Pneumatic Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002jb
SKU: STAND-V002JB
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
A (x1)
Clamp
B (x2)
Arm
C (x2)
Extension
Arm
D (x8)
M4x8
E (x8)
M4x12
F (x8)
M4x30
G (x1)
3mm Allen
Wrench
H (x1)
5mm Allen
Wrench
K (x4)
M6x25
L (x4)
Plastic Cap
I (x8)
Spacer
J (x1)
Cable Clip
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Adjust clamp (A) to fit desktop. Make sure pole is
secured in base by twisting clockwise, then use
3mm allen wrench (G) to tighten grub screw in
back of base.
STEP 2
Secure clamp to desktop using clamp screw. NOTE: If desktop is too thick, use 5mm allen wrench (H)
to remove clamp screw and two screws holding clamp base together. Rotate clamp base upside down
and reassemble as shown in diagram.
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
S=5mm
4
STEP 3
Adjust the locating ring to desired height and tighten to support the arms. Adjust the aluminum
support bracket to rest on the locating ring and secure using handle and the 3mm allen wrench (G).
STEP 4
Place the extension arms (C) onto the aluminum support bracket and secure each one using bolts (K)
and plastic cap (L). Tighten using a phillips head screwdriver.
S=3mm
5
STEP 5
OPTION A: Flat Back Monitor
Attach VESA plate of arm (B) to back of monitor using four screws (D, E) as shown in diagram.
OPTION B: Curved Back Monitor
For recessed monitors, spacers (I) and screws (F) may be required.
6
STEP 6
STEP 7
Attach arms (B) to extension arms (C) using bolts (K) and plastic cap (L) using a phillips head
screwdriver as shown in diagram.
Use the 5mm allen wrench (H) to adjust the spring tension inside the arms (B) as shown in diagram,
depending on the weight of your monitors.
S=5mm
7
STEP 8
Use the 3mm allen wrench (G) to adjust tension in arms, and the 5mm
allen wrench (H) to adjust tension in monitor brackets.
STEP 9
Insert monitor cables into cable covers on underside of arms (B). Leave enough slack to allow full
adjustment and motion of arms. Use the cable clip (J) to attach cables to pole.
S=3mm
S=3mm
S=5mm
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/