Red Digital Cinema Epic 6.3 User manual

WEAPON | EPIC-W

HELIUM 8K S35 | V6.3

RED.COM

WEAPON/EPIC-W (HELIUM 8K S35)

OPERATION GUIDE

Table of Contents 2

Disclaimer 4

Copyright Notice 4

Trademark Disclaimer 4

Compliance Statements 4

Safety Instructions 6

Battery Storage and Handling 8

Shipping Disclaimer 9

1 RED Product Introduction 10

Read Before You Shoot 10

R3D File Format and REDCODE 10

Shoot For Video and Stills 11

Post Production with REDCINE-X PRO 11

HDRX and MAGIC MOTION 11

Additional Resources 12

2 Camera System Components 13

Additional Resources 13

BRAIN 13

REDMINI-MAG System 18

Expanders 19

Power Modules 25

REDBatteries and Chargers 26

Displays and Electronic Viewfinders 27

LEMOAdaptors 32

Camera Control Modules 33

Lens Mounts 36

Interchangeable OLPFs 37

Rails, Mounts, Tactical Gear, and Cables 37

3 Basic Operations 38

Power Operations 38

Configure Your Camera 41

Interchangeable OLPF System 47

Use a Tripod or Monopod 49

Video Monitor Outputs 50

Record 51

4 Basic Menus and Controls 53

GUI Menu Introduction 53

Upper Status Row (Basic Menu) 54

Live Action Area 58

Lower Status Row 60

WEAPON/EPIC-W OPERATION GUIDE

TABLE OF CONTENTS

Navigation Controls 66

5 Advanced Menus 75

Advanced Menus Overview 75

Access the Advanced Menus 75

Settings Menu 76

Media Menu 137

Playback Menu 138

Power Menu 143

HDRX Menu 144

Focus Menu 145

Exposure Assist Menu 151

Presets Menu 153

6 Record and Monitor Audio 156

Audio Overview 156

Set Up Audio 156

Control 157

Mix 160

Audio Output Options 160

Audio Meter (VU Meter) 161

Audio During Playback 162

7 Timecode, Genlock, Multi-Camera

Setup 163

Timecode 163

Genlock 166

Master/Slave Operation 170

Set Up Stereo/3D Configuration 175

Camera Array 176

Set Up Motion Control (MoCo) 177

Compatible Timecode Devices 178

Compatible Genlock Devices 179

8 Upgrade Camera Firmware 180

Verify Current Camera Firmware 180

Upgrade Camera Firmware 180

9 Camera System Maintenance 182

BRAIN and Accessory Exterior Surfaces 182

Clean EVF Screen 183

Clean LCD Screens 183

Water Damage 184

Adjust Back Focus 184

10 Troubleshoot Your Camera 185

Perform a Stress Test 185

General Troubleshooting 186

Error Messages 192

Media Bay and RED MINI-MAG Issues 194

Back Focus Lock 195

A Technical Specifications 197

WEAPON HELIUM 8K S35 Technical

Specifications 197

EPIC-W Technical Specifications 200

B Mechanical Drawings 203

WEAPON8K S35 BRAIN 203

EPIC-W BRAIN 208

C Input/Output Connectors 213

DSMC2 Base Expander 214

DSMC2 V-Lock I/O Expander 215

DSMC2 REDVOLT Expander 216

DSMC2 Jetpack Expander 217

DSMC2 Jetpack-SDI Expander 218

Record/Monitor Out Ports 219

Communication Ports 221

Audio Ports 231

Power Ports 233

D Lens Mounts and Lenses 240

Lens Mounts 240

Lenses 242

E Default Key Functions 254

Default Keys 254

F Menu Map 257

WEAPON/EPIC-W OPERATION GUIDE

DISCLAIMER

RED

®

has made every effort to provide clear and accurate

information in this document, which is provided solely for the user’s

information. While thought to be accurate, the information in this

document is provided strictly “as is” and RED will not be held

responsible for issues arising from typographical errors or user’s

interpretation of the language used herein that is different from that

intended by RED. All safety and general information is subject to

change as a result of changes in local, federal or other applicable

laws.

RED reserves the right to revise this document and make changes

from time to time in the content hereof without obligation to notify any

person of such revisions or changes. In no event shall RED, its

employees or authorized agents be liable to you for any damages or

losses, direct or indirect, arising from the use of any technical or

operational information contained in this document.

For comments or questions about content in this document, please

send a detailed email to OpsGuides@red.com.

COPYRIGHT NOTICE

All trademarks, trade names, logos, icons, images, written material,

code, and product names used in association with the accompanying

product are the copyrights, trademarks, or other intellectual property

owned and controlled exclusively by RED.COM, INC. For a

comprehensive list, please see www.red.com/trademarks.

