Ripmax Sky Spy A-ARTF68752 User manual

Fuselage Length

Overall Height

Main Rotor Diameter

Total Weight

550mm

220mm

430mm

443g

Main Motor 370 x 2

Charging Time 150 Mins Approx

Flying Time 8~12 Minutes

Li-Po Battery 7.4V 1500mAh

This helicopter is equipped with a

removable aerial camera

R/C Helicopter

Transmitter

Video Transmitter

7.4V Li-Po Battery

USB Cable

AC Charger

Spare A&B Main Blades

Spare Tail Rotor

1

Name

Quantity

Name

Quantity

4 Channel Aerial

Photography R/C

Helicopter with

Real Time Video

Please read this Instruction Manual before operation. Please pay particular attention

to the CAUTION information

Part Number: A-ARTF68752

R/C Helicopter with wireless photography function

Record still images and video to view in real-time on the transmitter’s display

Instruction Manual

1

2. KIT CONTENTS

1. TECHNICAL SPECIFICATION

2

Move the ON/OFF

Switch to the OFF

Position when

Charging

Helicopter

Aerial Camera

Wireless Video

Transmitting Device

Transmitter with

Real-Time Video Display

AC Charger

3. FITTING THE BATTERIES AND CHARGING THE HELICOPTER

2. KIT CONTENTS (CONTINUED)

1. Loading the batteries: Remove the single screw retaining the battery cover. Now remove the

transmitter’s battery cover. Load 6 x AA batteries (not included) ensuring that the correct polarity

is observed.

2. Ensuring that the helicopter is switched off, connect the plug at the end of the charger’s lead in the

helicopter’s battery socket. Now plug the charger into a mains wall socket. When charging, the LED



When the battery is fully charged, the LED indicator will turn green. The helicopter is now ready



This R/C helicopter uses a Lithium Polymer battery. Please pay attention to the following safety items

below.

CAUTION

If you do not intend using

the helicopter for a long

time, ensure the power

switch is in the OFF position

and remove all batteries

from inside the transmitter.

 Do not expose the battery to high temperatures - it may ignite

or explode

 Do not drop the battery or expose it to any harsh impact

 Do not allow the battery to get wet

 Store the battery in a dry and cool place

 Only use the charger supplied with this product to charge the

battery

 Do not attempt to disassemble the battery

 Do not charge unattended

3

4. TRANSMITTER KEY FUNCTIONS

.

If you do not need to display

realtime images on the

transmitter’s display, just

press the ON/OFF switch for

the screen on the right hand

corner of the transmitter to

save power. Press the switch

once and it will turn OFF,

press it again and it will turn

ON.

 

 

 

 If possible, it is recommended the helicopter is



from people, obstacles and pets

Photograph

Button

Power

Switch

2.4 Inch

LCD

Power Switch

for LCD

5. FLYING ENVIRONMENT

Left/Right

Trim

Forwards/

Backwards

Trim

Combined

control stick

- Forwards/

Backwards

and Left/

Right

Display of

Transmission Status

Throttle Display

in Percentage

Increments

Video Mode

Enabled Symbol

Camera Mode

Enabled Symbol

Left/Right Trim

Display

Forward/Backward

Trim Display

Forward/Backward and

Left/Right Control

Display

Display of Helicopter’s

Control Channel

Mode Display

Display of Throttle and

Yaw Control

Throttle Trim Display

Left/Right Yaw Trim

Display

Display showing both

Low Speed (L) and High

Speed (H) Operating Mode

Display of the Helicopter

Whilst Flying

Throttle

High/Low

Transmitter Battery

Power Indicator

Distance of

30-100m

Distance of 30-100m

Distance of

30-100m

Distance of

30-100m

After the model is started, please

do not touch the rotating parts

(including gear, main rotor, etc) as

it may cause injury.

During or immediately after

use, the motor will be very

hot. Avoid touching it.

