main Wash – Add liquid detergent or liquid bleach
detergent prior to starting the cycle.
Fabric Softener – Add fabric softener prior to starting
the cycle or before the final rinse.
NOTES:
• Use only High Efficiency (HE) detergents.
• Refer to the detergent manufacturer’s instructions for
proper dosing. Too much detergent can cause poor
wash results and excess sudsing.
• Make sure that the lid of the soap dispenser is closed
before starting the washer.
Control Panel with Cycles Shown
POWER
WASH
NORMAL
DELICAT ES
SOIL LEVEL
EXTRA RINSE
TEMPERATURE
PRICE: $2.75 SELECT OPTION OR
POWER WASH HOT
HEAVY
EXTRA RINSE
MINUTES
35
Control Panel with Options Shown
POWER
WASH
NORMAL
DELICAT ES
SOIL LEVEL
EXTRA RINSE
TEMPERATURE
5. Cycle Selections
The program can be chosen by pressing one of 3 buttons
on the left hand side of the display. Choose the correct cycle
depending on the type of fabric and desired wash temperature.
For washing cottons and linens, it is recommended to use
the Normal wash cycle.
MAINTENANCE
DAILY MAINTENANCE
• Keep the washer clean at all times. Do not allow residual soap
and any cleaners to remain on the washer cabinet or top for any
length of time.
• Clean the detergent dispenser at the end of each business day
as follows:
a. Detergent may be stuck to the detergent box liner. This can
be scraped loose by using a spatula.
b. Flush the loosened detergent with warm water.
• Check the drain valve daily to make sure it is not leaking during
operation. Also make sure the valve is opening properly.
• Clean the door lip seal of any remaining detergent or foreign
matter.
• Clean door glass of any accumulated debris.
• Once the washer has been properly cleaned, open the door and
the detergent dispenser to allow for air drying. Leave doors open
at night.
• At the end of each business day, it is recommended that you
disconnect the “main” water and electrical power source to
the washer(s). It is not necessary to shut off the water and
power to each individual washer.
• Check door lock functions.
• Reinstall all panels and reestablish all safety guards after
maintenance.
05/14
W10705200A Printed in the Czech Republic
® /™ ©2014 Maytag. All rights reserved.
Used under license in Canada.
9. End of Wash Cycle
The end of the cycle is indicated when the display shows
“0” minutes remaining. You can open the door when CYCLE
COMPLETED THANK YOU! appears in the display.
To Open the Door in an Emergency
During the wash cycle, the washer can be stopped by
pressing the red “Stop” button. The display will show the
status of the washer stopping. After the drum has stopped,
the water has been drained, and the door has been unlocked,
the display will flash OPEN DOOR.
If the door will not open after several minutes:
IMPORTANT: This procedure should only be done by a
qualified servicer.
Make sure that the drum has completely stopped and drained
before opening the door. Opening the door while there is still
hot water in the drum can cause serious burns. Make sure that
the remaining water has cooled down completely before you
open the door.
Should the door still fail to open, the door can be opened as
follows (power must be turned off):
1. Remove the front panel of the washer.
2. A door release button is located behind the black panel
on the left side. Remove the plastic clip attached to the
button. Push the button; then open the door.
3. Reinstall the plastic clip back onto the door release button.
4. Reinstall the front panel.
SET-UP PROCEDURES
Washer-related set-up
Adjust washer-related settings in the configuration menu.
Cycle-related set-up
Adjust cycle-related settings in the wash cycle menu.
Price-Related Set-Up
Adjust price-related settings in the price menu.
These adjustments must be made by authorized personnel.
For set-up instructions, see the Programming Guide.
/