TRADEMARK DISCLAIMER

All other company, brand, and product names are trademarks or

registered trademarks of their respective holders. RED has no

affiliation to, is not associated with or sponsored by, and has no

express rights in third-party trademarks. Adobe and Adobe Premiere

Pro are registered trademarks of Adobe Systems Incorporated. AJA

is a registered trademark of AJA Video Systems, Inc. Cooke and S4/i

are registered trademarks of Cooke Optics Limited. DaVinci is a

registered trademark of Blackmagic Design in the U.S. and other

countries. Distagon, Makro- Planar, and Otus are registered

trademarks of Carl Zeiss AG. Fujinon is a registered trademark of

FUJIFILM CORPORATION. HDMI is a registered trademark of HDMI

Licensing LLC in the United States and other countries. Leica is a

registered trademark of Leica Microsystems. Loctite is a registered

trademark of Henkel AG & Company KGaA. Nikkor and Nikon are

registered trademarks of Nikon Corporation. Canon is a registered

trademark of Canon, U.S.A. Apple, Macintosh, Final Cut Pro, and

QuickTime are registered trademarks of Apple Inc. in the U.S. and

other countries. Windex is a registered trademark of S. C. Johnson &

Son, Inc. Windows is a registered trademark of Microsoft Corporation.

LEMO is a registered trademark of LEMO USA. Sony is a registered

trademark of Sony Corporation. TORX is a registered trademark of

Acument Intellectual Properties, LLC in the United States or other

countries. IOS is a registered trademark of Cisco in the U.S. and

other countries. Avid is a registered trademark of Avid Technology,

Inc. DaVinci Resolve is a registered trademark of Blackmagic Design

in the U.S. and other countries. EDIUS Pro is a registered trademark

of Grass Valley. Vegas Pro is a registered trademark of Sony Creative

Software. IDX is a registered trademark of IDX Company, Ltd.

WEAPON/EPIC-W OPERATION GUIDE

COMPLIANCE STATEMENTS

INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS

This device complies with Industry Canada license- exempt RSS

standards RSS 139 and RSS 210. Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may

cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas

produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.Cet appareil

numérique de la classe B est conforme à la norme NMB-003 du

Canada.

FEDERAL COMMUNICATIONS COMMISSION (FCC)

STATEMENTS

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

In order to maintain compliance with FCC regulations, shielded cables

must be used with this equipment. Operation with non-approved

equipment or unshielded cables is likely to result in interference to

radio and TV reception. The user is cautioned that changes and

modifications made to the equipment without the approval of

manufacturer could void the users authority to operate this equipment.

NOTE: This device complies with Part 15 of the FCC Rules.

Operations subjected to the following two conditions (1) this device

may not cause harmful interference, and (2) this device must accept

any interference received, including that may cause undesirable

interference.

CAUTION: Exposure to Radio Frequency

Radiation.

The device shall be used in such a manner that the potential for

human contact is minimized

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed

and operated with a minimum distance of 20 cm between the radiator

and your body.

CAUTION: Regulations of the FCC and FAA

prohibit airborne operation of radio- frequency

wireless devices because there signals could

interfere with critical aircraft instruments.

CAUTION: If the device is changed or modified

without permission from RED, the user may void

his or her authority to operate the equipment.

AUSTRALIA AND NEW ZEALAND STATEMENTS

RED declares that the radio equipment described in this document

comply with the following international standards.

IEC 60065 - Product Safety

ETSI EN 300 328 - Technical requirement for radio equipment

RED declares digital devices described in this document comply with

the following Australian and New Zealand standards.

AS/NZS CISPR 22 – Electromagnetic Interference

AS/NZS 61000.3.2 – Power Line Harmonics

AS/NZS 61000.3.3 – Power Line Flicker

JAPAN STATEMENTS

This is a Class B product based on the

standard of the Voluntary Control Council

for Interference (VCCI) for information

technology equipment. If this equipment is

used near a radio or television receiver in a

domestic environment, it may cause radio

interference. Install and use the equipment

according to the instruction manual.

WEAPON/EPIC-W OPERATION GUIDE

EUROPEAN UNION COMPLIANCE STATEMENTS

RED declares that the

radio equipment

described in this

document comply with

the R&TTE Directive

(1999/5/EC) issued by

the Commission of the

European Community.

Compliance with this directive implies conformity to the following

European Norms (in brackets are the equivalent international

standards).

EN 60065 (IEC 60065) – Product Safety

ETSI EN 300 328 Technical requirement for radio equipment

ETSI EN 301 489 General EMC requirements for radio

equipment.

INFORMATION

Products with the CE marking comply with the EMC Directive

(2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by

the Commission of the European Community. Compliance with these

directives implies conformity to the following European Product Family

Standards.

