Bolens 11A-414A065 Owner's manual

11A-414A065
Bolens
Brand
Bolens
Model
11A-414A065
Type
Owner's manual

This manual is also suitable for

The Bolens 11A-414A065 is a powerful and versatile lawn tractor that can handle a variety of tasks, from mowing large lawns to clearing snow in the winter. With its 11 horsepower engine and 42-inch cutting deck, the Bolens 11A-414A065 can quickly and easily mow even the largest lawns. Its sturdy frame and durable components make it ideal for tough jobs, while its ergonomic design and easy-to-use controls make it comfortable to operate.

The Bolens 11A-414A065 is a powerful and versatile lawn tractor that can handle a variety of tasks, from mowing large lawns to clearing snow in the winter. With its 11 horsepower engine and 42-inch cutting deck, the Bolens 11A-414A065 can quickly and easily mow even the largest lawns. Its sturdy frame and durable components make it ideal for tough jobs, while its ergonomic design and easy-to-use controls make it comfortable to operate.

Supplement Sheet
Date: 1-3-2007
Subject: Lower Handle Assembly
Models Affected: Various models
1/3/2007
FORM NO. 769-03038
The assembly instructions for attaching the lower handle may be different from
the instructions in the manual. Please read the information below to see if these
new instructions pertain to the unit you have purchased.
If each end of the rear door pivot rod contains two
holes, please follow the instructions provided in the
manual as shown below to attach the lower handle to
the handle mounting brackets.
Locate the hairpin clip attached to the pivot rod on each side of
the lower handle.
Remove the hairpin clip from this hole. Using a pair of pliers,
insert the clip into the hole closest to the bracket, Figure 1.
Repeat on opposite side.
Insert a carriage bolt from the hardware pack into the upper
hole on the handle mounting bracket as shown in
Figure 1. Secure with one plastic wing nut, also included in
the hardware pack. Repeat on opposite side.
2.
a.
b.
If the rear door pivot rod does not contain holes at each
end of the rod, please follow the instructions below
in place of those found in the manual. If the unit was
shipped with two hairpin clips, please disregard these
pins.
To assemble the lower handle, follow these steps:
Place ends of the lower handle onto the handle brackets,
Figure 2.
Secure using carriage bolts and wing nuts provided in the
hardware pack, Figure 2.
2.
a.
b.
Wing Nuts (2)
Hardware Pack
Carriage Bolts (2)
A
B
Wing Nuts (2)
Hardware Pack
Carriage Bolts (2)
Figure 1: Attaching the lower handle to the mounting brackets
using the wing nuts, bolts, and hairpin clips.
Figure 2: Attaching the lower handle to the mounting brackets
using the wing nuts and bolts.
Holes in rear
door pivot rod
Hoja de suplemento
Las instrucciones de asamblea para unir la manija más baja pueden ser diferen-
tes de las instrucciones en el manual. Lea por favor la información abajo para ver
si estas nuevas instrucciones pertenecen a la unidad que usted ha comprado.
Si cada final de la vara de pivote de puerta trasera
contiene dos agujeros, por favor siga las instrucciones
proporcionadas en el manual como mostrado abajo
para atar el mango inferior a los soportes de montaje
de mango.
Si la barra trasera de pivote de puerta no contiene
hoyos en cada fin de la barra, siguen por favor las
instrucciones abajo en lugar de ésos encontraron en
el manual. Si la unidad fue enviada con dos clipes de
horquilla, desatiende por favor estos alfileres.
Localice el pasador de horquilla en un orificio en el pasador
soldado a cada lado de la manija inferior.
Saque el pasador de horquilla de este orificio. Usando las
pinzas, inserte el pasador de horquilla en el agujero interno
del pasador soldado. Repita por el otro lado.
Inserte el bulón de carro del paquete de hardware en el
orificio superior en el soporte de montaje de la manija. Sujete
con una tuerca plástica de mariposa, que también se incluye
en el paquete de hardware. Repita del otro lado con los
elementos restantes del paquete de hardware.
2.
a.
b.
Para reunir el mango inferior, siga estos pasos:
Finales de lugar del mango inferior en los soportes de
mango, la Figura 2.
El carro de utilización seguro se escapa y tuercas de
mariposa proporcionadas en el paquete de hardware, la
Figura 2.
2.
a.
b.
A
B
La figura 1: Atadura del mango inferior a los soportes de montaje
usando las tuercas de mariposa, cerrojos, y clips de horquilla.
Los agujeros en la puerta
trasera giran la vara
La figura 2: Atadura del mango inferior a los soportes de montaje
usando las tuercas de mariposa y cerrojos.
Fecha: 1-3-2007
Sujeto: más Abajo Asamblea de Mango Models
Modelos Afectados: Vario
1/3/2007
FORM NO. 769-03038
Tuerca de Mariposa
El Paquete de Hardware
El bulón de Carro
Tuerca de Mariposa
El Paquete de Hardware
El bulón de Carro
  • Page 1 1
  • Page 2 2

Bolens 11A-414A065 Owner's manual

11A-414A065
Bolens
Brand
Bolens
Model
11A-414A065
Type
Owner's manual
This manual is also suitable for

The Bolens 11A-414A065 is a powerful and versatile lawn tractor that can handle a variety of tasks, from mowing large lawns to clearing snow in the winter. With its 11 horsepower engine and 42-inch cutting deck, the Bolens 11A-414A065 can quickly and easily mow even the largest lawns. Its sturdy frame and durable components make it ideal for tough jobs, while its ergonomic design and easy-to-use controls make it comfortable to operate.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents