JETER JA6F Operating instructions

Brand: JETER

Model: JA6F

Type: Operating instructions

This manual is also suitable for

JC6F

JETER JA6F

Below you will find brief product information for JETER JA6F.

The JETER JA6F is a 7” Portable Bandsaw with a powerful 420W motor, providing efficient and precise cutting. It features a chain vise for secure clamping of materials and an angle vise for angled cuts up to 45 degrees. The saw has a sturdy frame and a carrying hook for easy transportation.

Capabilities:

Cuts a wide range of materials, including metal, wood, and plastic
Adjustable load settings for different cutting materials
Blade guide bracket adjustment for optimal cutting precision
Automatic power shut-off for safety

JETER JA6F

Below you will find brief product information for JETER JA6F.

Capabilities:

Cuts a wide range of materials, including metal, wood, and plastic
Adjustable load settings for different cutting materials
Blade guide bracket adjustment for optimal cutting precision
Automatic power shut-off for safety

50/60Hz

1051209 V1

JC6F

JA6F

7” Portable Bandsaw

JETER

Angle Vise

JA6F

Chain Vise

JC6F

Operations Manual

Exceeding the Extreme

www. JET ERt o o ls . com

7” PIPE Cutting Expert

CATALOG

Page

☉General Safety Rules 。。。。。。。。- 1 -

☉Characteristics 。。。。。。。。。。。- 2 -

●Parts Description

●Specifications

☉Operation Rules

①Before Operation 。。。。。。。。。- 3 -

②Before Cutting 。。。。。。。。。。- 3 -

●Blade Installation 。。。。。。。 - 3 -

●Load Adjustment。。。。。。。。 - 4 -

●Blade Guide Bracket Adjustment 。。 - 5 -

●Clamping And Angle Setting。。。。 - 5 -

(1)Angle Vise Adjustment

(2)Chain Vise Adjustment

③Cutting Rules。。。。。。。。。。 - 6 -

④Maintenance。。。。。。。。。。 - 6 -

☉Part List & Explosion Drawings。。。 - 7 -

☉Electrical Schematic。。。。。。。 - 11 -

Operations Manual

☉General Safety Rules

WARNING

1. Read and understand instructions of this manual entirely before operating the machine.

2. Always wear approved safely glasses /face shields when using the machine.

3. Make certain the machine is properly grounded.

4. Before machine in operation, remove tie, ring, watch, other jewelry, and roll your sleeves up

to above elbows. Remove loose clothing and confine long hair.

5. Keep the floor around this machine clean and free of scrap material, oil and grease.

6. Keep machine guards in place at all times when the machine is in use. If it removed for

maintenance purpose, pay extra attention and replace these guards at once.

7. Do not over reach. Keep a balanced stance all the time so that you don’t fall lean against

blade or some other moving parts.

8. Whenever make any adjustments or maintenance with the machine must unplugged the

power source.

9. Use the right tool. Don’t force a tool or attachment to do a job that it was not designed for.

10. Replace warning labels if they have become obscured or removed.

11. Make certain the motor switch is in “off” position while connecting the machine into the

power supply.

12. Pay your work undivided attention. Looking around, and carrying on a conversation, or

“Horse-play” are careless acts which might result in serious injury.

13. Keep visitors a safe distance from the work area.

14. Use recommended accessories, and parts. Improved accessories may be hazardous.

15. From the good habit of checking, to see keys and wrenches are removed before turning

on this machine.

16. Always keep hands & fingers away from the black when this machine is running.

17. Never hold a material with this saw in the horizontal position. Please be sure always use

the vise to clamp it securely.