EN 55022 (CISPR 22) – Electromagnetic Interference

EN 55024-1 (CISPR 24) – Electromagnetic Immunity

EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics

EN 61000-3-3 (IEC610000) – Power Line Flicker

EN 60065 (IEC60065) – Product Safety

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)

The Waste Electrical and Electronic

Equipment (WEEE) mark applies only to

countries within the European Union (EU)

and Norway. This symbol on the product and

accompanying documents means that used

electrical and electronic products should not

be mixed with general household waste. For

proper treatment, recovery and recycling,

please take this product to designated

collection points where it will be accepted

free of charge. Alternatively, in some

countries you may be able to return your

products to your local retailer upon purchase of an equivalent new

product.

Disposing of this product correctly will help save valuable resources

and prevent any potential negative effects on human health and the

environment, which could otherwise arise from inappropriate waste

handling. Please contact your local authority for further details of your

nearest designated collection point. Penalties may be applicable for

incorrect disposal of this waste, in accordance with you national

legislation.

For business users in the European Union, if you wish to discard

electrical and electronic equipment, please contact your dealer or

supplier for further information.

USAGE RESTRICTIONS FOR PRODUCTS THAT INCORPORATE

REDLINK

Products that fall into this category are denoted

by inclusion of the Class 2 identifier symbol

(exclamation mark in a circle) accompanying

the CE Mark on the products regulatory label,

example to the left.

FRANCE

Usage Restrictions - Geographic Area Where

Restriction Applies : France

For mainland France

2.400 - 2.4835 GHz (Channels 1-16) authorized for indoor use

2.400 - 2.454 GHz (Channels 1-10) authorized for outdoor use

Restrictions d’utilisation - Zone géographique où les restrictions

s’appliquent : France

Pour la France métropolitaine

2.400 - 2.4835 GHz (Canaux 1 à 16) autorisé en usage intérieur

2.400 - 2.454 GHz (canaux 1 à 10) autorisé en usage extérieur

NORWAY

This subsection does not apply for the geographical area within a

radius of 20 km from the centre of Ny-Ålesund

Dette gjelder ikke for det geografiske området innenfor en radius av

20 km fra sentrum av Ny-Ålesund

RESPONSIBLE PARTY

RED Digital Cinema

34 Parker

Irvine, CA 92618

USA

WEAPON/EPIC-W OPERATION GUIDE

SAFETY INSTRUCTIONS

DO NOT use the camera or accessories near water. Avoid

exposing your camera to moisture. The unit is not waterproof, so

contact with water could cause permanent damage to the unit as

well as electric shock and serious injury to the user. DO NOT use

the camera in the rain or under other conditions with high

moisture without appropriate protection, and immediately remove

power source if camera or accessories are exposed to moisture.

WARNING: To reduce the risk of fire or electric

shock, do not expose the camera to rain or

moisture.

DO NOT expose the camera to laser beams, as laser beams may

damage the sensor.

DO NOT expose your camera to excessive vibration or impact

(shock). Be careful not to drop your camera. Internal mechanisms

may be damaged by severe shock. Mechanical alignment of

optical elements may be affected by excessive vibration.

ELECTROMAGNETIC INTERFERENCE: The use of devices using

radio or other communication waves may result in the malfunction

or interference with the unit and/or with audio and video signals.

Clean only using a dry cloth. When cleaning your camera,

remember that it is not waterproof and moisture can damage

electronic circuitry. DO NOT rinse or immerse any element of the

camera, lens or other accessory, keep them dry at all times. DO

NOT use soaps, detergents, ammonia, alkaline cleaners, and

abrasive cleaning compounds or solvents. These substances may

damage lens coatings and electronic circuitry.

Maintain sufficient ventilation—DO NOT block any ventilation

openings or obstruct cooling fan airflow.

CAUTION: Proper camera ventilation requires a

minimum 0.5" (1.25 cm) clearance between the

camera ventilation openings and external

surfaces. Verify that objects that can block the fan

intake and exhaust ports do not impede airflow.

Failure to permit adequate airflow may result in

overheating of the camera, degraded operation

and in extreme situations, damage to the camera.

DO NOT operate or store near any heat sources such as

radiators, heat registers, stoves, or any other apparatus that

produce heat. Store in a protected, level and ventilated place.

Avoid exposure to temperature extremes, damp, severe vibration,

strong magnetic fields, direct sunlight or local heat sources during

storage. Remove any batteries from the camera before storage.

Recommended storage and usage temperatures for your camera,

lenses and other accessories are:

Operating range: 0°C to 40°C (32°F to 104°F)

Storage range: –20°C to 50°C (–4°F to 122°F)

If there are any performance issues with your camera or

accessories when operating within this temperature range, please

file a support ticket on https://support.red.com.