High

Temperature

Motor

6. SAFETY PRECAUTION

The transmitter’s Left/Right steering control lever can be switched as per the

user’s wishes by simply pressing down the right control lever. By doing so, the

function of the original left control steering will be shifted to the right control

steering. Press it once again and it will return to left control steering.

8. OPERATION

4

Place the helicopter carefully on the ground, turn the power switch



helicopter with the helicopter’s tail pointing towards you. Ensure

the transmitter’s throttle is closed and then turn the transmitter ON.

When the transmitter’s LED illuminates, you are ready for take off!

CAUTION

7. PREPARATION BEFORE FLYING

If the transmitter light



that the transmitter batteries

are running out of power

and consequently will need



Bank Left

Bank Right



control lever to the left. This will

make the helicopter bank to

the left.



control lever to the right.

This will make the helicopter

bank to the right.

Bank Left

Push the control

lever to the left

Bank Right

Push the control

lever to the right

Forwards

Backwards

Yaw

Ascending

Descending

When ascending or descending,

push the control lever forwards;

the rotating speed of the main

rotor will increase and the

helicopter will ascend.

When the throttle stick is pulled

backwards the helicopter will

descend as the rotating speed

of the main rotor will reduce.



right control lever to the left will

cause the nose of the helicopter

to turn left.



control lever forwards, the nose

of the helicopter will move

downward and the helicopter

will travel forwards.



control lever backwards, the

nose of the helicopter will rise

and the helicopter will travel

backwards.



right control lever to the right will

cause the nose of the helicopter

to turn right.

Forward/Backward

Pull the Control

Lever backward

Forward/Backward

Push the Control

Lever forward

Left/Right Control Lever

Push to the Right

Ascending

Push the control

lever forwards

Descending

Pull the control

lever backwards

Left/Right Control Lever

Push to the Left

Please be sure to carry out the initial binding of the helicopter to the transmitter by following the steps

below

1. Firstly, please switch the power to the helicopter and transmitter OFF.





3. Ensure the throttle on the transmitter is in its lowest position (stick pulled back) and then switch

ON the transmitter. An LED light will indicate the transmitter is ON. A buzzer will send out a ‘‘di di”

sound to show that a bind is in progress. When the bind process (which is automatic) is complete,

the sound will stop. DO NOT switch off either the helicopter or transmitter, as this will lose the

binding process and you will need to begin again.

4. The helicopter is now ready for use, assuming it has not been turned OFF after this process.

(Simply repeat the steps each time the helicopter is switched ON).

5. When using multiple helicopters at the same time, ensure each one is bound in turn, but DO NOT

switch any OFF.

10. BINDING THE TRANSMITTER TO THE HELICOPTER

First of all, switch

the Helicopter ON

9. FLYING PRACTICE

5

1 2

Switch ON

the Power

with the

throttle stick

in the low

position

To maximise your enjoyment of this model, why not practice

these four manoeuvres?

Rotate Left or Right

Landing in a precise spot



pattern which as your skill

develops, can be turned into

a circle.

Now that your skill has

developed further, try



11. CONNECTING THE CAMERA TO THE HELICOPTER

1 2

3

4

Use the data cable included to connect the

helicopter with the aerial camera.

Switch on the helicopter

and the aerial camera

Switch ON the transmitter and

complete the necessary steps

required to bind the helicopter as

outlined on the previous page.

By pressing the photograph button, the camera will

receive a transmitted signal indicated by the LED



If the photograph button is pressed for more than 1.5

seconds, the LED will glow signifying the activation of

VIDEO mode.

Pressing the photograph button again whilst recording

will FINISH the recording.

Photograph

Button

Power

Switch

Pull out the connecting data cable between the helicopter



to push up the camera latch which holds the camera in

place and then slide it out towards the tail to separate the

camera from the helicopter

Press the Recording

button

Pull the switch to the

left to turn ON the power

Photograph Button

AV Output jack

USB Connecting Port

Power Switch

Memory Card

Port

Lens

Microphone

Recording

Indicator

12. INDEPENDENT USE OF THE DIGITAL CAMERA



times and then stop. This means that the camera is ready and in ‘Standby

Mode’. You are now able to press the shutter button and take a picture.



has been taken. If you hold down the shutter button for more than 1.5

seconds, the video mode will be activated and a video will start recording.