18. Read and understand warnings that posted on the machine.

19. Always provide necessary support for long and heavy material.

20. Use a sharp blade and always keep machine clean for a best and safest performance.

21. Failure to comply with any of these warnings may cause serious injury.

Operations Manual

☉Characteristics

●Parts Description

Chain Vise

Frame Cover

Head Handle

Cover Locker

Wire Stick

Base Handle

Wheels

Overload

Chain Handle

Base(Chain Type)

Half Nut

Chain Hooker

Switch

Handle Wheel

Base(Vise Type)

Half Nut Handle

Fixed Vise

Movable Vise

Tension Handle

Bearings

Rear Blade Guide

Bracket

Blade

Carrying Chain

Carrying Hook

Front Blade Guide

Bracket

Saw Head

Load Switch

Angle Rod

Motor

Locking Handle

Angle Vise

Operations Manual

●Specifications

TYPE

CHAIN VISE

ANGLE VISE

CAPACITY

。

Ø180 □150

。

Ø80 □80

BLADE SIZE

13X0.65X1642(mm)

BLADE SPEED

40MPM(50HZ)，48MPM(60HZ)

MOTOR

420W(50/60HZ)

PACKING SIZE

1030*500*470*mm(L x W x H)

N.W./G.W.

39KG/43KG

44KG/47KG

☉Operation Rules

①Before Operation

Transportation：Please make sure the carrying chain is fixed on

the carrying hook. Then lift head handle to move with wheels by

one person. The other way, one can lift the head handle, and the

other one can lift the base handle to transport machine.

②Before Cutting

●Blade Installation：make sure the power is off and turn the cover

locker to release the cover.

(1)Remove blade

1.Turn the tension handle to “RELEASE”

direction to loosen blade.

2.Take blade off from bearings.

3. Take blade off from guide bracket.

4. Take blade off from wheels .

(2)Install blade

Install blade by the contrary way of

“remove blade ”.

①

②

③

④

Operations Manual

●Load Adjustment：

There are four load states to choose depend on what material you cut.

(because of the cutting situations are complex, so you can choose the

load state best suit for you or control the load by head handle with

hand)

(1)Extra light

(2)Light

(3)Normal

(4)Heavy duty

Steps： 1.Lift saw head to upper state.

2.Push load wheel and turn to move pin to the load state you

want.

<<Load/Saw Blade Chart>>

Operations Manual

●Blade Guide Bracket Adjustment：

For the best cutting precision, rear

blade guide bracket can move

forward or backward to fit cutting

size.

Don’t let bracket touch cutting material to damage or

affect cutting precision .

Don’t adjust during operation.

●Clamping And Angle Setting：

(1) Angle Vise Adjustment：

1. Clamp material

Place material on the fixed vise side, then lift half nut handle to clamp

and screw the wheel.

Operations Manual

2.Angle adjustment

you can have 0~45

。

range to choose ,

then loose two 17mm bolt with tools

and move to

the right angle, then screw two bolts to

fixed the angle.

(2) Chain Vise Adjustment：

(i) Turn handle wheel to left rotation to release

chains.

(ii) Put material on the ”V groove” and put

chains on it .

(iii) Turn handle wheel to right rotation to clamp

material.

Cutting Rules

(i) Lift the saw head, then turn on for a while.

(ii) Put sawblade on material gently and start cutting procedure.

(iii) When cutting is over, the power will automatically shut

down.

④ Maintenance:

◆After cutting procedure, it’s necessary to clean the dust to avoid dust

damaging machine parts.

◆After operation, please plug out and hook on the carrying hook .

Then put machine in dry place to avoid rust.

Operations Manual

☉

Part List & Explosion Drawings

Operations Manual

FOR

JC6

F/JA6F

☉

Electrical Schematic

JETER JA6F Operating instructions

Brand: JETER

Model: JA6F

Type: Operating instructions

This manual is also suitable for

JC6F

JETER JA6F

Below you will find brief product information for JETER JA6F.

Capabilities:

Cuts a wide range of materials, including metal, wood, and plastic
Adjustable load settings for different cutting materials
Blade guide bracket adjustment for optimal cutting precision
Automatic power shut-off for safety

Download PDF

report

in other languages

日本語: JETER JA6F 取扱説明書

JETER JA6F Operating instructions

This manual is also suitable for

JETER JA6F Operating instructions

in other languages

Other documents