Modules and expanders, expanders, and lens mounts are NOT

HOT SWAPPABLE, meaning you cannot remove or install these

items while the camera is turned on. Before installing or removing

these items, you MUST turn off the camera. Failure to do so may

result in damage to the item or camera that is not covered under

warranty.

DO NOT bypass the third prong of the grounding-type plug on the

power cord of the DSMC AC Power Adaptor. A grounding-type

plug has two blades and a third “grounding” prong. The third

prong is provided for your safety. A grounding-type plug shall be

connected to an outlet with a protective earthen connection. If the

grounding-type plug does not fit into your outlet, do not attempt to

modify the plug or outlet, consult a qualified electrician.

Protect all power cords from being pinched, walked on or driven

over by a vehicle. Replace any power cords suspected of

sustaining damage due to crushing or other forms physical

damage.

Products marked with this symbol are class 2

devices. These devices are not provided with a

grounding type plug.

CAUTION: The power cord plug for the DSMC

AC Power Adaptor is used as the power

disconnect. To disconnect all power from the

DSMC AC Power Adaptor, unplug the power cord

plug from the wall outlet. During use, the power

cord plug should remain easily accessible at all

times.

Lithium-ion batteries may be subject to special handling

requirements pursuant to federal and local laws. Please refer to

specific shipping instructions included with your battery regarding

proper transport of your battery. Do not handle your battery if it is

damaged or leaking. Disposal of batteries must be in accordance

with local environmental regulations. For example, California law

requires that all rechargeable batteries must be recycled by an

authorized recycle center. Storing batteries fully charged or in

high temperature conditions may permanently reduce the life of

the battery. Available battery capacity may also be temporarily

lessened after storage in low temperature conditions.

WEAPON/EPIC-W OPERATION GUIDE

WARNING: DO NOT expose the battery to

excessive heat.

WARNING: Danger of explosion if an incorrect

battery is charged with the RED Charger or is

used to power the camera and accessories.

Replace only with the same or equivalent type

battery.

CAUTION: Refer all service and repair to

qualified RED service personnel. To reduce the

risk of electric shock, and damage to the

camera or accessories, DO NOT attempt to

perform any servicing other than any procedures

that are recommended in the operating

instructions.

INDOOR USE ONLY: Products marked with this

symbol are designed for use indoors only.

BATTERY STORAGE AND HANDLING

WARNING: Failure to read, understand, and

follow these instructions may result in overheating,

chemical leakage, smoke emission, fire, or other

potentially harmful results.

Always follow proper battery handling and storage practices.

Improper handling and/or failure to abide by proper storage

instructions may cause permanent damage to batteries, or

degrade battery charge holding capacity. Improper handling

practices or failure to comply with instructions may also put you at

risk.

Lithium-Ion batteries, like the REDVOLT

®

, REDVOLT XL, and

RED BRICK

®

, self-discharge over time. When storing for long

periods of time, store batteries separately from the camera or

charger and remember to charge batteries to a capacity level of

40% to 60%. If batteries will be stored for long periods of time,

RED recommends that you check the charge level at least once

every six (6) months, and recharge batteries to a capacity level of

40% to 60%.

When not in use, remove the battery from the camera or charger

and store the battery in a cool, dry place. Avoid extreme hot

temperatures (such as inside a hot car), corrosive gas, and direct

sunlight. The optimal storage temperature for batteries is between

–20°C to 20°C (–4°F to 68°F).

WARNING: Batteries stored in a discharged state

for long periods of time may self-discharge and

lose the ability to hold a charge.

WARNING: If recharging operation fails to

complete even when a specified recharging time

has elapsed, immediately stop further recharging.

DO NOT store batteries in a fully charged state for extended DO

NOT store batteries in a fully charged state for extended periods

of time.

DO NOT store batteries in a fully discharged state for extended

periods of time.

DO NOT store batteries in the camera, in a camera module, or in

a charger for extended periods of time.

DO NOT use batteries for purposes other than their intended use.

DO NOT store batteries in extreme hot or cold temperatures.

DO NOT store batteries in direct sunlight.

DO NOT use third-party chargers with your RED batteries.

DO NOT disassemble or modify the battery.

DO NOT overcharge batteries. Overcharging may increase

internal temperature beyond the recommended limits and cause

permanent damage to the battery.

DO NOT connect the positive (+) and negative (–) terminals to a

metal object such as a wire.

WEAPON/EPIC-W OPERATION GUIDE

DO NOT transport or store the battery together with metal objects

such as jewelry, hairpins, etc. as they may generate heat if they

come into contact with the battery.

DO NOT discard the battery into fire or heat.

DO NOT store, use, or recharge the battery near a heat source

such as a fire or a heater.

DO NOT allow the battery to get wet.

