Renkforce RF-3794904 Owner's manual

Brand: Renkforce

Model: RF-3794904

Type: Owner's manual

Page is loading ...

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

may damage the product.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Do not touch the power adapter if there are any signs of damage, as this may

cause a fatal electric shock! Switch off the mains voltage to the socket containing

the power adapter (switch off at the corresponding circuit breaker or remove the

safety fuse, and then switch off at the corresponding RCD protective switch).

You can then unplug the power adapter from the mains socket. Dispose of the

faulty power adapter in an environmentally friendly manner and discontinue use.

Replace it with a power adapter of the same design.

• The mains socket must be located near to the device and be easily accessible.

• Only power the product using the power adapter provided.

• Only connect the power adapter to a standard mains socket connected to the

public grid. Before plugging in the power adapter, check whether the voltage

stated on the power adapter complies with the voltage of your electricity supplier.

• Never connect or disconnect power adapters if your hands are wet.

• Never unplug the power adapter from the mains socket by pulling on the cable;

always use the grips on the plug.

• When setting up the product, make sure that the cables are not pinched, kinked

or damaged by sharp edges.

• Always lay the cables so that nobody can trip over or become entangled in them.

This poses a risk of injury.

• For safety reasons, disconnect the power adapter from the mains socket during

storms.

• Use this power adapter (LED converter) only with this lighting unit.

• Never pour liquids over electrical devices or place objects lled with liquid next to

the device. If liquid or an object gets into the device, power down the respective

mains socket (e.g. switch off the circuit breaker), and then pull the mains plug

from the mains socket. Discontinue use and take the product to a specialist repair

centre.

• Never use the product immediately after it has been brought from a cold room

into a warm one. The condensation generated could destroy the product. The

power adapter may also cause a fatal electric shock! Allow the product to reach

room temperature before connecting it and putting it to use. This may take several

hours.

• Consult a technician if you are not sure how to use or connect the product, or if

you have concerns about safety.

• Maintenance, modications and repairs must only be carried out by a technician

or a specialist repair centre.

• If you have any questions that are not answered in these operating instructions,

please contact our technical customer service or other professionals.

Product overview

Mode I

(Door mode)

Mode II

(Touch mode)

Sensor of the door

mode

Slide your nger in the area to the right of the sensor to turn

the light on or off. It is not necessary to touch the case. The

sensor reacts at a distance of approx. 1 cm and the light turns

on or off.

Mode switch

Cover

Screw

Operating instructions

48.26 cm (19") rack LED lighting unit

Item no. 1897452

Intended use

The LED lighting unit is suitable for installation in a 48.26 cm (19") server rack and delivered

with mounting hardware. The product has 30 bright LEDs, an IR door sensor, and a non-contact

on/off switch. Power is supplied via the power adapter included with the product.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture

(e.g. in a bathroom) must be avoided under all circumstances.

For safety and approval purposes, do not rebuild and/or modify this product. Using the product

for purposes other than those described above may damage the product. In addition, improper

use can cause hazards such as a short circuit, re or electric shock. Read the operating

instructions carefully and store them in a safe place. If you pass the product on to a third party,

please hand over these operating instructions as well.

This product complies with statutory, national and European regulations. All company and

Delivery content

• LED lighting unit

• Power adapter (LED converter)

• Mounting hardware (2x screws, 2x covers, magnetic tape)

• Operating instructions

Up-to-date operating instructions

To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR

code on this page. Follow the instructions on the website.

Explanation of symbols

The symbol with the lightning in a triangle indicates that there is a risk to your health,

e.g. due to an electric shock.

The symbol with an exclamation mark in a triangle is used to highlight important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and tips on how to use the product.

The power adapter is designed in protection class II.

The lighting unit is built according to protection class III.

The product must only be installed and used in dry, indoor locations. The product

must not become damp or wet, otherwise there is a risk of a fatal electrical shock!

Safety instructions

Read the operating instructions carefully and observe in particular the safety

instructions. If you do not follow the safety instructions and information on

proper handling in these operating instructions, we assume no liability for any

resulting personal injury or damage to property. Such cases will invalidate the

warranty/guarantee.

• The product is not a toy. Keep out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. It may become a

dangerous plaything for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Never expose the product to mechanical stress.

• Caution, LED light:

- Do not look directly at the LED light!

- Do not look into the beam directly or with optical instruments!

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capturing in

electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is

prohibited. This publication reects the technical status at the time of printing.

Mounting in a server rack

• The lighting unit can be installed in a 48.26 cm (19 inch) server rack. You can use the supplied

mounting hardware (screws or magnetic tape) to attach the lighting unit.

• If using the magnetic tape, make sure that the mounting surface on the lighting unit is clean

and free of dust, grease and moisture.

• Check that the magnetic tape adheres adequately to the mounting surface inside your server

rack.

Be careful not to cover or glue over the mode switch when attaching the magnetic

tape to the lighting unit.

• Switch the product to the desired mode before installation. There are two available operating

modes: Mode I - (door mode) or mode II (touch mode).

• It is recommended to check the two modes before installation. To do this, connect the round

plug of the power adapter to the socket on the lighting unit and the power adapter to a

suitable mains socket. Please also note the illustration in the section “Product overview”.

Then disconnect the power adapter from the mains socket and the lighting unit.

• Use the touch mode if you want the light to switch on manually by pressing with your nger.

When installing, make sure that the sensor area is easily accessible.

• Use the door mode when the light should turn on when opening the rack door. The detection

range of the door sensor is approx. 4 – 5 cm.

• As soon as an object is located at a distance of approx. 4 – 5 cm in front of the door sensor,

the light switches off. When the object (rack door) is removed from the door sensor, the light

turns on.

• It is recommended to x the door sensor of the lighting unit at a distance of approx. 1 cm to

the closed rack door. As shown in Figure.

1 cm distance

• The screw holes can be covered with the supplied covers after mounting.

• After installation, connect the round plug of the power adapter to the socket on the lighting

unit and the power adapter to a suitable mains socket.

• Check the function of the lighting unit.

Care and Cleaning

• Disconnect the product from the mains socket before cleaning.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the case or cause the product to malfunction.

• Do not immerse the product in water or other liquids.

• Use a dry, lint-free cloth to clean the product.

• The LED bulbs are not interchangeable.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product according to

the relevant statutory regulations.

You thus full your statutory obligations and contribute to environmental protection.

Technical Data

a) Lighting unit

Input voltage/current ..................... 12 V/DC, 0.25 A

Power consumption ...................... 3 W

Bulb .............................................. 30 x SMD3014 LED, not interchangeable

Luminous intensity ........................ 223 lm

Colour temperature ....................... 6500K, cold white

Protection class ............................ III

Operating conditions ..................... -20 to +45 °C, 30 – 60% RH

Storage conditions ........................ -25 to +65 °C, <85% RH

Dimensions (L x W x H) ................ 300 x 28.5 x 9.5 mm

Weight .......................................... approx. 169 g

b) Power adapter (LED converter)

Operating voltage ......................... 100 – 240 V/AC, 50/60 Hz

Output voltage/current .................. 12 V/DC 500 mA

Output power ................................ max. 6 W

Protection class ............................ II

Cable length ................................. 1.5 m

Page is loading ...

Renkforce RF-3794904 Owner's manual

Brand: Renkforce

Model: RF-3794904

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce RF-3794904 Le manuel du propriétaire
Deutsch: Renkforce RF-3794904 Bedienungsanleitung
Nederlands: Renkforce RF-3794904 de handleiding

Renkforce RF-3794904 Owner's manual

Renkforce RF-3794904 Owner's manual

in other languages

Related papers

Other documents