Auto Wash
Start
5 600 053 849 (8301) 635D–bo
en
Brief and handy:
everything your dishwasher
needs.
Before using for the first time,
still read the installation and
operating instructions!
Start programme Off we go
Press ”Start” in the main menu
Switch off the appliance Everything o.k.
When a buzzer has been emitted 5 times
(end of programme), press the main switch .
Fill with rinse aid
Fill with detergent
Select programme
with /-+ in main menu
Fill with salt
Turn on the tap
Switch on the appliance
To switch on, press main switch .
Summary of instructions for dishwasher
Options
Useful information when using the appliance for the first time
Before using the appliance for the first time
– Select the display language, see operating instructions
– Fill with salt and rinse aid, see below
– Adjust softening system, see operating instructions
Main menu:
– Clear text provides information about possible settings, operations
– Arrows identify the buttons which can be pressed
– Buttons enable settings, operations
Operating principle, display with buttons:
StartOptions
Auto Wash
Not required if softening system set to “0”. Required if “Refill salt” is displayed
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Required if “Refill rinse aid” is displayed.
Press the
marking,
Lift the
lid
Pour in
the rinsing
agent
Close the
lid.
CLICK
Little dirt, little cleaning agent
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in the
cleaning agent
Push the lid
too, press.
PLOP
Quick, economical or intensive
The programme data is based on laboratory
measured values in compliance with Euro-
pean standard EN 50242. Deviations are
possible in practice.
Programme overview
Duration in minutes
Power consumption in kWh
Water consumption in litres
Auto
Super
Wash
Auto Wash
Prerinse
only
Auto
Delicate
Wash
Quick
Wash
100-140
1,20-1,60
16-23
100-160
1,00-1,30
12-20
80-110
0,80-1,10
10-17
30
0,60
10
19
0,10
4
Options/standard settings Standard programmes
Select with “Options”, adjust with –/+, save with main menu/“Options”:
1. Timer programming
2. Reduce time
3. Degree of dryness
4. Buzzer volume
5. Water hardness
6. Rinse aid dosage
7. Language
8. Standard programmes
Duration in minutes
Power consumption in kWh
Water consumption in litres
135
0,65
19
Normal
Extra
Normal
Eco
Normal Normal
Plus
150
1,05
14
140
1,05
14
140
1,05
15
Maintenance and care
For perfect rinsing results
Filters
Check and,
if required,
clean:
Rotate filter cylinder,
remove filter system
Rinse under
running water
Insert Screw on filter
system.
NOTE MARK!
Spray arms
Remove blockages/
deposits
Pull up lower arm Unscrew upper arm Clean under running
water (if required, use
a toothpick)
Insert lower arm Screw on upper arm
Troubleshooting
Dealing with problems correctly ...
Fault Possible causes
Wrong language displayed
Appliance does not run/
stops ...
Utensils are
not clean ...
Sand or gritty
residue on the
utensils ...
Language adjusted
No/insufficient water
check whether ...
Utensils close together/on top
of each other ...
Insufficient detergent ...
Unsuitable programme ...
Spray arms blocked ...
Filters loose ...
Filters dirty ...
Spray arm nozzles blocked ...
Insufficient water ...
Switch off the appliance. Switch on
the appliance by holding down the
main switch until the display illumi-
nates. Select the language.
Turn on the water supply.
Supply fittings unobstructed
and not calcified.
Supply hose kink-free.
Arrange utensils according to
instructions.
Comply with manufacturer’s
specifications, select suitable pro-
gramme. Re-arrange obstacles
(e.g. large spoons).
Clean filters (see above),
attach correctly (MARK).
Clean filters (see above).
Clean spray arms (see above).
See “Appliance does not run”.
Remedial action
Programme does not start/does
not continue ...
Residual water in the appliance ...
Programme has not been
started ...
Door is open or was opened
before end of programme ...
If required, start the programme.
Close the door, wait until the
programme ends (buzzer
emitted 5 times).
Fault Possible causes Remedial action
Plastic parts/utensil
parts discoloured ...
Detergent with lower
bleaching effect ...
Insufficient detergent ...
Use detergent with chlorine
bleaching.
Comply with manufacturer’s
specifications.
Milky deposits on
the utensils
(removable) ...
Glasses cloudy/
dull ...
Rust on the cutlery ...
Rinse aid dosage too high
(visible streaking) ...
Rinse aid dosage too low ...
Water too hard ...
Glasses not dishwasher-proof ...
Detergent unsuitable ...
Cutlery not
rust-resistant ...
Reduce or increase dosage
according to instructions.
Refill with salt/adjust
softening system.
User dishwasher-proof glasses.
Use glass-friendly detergents.
Use dishwasher-proof cutlery.
Further information can
be found in the operating
instructions ...
Self-help is worthwhile!
Interrupting the programme ... Terminating the programme ...
Arranging utensils correctly ...
– Open the door.
– To continue the programme, close the door.
– Open the door and press the “Terminate programme” button.
– Close the door and wait until the buzzer is emitted 5 times.
– Restart the programme or switch off the appliance.
Arrange dishwasher-proof utensils (having removed any ash, wax, grease or ink. Coarsely remove
sticky labels, large remnants of jam, milk products or food) according to the operating instructions
and check that the spray arms can rotate freely.
/