DO NOT pierce the battery with pointed or other sharp objects.

DO NOT step on, throw, or strike the battery with a hammer.

DO NOT use a battery that appears to be deformed or damaged.

DO NOT directly solder the battery.

DO NOT put the battery into a microwave oven or a pressurized

container.

DO NOT use or subject the battery to intense sunlight or hot

temperatures such as in a car in hot weather.

DO NOT use it in a location where static electricity may be

present.

DO NOT exceed the recharging temperature range of 0˚C to 40˚C

(32˚F to 104˚F).

RED recommends that you only use RED chargers to recharge

RED batteries.

Store the battery in a location where children cannot reach it.

If the battery leaks or gives off a bad odor, discontinue use

immediately.

If the battery gives off an odor, generates heat, becomes

discolored or deformed, or in any way appears abnormal during

use, recharging or storage, immediately remove it from the

equipment or battery charger and discontinue use.

If electrolyte begins leaking from the battery and comes into

contact with your skin or clothing, immediately wash it away with

running water. Failure to do this may result in skin inflammation.

If the battery leaks and the electrolyte reaches the eyes, do not

rub them. Instead, rinse the eyes with clean running water and

immediately seek medical attention. Failure to do this may result in

eye injury.

If you find discoloration, a bad odor due to leakage, overheating

and/or other irregularities when using the battery for the first time,

contact your Bomb Squad representative immediately.

NOTE: For more information regarding RED

battery charging and instructions for care, please

refer to our Terms and Conditions.

SHIPPING DISCLAIMER

Shipment of Lithium Ion cells and batteries is subject to national and

international shipping requirements. A Class 9 Certified shipper is

required to transport these products within the United States.

REDVOLT, REDVOLT XL, and RED BRICK batteries are considered

Dangerous Goods. Other products such as REDVOLT AA and RED Li

7.2V batteries may also be classified as Dangerous Goods when

purchased in bulk. Applicable laws prohibit the shipping of batteries

that are physically damaged. We urge you to look into the formal rules

and regulations of shipping Class 9 Dangerous Goods prior to

preparing your shipment. For more information on these regulations,

please visit www.iata.org and www.dot.gov.

For more information, see our FAQs for Dangerous Goods (Regulated

Items).

WEAPON/EPIC-W OPERATION GUIDE

1

RED PRODUCT

INTRODUCTION

The WEAPON

®

HELIUM™8K S35 and RED EPIC-W™ HELIUM 8K S35 cameras are part of the second-generation

Digital Still and Motion Camera (DSMC2™) system. The DSMC2 family, a subset of the DSMC

®

family, includes

WEAPON, EPIC-W, SCARLET-W, and RED RAVEN

®

. With an ultra-high megapixel count, high frame rate, significant

processing power, high dynamic range, and the advantages of a raw file format, each camera offers the ability to

simultaneously capture video and stills.

This guide is for WEAPON HELIUM 8K S35 and EPIC-W HELIUM 8K S35 only. This section introduces the imaging

capabilities and advanced features of the WEAPON HELIUM 8K S35 and EPIC-W HELIUM 8K S35 system. For

information about other cameras, go to RED Downloads at www.red.com/downloads.

The WEAPON HELIUM 8K S35 and EPIC-W HELIUM 8K S35 system includes the following cameras (organized by

sensor type):

SENSOR TYPE CAMERA

HELIUM 8K S35 RED EPIC-W with HELIUM 8K S35 sensor

WEAPON with HELIUM 8K S35 sensor

WEAPON with HELIUM 8K S35 sensor [Limited Edition]

READ BEFORE YOU SHOOT

Read this operation guide carefully and in its entirety before assembling or operating your camera or other RED

accessories. In addition to this document, RED offers the following operation guides for the camera system:

DSMC Power Operation Guide

DSMC Media Operation Guide

To download RED operation guides, go to RED Downloads at www.red.com/downloads.

R3D FILE FORMAT AND REDCODE

All videos and frames are recorded to the R3D

®

file format. The R3D file format was developed by RED to provide an

efficient and manageable RAW video data format that promotes advanced post production editing capabilities. In the

R3D file format, the digital image received from the sensor is formatted as a pixel-defect corrected (but in all other

aspects unprocessed) 16-bit per pixel RAW data frame. Each RAW frame, or sequence of RAW frames in a clip, is

compressed using a proprietary wavelet based REDCODE

®

RAW compression, then stored to a RED MINI-MAG

®

.

RAW data is recorded independently of any RGB domain color processing such as ISO, White Balance, or other RGB

color space settings. Instead, color parameters are saved as reference metadata; that is, color is not burned into the

recorded RAW data. This recording technique promotes flexibility in RGB color processing, which can be deferred to

post production or adjusted in the field, without affecting the recorded RAW data image quality or dynamic range.