During the course of recording, if you press the shutter button once more,

the video will stop recording. Should you need to change the date or time,

please modify the ‘Time’ text document located in the root directory of the

Micro SD card and edit it such that the current date and time are correct.



updated before restarting the camera.

Video/Photographic

State Indicator

6

13. READING THE AERIAL PHOTOGRAPHY DATA & CHARGING

Disconnect the included USB cable from the helicopter and connect



“removable disc” in the “My Computer” directory. Double click it to

read the data inside the aerial camera. Please copy the aerial

photography data from the disk to the computer and then browse to



the USB port immediately as the USB port also charges the camera.

When charging is underway, the LED indicator on the camera will



Should you be unable to receive any real-time video, please consult the following list

1) Check if the 2.5mm video transmitter plug has been inserted into the AV output jack on the aerial

camera.

2) Check if the red LED on the transmitter is ON or not. If it is not ON, it means the plug is not

connected correctly in the AV port. Unplug and then re-connect. Should the problem not be



charging.

3) Check if the transmitting frequency on the video transmitter is the same as the receiving frequency.

4) If unable to receive any images, this may be due to the DIP switch having been set

incorrectly.

.

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

A channel B channel C channel

D channel

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

A channel B channel C channel D channel

14. REAL TIME AUDIO & VIDEO DURING FLIGHT

1 2

3

4

Fix the video transmitter on the tail boom and

then insert the 2.5mm plug into the AV output jack

of the aerial camera. Switch on the camera. This

time the red LED on the video transmitter will be

ON, meaning it has started working.

Push up and down the DIP switch on the

transmitter to set the frequency. For this

helicopter, there are four transmitting frequencies

available. Set the DIP switch as shown in the

illustration.

The DIP switches on the back of the transmitter

are for setting the receiving frequency. Ensure

you match the receiving and transmitting

frequencies. If the transmitter is set to Channel

A, then so too must the receiver.

LCD Power

Switch

Switch ON the

transmitter’s power

switch. If the

transmitting frequency

is the same as the

receiving frequency the

screen will show a real-time image. Please

press the ON/OFF button to switch OFF the

display screen in order to save power when

you do not wish to have any live video image

shown.

7

8

15. SPARE PARTS LIST

Actual parts supplied may differ

slightly from photographs shown.

O-JY6875017

LiPo Battery

Z-JY6875021

Main Inner Shaft

Z-JY6875022

Tail Boom

Z-JY6875023

Flybar

Z-JY6875024

Main Outer Shaft

Z-JY6875037

Horizontal Tail

Z-JY6875038

Vertical Fin

Z-JY6875040

Lower Main Frame Set

O-JY6875042

Mains Charger

P-JY6875045

Aerial Photography

Module

Z-JY6875025

Tail Boom Support

Z-JY6875030

Lower Blade Hub

Z-JY6875034/35

Main Gear Set

Z-JY6875001

Canopy

Z-JY6875003

Main Chassis

Z-JY6875004

Landing Gear

Z-JY6875006/7

Main Blade Set (A+B)

(Upper and Lower)

1 2 3 4 5

6 7 8 9 10

11 12 13 14 15

16 17 18 19 20

21 22

Distributed by:

241 Green Street,



EN3 7SJ

Ltd.

P-JY6875046

2.4GHz Wireless

Transmitter

Z-JY6875027

Flybar Linkage

Z-JY6875029

Servo Linkage

Z-JY6875036

Tail Blade



http://www.bmfa.org/publications/fpv.html

http://www.fpvuk.org/fpv-law/resources/

Page is loading ...

Ripmax Sky Spy A-ARTF68752 User manual

Ripmax Sky Spy A-ARTF68752 User manual

in other languages

Related papers

Other documents