Page is loading ...
Stickers
• Please apply all stickers on individual parts before assembly unless otherwise specified
• DO NOT apply stickers to tires, steering wheel, or spoiler until AFTER
the toddler bed is fully assembled
• For best results, place individual parts on a flat surface before applying stickers.
A12 B12
3
1 Right Side Panel
A
A1
A8
A9
A9
A10
A10
A11
A11
A12
A2 A3 A4 A5
A6
A7CC
Align A10 sticker to A9 along dotted line
Overlap Overlap
Align A11 sticker to A10 along dotted line
Dotted line located here
A10
Dotted line located here
A9
Step 1: Apply A9
Step 2: Apply A10
Step 3: Apply A11
4
2 Left Side Panel
B
B1
B8
B9B10B11
B9
B12
B2B3B4B5
B6
B7 C
A10
Align B10 sticker to B9 along dotted line
Dotted line located here
B10
Dotted line located here
B9
OverlapOverlap
B10
B11
C
Align B11 sticker to B10 along dotted line
Step 1: Apply B9
Step 2: Apply B10
Step 3: Apply B11
5
• Apply D2 sticker beginning here.
•Match cut-out in
headlight sticker to
holes on front bumper
K
3A 3B
4
6
5
D1
E1
E2
E3 E4
D2
D
D
Overlap
N
6
1C
• APPLY STICKERS
C
M
1B1A
A
C
4 x 3/4”
7
2C
• APPLY STICKERS
C
M
2B
2
B
C
4 x 3/4”
8
33A
4A 4B
D
4 x 3/4”
• Turn both side panels and front bumper
upside down to begin assembly
• Turn bed over
• If assembling twin bed ONLY, skip to step 10
A
B
• Fold cover upwards into fully locked position
9
I J K
L
G
• APPLY STICKERS
Follow steps 5A through 9 for toddler bed
5A
6A
5B
6B
E
G
F
6C
1 x 1.0” DIA.
1 x 1/2”
2 x 3/4”
10
7A
7C 7D
7B
E
2 x 3/4”
2 x 1/2” DIA.
• Align center wall with groove on left and right side
panels. Slide down into a fully locked position.
• Fold flap downward towards side panels
• Screw down flap onto side panels
11
J
9
8
11
H
I
2 x 1.0”
BACK VIEW
• If only assembling twin bed, skip to 17A
1
1
2
10
1. Insert back panel latch hooks
into both left/right side panel grooves
2. Slide downward into a fully
locked position
• Optional mattress support board assembly
Dimensions: 53.65”(L) x 30.5”(W) x 0.50” THICK
12
K
12
L
M
14
15
• Push windshield downward into groove on right
side panel into a fully locked position.
• Align hood tabs with holes
on left and right side panels.
Push into a fully locked
position.
13
12A
4 x 3/4”
13
N
16
17B
O
17A
2 x 1.0” DIA.
2 x 3/4”
14
• APPLY “N” STICKER AFTER SPOILER
IS FULLY ASSEMBLED
• APPLY “O” STICKER AFTER SPOILER IS
FULLY ASSEMBLED
N
Dotted line located here
O
17C
17D
O
Align O sticker on N along dotted line
Overlap
2.50” (approx.) Apply sticker here
N
O
15
B13 A13
Twin Conversion
• Please keep and store all loose screws in a
safe place when converting toddler bed to twin bed.
All loose screws will be used to assemble the toy box.
6 x 3/4”
2 x 1/2” DIA.
3
2
• To remove windshield,
pull upward on right side
while pushing side
panel outward to unlock.
1
• Lift off center hood
• Unscrew left and right hood panels
17
13
4
• Remove mattress and left/right mattress frames
5
Twin Bed
• Works with standard boxspring and twin mattress
18
3
4
• APPLY STICKERS
• APPLY STICKERS
R
S
P
Q
2
1
F3 F4H
R
P
Q
Toy Box
2 x 1.0”
G
19
56
7
2 x 1.0”
2 x 3/4”
• Align center wall with grooves on left and right side
panels of toy box. Slide down into a fully locked position.
2 x 1/2” DIA.
• Fold flap downward towards side panels.
• Screw down flap
onto side panels
20
/