REDCODE is a visually lossless, wavelet-based compression codec that reduces R3D RAW files into a manageable

size, allowing longer recording times on media. The ability to compress RAW data is one of the significant

technologies that RED has brought to the industry.

For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.

NOTE: REDCINE-X PRO

®

can create and export .RMD “Look” files which may then be imported as camera monitor

path color processing presets. This information is stored as reference metadata, so that these color processing

choices can be the default values used in post production. For more information, go to "Looks" on page154.

SHOOT FOR VIDEO AND STILLS

High resolution video, such as the digital footage captured by the camera, has surpassed the detail necessary to

produce professional full-sized prints. Because of the ability to record at high frame rates and resolution, the camera is

ideally suited to capture video and still images, simultaneously.

The camera is equipped with a Stills mode that makes it easier to capture stunning images. With presets optimized for

stills and Swipe-Up Shortcuts for the RED Touch display, switching from Motion mode to Stills mode is seamless.

Using REDCINE-X PRO, or other editing applications supporting the RED SDK, you can pull full resolution still images

from R3D files.

POST PRODUCTION WITH REDCINE-X PRO

REDCINE-X PRO is a professional one-light coloring toolset, equipped with an integrated timeline and a post effects

software collection that provides the ideal environment to review recorded footage, edit metadata, organize projects,

and prepare your R3D files. Use either REDCINE-X PRO or a compatible third-party non-linear editing (NLE) application

to edit R3D files.

RED TETHER, included in REDCINE-X PRO, allows you to record footage from your camera directly to a computer or

an external drive. Using tethering bypasses the need to record to an SSD and offload to a computer later, saving you

time. The latest version of REDCINE-X PRO and the REDCINE-X PROOperation Guide are available for download at

RED Downloads at www.red.com/downloads.

NOTE: RED TETHER is included in REDCINE-X PRO build 35 or later.

HDRX AND MAGIC MOTION

HDRX

®

extends dynamic range up to six (6) stops by simultaneously capturing two (2) images of identical resolution

and frame rate. The first image is a normally exposed track (A-track), while the second is an underexposed track (X-

track) with an exposure value that reflects the additional stops of highlight protection. These tracks are “motion-

conjoined” during recording, leaving no time gap between the two (2) exposures. This is different from traditional

alternating exposures, which have small gaps between tracks, producing unwanted motion tracks.

MAGIC MOTION

MAGIC MOTION is a post production method that combines two (2) HDRX tracks to create an image with both natural

motion blur (from the A-track) and sharper reference (the X-track). MAGIC MOTION produces an image with an

extraordinary dynamic range that is not available with any other motion capture camera.

Shooting at 24 fps with a 180° (1/48 sec) shutter on traditional film or digital cameras produces motion blur throughout,

which is not the way the human eye observes motion. For example, ask someone to swing their arm. What you would

observe in a traditional recording of this action is constant motion blur until the arm stops. However, what your eye

sees is both motion blur and a sharper reference of the arm throughout the motion path. MAGIC MOTION creates an

image that matches the natural motion observed by the human eye.

WEAPON/EPIC-W OPERATION GUIDE

ADDITIONAL RESOURCES

The following resources offer additional information about RED, the DSMC

®

system, and the RED community:

RED.com: Check the official RED website for the latest information about RED products.

RED Learn Articles: RED offers in-depth technical articles about RED cameras, post-production, and digital

cinematography.

RED Downloads: Go to RED Downloads to download the latest firmware, operation guides, and post-production

software.

DSMC Toolkit: Go to RED Downloads to find the DSMC Toolkit, which offers many helpful tools and resources to

customize and improve your camera workflow.

RED Support: Check the RED SUPPORT site for FAQs, or to file a support ticket.

Bomb Squad Support: For more information, contact your Bomb Squad representative.

In-Camera Help: Select the Help button on an in-camera screen to open up the help for that screen.

REDUSER: Discuss all things RED on the REDUSER third-party forum.

WEAPON/EPIC-W OPERATION GUIDE

2

CAMERA SYSTEM

COMPONENTS

NOTE: Modules and lens mounts are NOT HOT SWAPPABLE, meaning you cannot remove or install these items

while the camera is turned on. Before installing or removing these items, you MUST turn off the camera. Failure to do

so may result in damage to the item or camera that is not covered under warranty.

NOTE: Availability of components listed in this chapter is subject to change at any time.

ADDITIONAL RESOURCES

For more information on power and media, see the following guides, available at www.red.com/downloads:

DSMC Power Operation Guide

DSMC Media Operation Guide

BRAIN

Figure: WEAPON8K S35

The DSMC BRAIN

®

is the image processing center of the camera system and supports power, media, and other

modules.

