King VELOX P 226 User manual

Page is loading ...

SAFETY DIRECTION

1. For the first operation, it is advisable to read the manual carefully before hand

and keep it properly for future use.

2. Before the first operation, make sure the dust cup or the dust bag is properly

installed.

3. Make sure the power supply is 220-240V~ 50/60Hz

4. Do not vacuum water and inflammable material.

5. Do not vacuum burning material and ashes.

6. Do not use the machine without a motor protection filter filled.

7. Please change the dust bag immediately when it was damaged.

8. Do not store or use the machine close to high temperature places.

9. Dot not let children use the machine in case of danger.

10. If abnormal noise, smell, smoke or any other failure or breakage is found during

the operation, you should turn off the switch and unplug it. Then contact with your

service center for repair. Do not repair by yourself.

11. If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid a hazard.

12. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

13. Children should be supervised to ensure that they do not play with the

appliance.

14. The plug must be removed from the power socket before any maintenance

or replacement.

15. This appliance may be used by children aged 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or instruction concerning

safe use of the appliance and understand the hazards involved. Children should

not play with the appliance. Children should not carry out cleaning and user

maintenance without supervision

FAILURE CLEARANCE

Less vacuum power of the cleaner

1. The cleaner can be used as tip the rubbish out of the full dust cup or the dust bag.

2. If blockage is found in ground brush, hose or tubes, the machine can be re-operated

only after the blockage is cleared away.

MAIN BODY

1 Dust cup

2 Dust cup buckle

3 Machine lifting handle

4 Cord rewind button

5 Switch button

6 Air-out panel

7 Big roller

8 Main suction tube

9 Hose

10 Man-machine handle

11 Metal extension tube

12 Pneumaticfloor brush

HOW TO USE

How to assemble before use?

1. (Fig. 1) Attach hose to cleaner

Align the hose joint with the inlet of cleaner and insert it as shown.

To detach the hose, press the buckles of the joint and pull the hose out.

2. (Fig. 2) Attach elbow to metal extension tube

When connecting them, align and insert as shown.

3. (Fig. 3) Attach metal extension tube to floor brush

When connecting them, rotate the parts in opposite directions until secure.

4. (Fig. 4)Pull out power cord

The power cord can be pulled out to the red marking, but can never be pulled

beyond it. After use, unplug the machine first, and then press the rewind button

for power cord behind the cleaner.

6. (Fig. 5) Switch button

Plug the machine to power supply and push the switch button to control the

start and stop of the machine.

STEPS TO CLEAN DUST CUP

1. Take out the dust cup as shown in Fig. 6.

2. Gently push the dust dump button to dump dust as shown in Fig. 7, 8.

3. In case the suction power is insufficient when the waste has not reached MAX,

turn off the machine, repeat the above steps 1-2, detach dust cup cover and take

out the filter sponge for cleaning as shown in Fig. 8, 9.

4. In case of cleaning the inside of the dust cup, please operate according to the

following steps

1)Rotate the dust cup cover to detach it and take out the filter sponge (Fig. 9)

2) Take out secondary filter system (Fig. 10);

3) Remove dust press panel and filter net (Fig. 11);

4) Wash the separator under water tap and then dry it out;

5) Reassemble the dust cup and install it.

•Note: After cleaning the filter components, dry them first before putting back into the

machine for use. It is suggested to expose to sunshine for 24 hours until they are

completely dry. Make sure each component is back in place otherwise it may cause

malfunction; do not allow water to get into the electrical components otherwise it may

cause malfunction.

WARNING

The plug must be removed from the power socket before any maintenance or

replacement.

If the power cord is damaged, replace them only by the factory or maintenance

center or similarly qualified persons.

Page is loading ...

King VELOX P 226 User manual

King VELOX P 226 User manual

in other languages

Related papers

Other documents