Ignis ADP 7452 A+ 6S WH Owner's manual

ADP 7452 A+ 6S WH
Ignis
Brand
Ignis
Model
ADP 7452 A+ 6S WH
Type
Owner's manual
Montageanweisung - Stand-Modell
Technische Änderungen vorbehalten
Assembly instructions - Free-standing model
We reserve the right to make technical modifications
Instructions de montage - Pour le modèle à installation libre
Sous réserve de modifications techniques
Montage-instructies - Vrijstaand model
Technische wijzigingen voorbehouden
Instrucciones para el montaje - Modelo de libre colocación
Reservado el derecho de introducir modificaciones técnicas
Instruções para a montagem - Modelo com instalação livre
Com reserva de eventuais alterações técnicas
Istruzioni per il montaggio - Modello a libera installazione
Con riserva di modifiche tecniche
δηγς για τ µντρισµα - Μντλ λθρης γκατστασης
Μ την πιλαη για τνικς αλλαγς
Monteringsanvisning - Modell för fri installation
Vi förbehåller oss rätten att göra tekniska ändringar
Monteringsanvisning - Frittstående modell
Vi forbeholder oss retten til å foreta tekniske endringer
Monteringsvejledning - Fritstående model
Vi forbeholder os retten til at foretage tekniske ændringer
Asennusohjeet - Vapaasti seisova malli
Oikeus teknisiin muutoksiin pidätetään
Instrukcja montażu - Model wolnostojący
Z zastrzeżeniem zmian technicznych
Pokyny k montáži - Model k volné instalaci
S výhradou technických změn
Montážne pokyny - Voľne stojaci model
Technické úpravy vyhradené
Szerelési utasítások - Tetszőleges módon üzembe helyezhető típus
A műszaki módosítások jogának fenntartásával
Укaзaния пo мoнтaжу - Cвoбoднo стoящaя мoдeль
Фирмa oстaвляeт зa сoбoй прaвo внoсить в прибoр тeхничeскиe измeнeния
Инструкции зa мoнтaж - Мoдeл зa свoбoднo пoстaвянe
Cъс зaпaзeнo прaвo зa тeхничeски мoдификaции
Instruc∑iuni de montare - Model cu instalare liber™
Cu rezerva de a putea aduce modific™ri de natur™ tehnic™
Kurulum Talimatları - Serbest kurulum modeli
Teknik de¤ifliklik yapma hakkımız saklıdır
00192 10-01-2006 15:04 Pagina 1
D
Hinweise Seite 3
Montageanleitung Seite 29
GB Precautions Page 4
Assembly instruction Page 29
F Avertissements Page 6
Instructions de montage Page 29
NL Waarschuwingen Pagina 7
Montage-instructies Pagina 29
E Advertencias Página 8
Instrucciones de montaje Página 29
P Advertências Página 9
Instruções para a montagem Página 29
I Avvertenze Pagina 10
Istruzioni di montaggio Pagina 29
GR Προειδοποιήσεις Σελίδα 11
Οδηγίες τοποθέτησης Σελίδα 29
S Varningar Sidan 12
Monteringsanvisningar Sidan 29
N Advarsler Side 13
Monteringsanvisning Side 29
DK Advarsler Side 14
Monteringsvejledning Side 29
FIN Varoituksia Sivu 15
Asennusohjeet Sivu 29
PL Ostrzeżenia Strona 16
Instrukcja montażu Strona 29
CZ Upozornění Strana 17
Návod k instalacji Strana 29
SK Upozornenia Strana 18
Pokyny na montáž Strana 29
H Figyelmeztetés Oldal 19
Szerelési utasítások Oldal 29
RUS Предупреждение Страница 20
Указания по монтажу Страница 29
BG Бележки Страница 21
Инструкции за монтаж Страница 29
RO Măsuri de precauţie Pagina 22
Instrucţiuni de montare Pagina 29
HR Upozorenja Stranica 23
Upute za sastavljanje Stranica 29
TR Uyarılar Sayfa 24
Montaj talimatları Sayfa 29
Arabic ﺔﺤﻔﺻ تاﺮﻳﺬﺤﺘﻟا 25
ﺔﺤﻔﺻ ﺐﻴآﺮﺘﻟا تﺎﻤﻴﻠﻌﺗ 29
Hebrew תורהזא דומע 26
הנקתה תוארוה-דומע 29
KO 안전 주의사항 페이지 27
조립 주의사항 페이지 29
Page is loading ...