The only ports on the BRAIN are the DSMC2™ Top Handle port and EVF/LCD ports. A port expander or power

module is required to power the camera. All other input/ouput (I/O) ports are available only via expanders and other

modules. This modular approach allows you to customize your camera and make use of the ports that are most

applicable to your needs.

The RED

®

Tactical Hand Controller (T.H.C.) cannot pair directly to the camera. To use the T.H.C. with the camera, the

T.H.C. needs to be connected to the W.M.D. (either wired or wirelessly). For more information about the T.H.C., see

the RED 3-Axis System Operation Guide at www.red.com/downloads.

BRAIN CONTROL: PWR/REC KEY

Fully press and hold the PWR/REC key for two (2) seconds to turn on/off.

When the camera is on, fully press and then release the PWR/REC key to toggle record start/stop.

BRAIN LEDS

This section describes the LED functions for the camera.

NOTE: When the camera is powered only by battery and not AC power, the Power Status LED (PWR) on the expander

or module does not turn on. You can press the button on the battery to check the battery charge level.

LED COLOR/FLASHING DESCRIPTION

Power Status LED (PWR) Off Camera off

1

Green Camera on

Amber flashing Camera on; 5 to 10 min of battery time available

Amber Camera booting

Red flashing Camera on; < 5 min of battery time available

Red Camera shutting down

Record Status LED (REC) Off No media present

Green Ready to record

Amber Finalizing

Red flashing (slow) Media mounted with > 5% and ≤ 10% of media

space available

Red flashing (fast) Media mounted with ≤ 5% of media space

available

Red Recording

Power Status LED (PWR) and Record

Status LED (REC)

Both green flashing Firmware update in progress

Both red flashing Firmware update error

1. To prevent battery drain, the PWR LED does not illuminate when the camera is off and a power source is present.

WEAPON/EPIC-W OPERATION GUIDE

BRAIN CONNECTORS, FOCUS HOOK

Figure: WEAPON8K S35 BRAINPorts and Features

# PORT/ITEM DESCRIPTION

1 Primary

EVF/LCD Port

1

Mount a DSMC2 RED Touch LCD

2 Top Handle

Port

Mount the DSMC2 Top Handle or DSMC2 Outrigger Handle. This is the only mounting option

for the DSMC2 Top Handle or DSMC2 Outrigger Handle (it cannot be attached backward).

3 Secondary

EVF/LCD Port

1

Mount a DSMC2 RED Touch LCD. The secondary LCD/EVF port and an HDMI

®

port cannot be

used at the same time. For more information, go to "LCD/EVF 2 / HDMI Select" on page84.

4 Focus Hook

Mounting

Point

2

Mount the focus hook. Comes with a set screw installed to protect the threaded insert when the

focus hook is not in use.

5 Focus Hook

Storage

Location

2

Store the focus hook or set screw

6 Back Focus

Adjustment

Screw

Adjust back focus

1. The DSMC2 LEMO Adaptor A allows you to mount other RED

®

displays.

2. Install only the focus hook or set screw to this mounting point. Damage to the media bay or other components of the camera system caused by

installing other devices is not covered under warranty.

WEAPON/EPIC-W OPERATION GUIDE

MEDIA BAY CONTROLS

Figure: Media Bay Controls

# CONTROL DESCRIPTION

1 User Key 1 Programmable key

User Key 1 + 2 Press: Eject Media

2 REC button Programmable key

Full Press: Record Toggle

Half Press: AF Start

3 User Key 2 Programmable key

User Key 1 + 2 Press: Eject Media

For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.

WEAPON/EPIC-W OPERATION GUIDE

MEDIA BAY LEDS

Figure: Media Bay LEDS

This section describes the LED functions for the media bay.

# LED COLOR/FLASHING DESCRIPTION

1 Media Status LED (Back of media

bay)

Off No media mounted

Green Preview; media mounted with > 10% of media space

available

Amber Record finalizing or playback mode

Amber flashing

(slow)

Formatting media

Red flashing (slow) Media mounted with > 5% and ≤ 10% of media space

available

Red flashing (fast) Media mounted with ≤ 5% of media space available

Red Recording; media mounted with > 10% of media space

available

2 Record Status LED

1

Off Not recording, or media not mounted

Red Recording

1. For more information on how to enable/disable this LED, go to "Indicator" on page116. If media is not mounted, this LED is off.

WEAPON/EPIC-W OPERATION GUIDE

REDMINI-MAG SYSTEM

Figure: RED MINI-MAG (120GB)

RED MINI-MAG

®

SSDs deliver fast and reliable recording options for your camera. A RED STATION

®

enables you to

connect media to your computer for offloading and editing. RED offers the following RED MINI-MAG SSDs:

Item Part Number Required Firmware

RED MINI-MAG (120GB) 750-0075 v6.1.35 or later

RED MINI-MAG (240GB) 725-0082 v5.1.47 or later

RED MINI-MAG (512GB) V4

1

725-0078 v5.1.34 or later

RED MINI-MAG (512GB) V5

1

725-0078 v6.2.60 or later; or v6.3.17 or later

RED MINI-MAG (512GB) V6

1

725-0078 v6.2.63 or later; or v6.3.27 or later

RED MINI-MAG (1TB)

2

725-0081 v5.3.34 or later

1. To see the Model number, go to Menu > Media > Device.

2. The RED MINI-MAG 1TB can take up to 20 seconds to mount to a computer or a camera.

For more information, see the DSMC Media Operation Guide, available at www.red.com/downloads.

WEAPON/EPIC-W OPERATION GUIDE

EXPANDERS

NOTE: Only one (1) expander module can be used at a time.

RED offers the following DSMC2 expanders:

Item Part Number

DSMC2 Base Expander 720-0033

DSMC2 REDVOLT Expander 720-0040

DSMC2 Jetpack Expander 720-0039

DSMC2 Jetpack-SDI Expander 720-0048

DSMC2 V-Lock I/O Expander 720-0045

DSMC2 BASE EXPANDER

Figure: DSMC2 Base Expander

The DSMC2 Base Expander is an ideal connector module for general input/output (I/O) needs. Manufactured from

lightweight and durable magnesium, this low-profile module mounts directly to the BRAIN and offers interface

connections for power (DC IN), HDMI, 3G-SDI (HD-SDI), CTRL and SYNC ports (for Timecode and Genlock), as well

as a 3.5mm microphone input and a 3.5mm line-level headphone out.

The DSMC2 Base Expander also offers rear-mounting support for DSMC2-compatible battery and power modules,

such as the DSMC2 REDVOLT

®

XL Module. The low profile DSMC2 Base Expander offers a variety of connectors and

is ideal for run-and-gun and independent shooters.

NOTE: Only one (1) expander module can be used at a time.

WEAPON/EPIC-W OPERATION GUIDE

DSMC2 REDVOLT EXPANDER

Figure: DSMC2 REDVOLT Expander

Designed for advanced configurations, the DSMC2 REDVOLT Expander mounts directly to the camera and offers an

expansive array of I/O connectors and functionality available for the camera system. The DSMC2 REDVOLT Expander

features ports for power in (DC IN), Genlock (BNC), Timecode (LEMO), GIG-E, and more. HDMI and two 3G-SDI (HD-

SDI) outputs offer versatility for your video output needs, while an integrated USB power output is available to support

wireless HDMI transmitters.

The DSMC2 REDVOLT Expander offers a removable audio module with two (2) standard XLR connections for most

professional audio needs. Each XLR input features a 3-position selector switch to designate the incoming audio signal

type: Balanced Line Level, Balanced Mic Level, and Balanced Mic with +48V phantom power. Additionally, a 3.5mm

line-level headphone jack lets you sample audio during takes and in playback mode.

The DSMC2 REDVOLT Expander also provides multiple auxiliary power outputs, enabling the use of peripheral camera

accessories and more:

A rear-facing 4-Pin 0B LEMO AUX PWR output supports Start/Stop Trigger IN, Tally OUT, and provides power out

up to 1.5 Amps.

A front-facing 2-Pin 0B LEMO AUX PWR port provides 3.0A maximum.

A front-facing 7-Pin 0B LEMO SERIAL provides 1.5A maximum. The SERIAL port is ideal for connecting to motor

drivers.

A rear-facing Timecode port offers 5V at 200 mA for powering external timecode devices.

A rear-facing USB port offers 5V at 1.5A for powering HDMI transmitters or small mobile devices.

The two (2) 3-Pin XLR audio ports in the audio module each offer +48V phantom power.

For hot-swap support when it matters most, the DSMC2 REDVOLT Expander also supports a single REDVOLT

battery. Additional DSMC2-compatible battery and power modules can be mounted for your changing power needs.

The DSMC2 REDVOLT Expander also features a selector switch that enables the camera to automatically boot when

power is provided via the DC IN connector on the expander. This feature allows you to use a connected DC input

supply to turn the camera on and off when the camera is mounted in remote or difficult to maneuver locations. This

expander is the ideal solution for a variety of production environments, maximizing camera interface and functionality

for the most demanding shoots.

NOTE: Only one (1) expander module can be used at a time.

NOTE: The DSMC2 REDVOLT Expander requires that your camera must be on firmware v6.2.55 or later.

WEAPON/EPIC-W OPERATION GUIDE

Page is loading ...

Red Digital Cinema Epic 6.3 User manual

This manual is also suitable for

Red Digital Cinema Epic 6.3 User manual

Related papers

Other documents