1. Water connection
- Connection to the mains water supply must be carried out by a qualified technician in compliance
with the manufacturer's instructions and applicable local safety regulations.
- All local water board regulations must be complied with. Water supply pressure: 0.03 - 1.0 MPa.
- The inlet hose must be securely clamped to the water tap to prevent leaks.
- The inlet water temperature varies according to the model installed. Inlet hose marked: "25°C Max":
up to a maximum of 25°C. Other models: up to a maximum of 60°C.
- Depending on the appliance model, the solenoid valve of the inlet hose will be activated by the
mains voltage (see ** assembly instructions).
- Make sure the inlet and drain hoses are kink-free and are not crushed.
- Fix the drain hose to the siphon with a clamp to prevent it from coming off during operation.
- When installing the appliance, make sure water can drain freely (remove the siphon plug if
necessary).
- Do not use old or damaged hoses. Use only the hoses provided or new ones, which can be
requested from the After-Sales Service.
- If hoses are not long enough, contact your local dealer.
- Do not cut hoses and, in the case of appliances fitted with a waterstop system, do not immerse
the plastic casing containing the inlet hose in water.
- Before using the appliance for the first time, check the water inlet and drain hose for leaks.
2. Electrical Connection
- All local electricity board regulations must be complied with.
- Voltage information is shown on the rating plate mounted inside the door on the right hand side.
- The appliance must be earthed as prescribed by law.
- Do not use extension leads or multiple adapters.
- If the power cable is damaged, replace it with an identical one. The power cable must only be
replaced by a qualified technician.
- After appliance installation, the mains plug must be easily accessible so that the appliance can be
unplugged if necessary at any time.
For Austria:
If a fault current switch is fitted upline of the appliance, this must be pulse current-sensitive.
3. Assembly instruction
- During assembly the appliance must be unplugged from the mains.
- Set any electrical screwdrivers to a low torque.
- Attention: when transporting and assembling the appliance, always wear gloves to protect
fingers / hands from sharp edges and corners.
- Be careful with uneven installation surfaces: regulate the foot height.
- For dishwashers with decor panel, fit the decor panel before the rounded plinth.
- The decor panel, if not supplied, is available from After-Sales Service.
- Removing the rounded plinth (see page 34), fitting (see page 35).
4. General indications
- The appliance must only be used in the household and according its purpose.
- Do not use the dishwasher until it has been fully assembled.
- Do not use the dishwasher if it has been damaged in transit. Contact After-Sales Service or your
local dealer.
- Before carrying out any cleaning or maintenance operations, unplug the appliance and turn off the
water tap. The same applies in the event of a malfunction.
- Do not use abrasive products or alcohol on the control panels.
- All sizes in this installation instruction are given in millimetres.
- Packaging varies according to the dishwasher model.
4
GB
5
5
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an A.S.T.A.
approved fuse to BS 1362 type and proceed as follows:
1.
Remove the fuse cover (
A
) and fuse (
B
).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse
cover is lost the plug must not be used until a correct replacement is
fitted.
Correct replacement are identified by the colour insert or the colour
embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact
Whirlpool Service for further instruction. Please do not attempt to
change plug yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the manufactures
instructions and current standard safety regulations.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
04/2010
5019 102 00482/B
D GB F NL E P I GR S N DK FIN PL CZ SK H RUS BG RO HR TR KO
Printed in Poland
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Ignis ADP 7452 A+ 6S WH Owner's manual

ADP 7452 A+ 6S WH
Ignis
Brand
Ignis
Model
ADP 7452 A+ 6S WH
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents