Indesit DSIE 2B10 UK N Daily Reference Guide

Brand: Indesit

Model: DSIE 2B10 UK N

Category: Dishwashers

Type: Daily Reference Guide

Indesit DSIE 2B10 UK N dishwasher offers efficient dish cleaning with its 5 programs, including Eco, Intensive, Mixed, Rapid 40’, and Half Load. It features adjustable upper rack height, foldable flaps for wine glasses, and a cutlery basket for safe utensil placement. With its user-friendly control panel and indicator lights, you can easily select programs and monitor the progress of your dishes.

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

THANK YOU FOR BUYING A INDESIT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions

and the

User Manual, by visiting our website

docs.indesit.eu

and following the Instructions

on the back of this booklet.

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

1. ON-OFF / Reset button with indicator light

2. Program selection button

3. Program indicator lights

4. START/Pause button with indicator light

DAILY REFERENCE

GUIDE

CONTROL PANEL

PRODUCT DESCRIPTION

1 2 3 4

0000 000 00000

Service:

1011

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes

and on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see Product Description) and must be lled when the green oat on the

cap of the salt reservoir is no longer visible..

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the wa-

ter softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in your

house. This information can be obtained from your local water supplier.

The factory sets the default value for the water hardness

• Switch on the appliance by pressing the ON/OFF button.

• Switch o the appliance by pressing the ON/OFF button.

• Hold down button P for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing the ON/OFF button.

• The program indicator light of the current set level ashes.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch o the appliance by pressing the ON/OFF button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher deter-

gent.

Water Hardness Table

Level

°dH

German

degrees

°fH

French

degrees

Liters

Softening capacity

(depending of the set

hardness Level)

1 Soft 0 - 6 0 - 10 150

2 Medium 7 - 11 11 - 20 100

3 Average 12 - 16 21 - 30 50

4 Hard 17 - 34 31 - 60 30

5 Very hard 35 - 50 61 - 90 16

Example: Level 3 is set as default, what means regeneration of the softener should take

place once per 50 ltr.

More on SOFTENER REGENERATION (how often it occures, the uses of water,

energy, etc.) you can nd on the page CARE AND MAINTENANCE.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be lled when when the dark optical indicator on the dispenser door C

becomes transparent.

1. Open the dispenser B by pressing and pulling up the tab on the lid.

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

f you are not completely satised with the drying results, you can adjus

the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it o using the ON/OFF button.

• Press button P three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The program indicator light of the current set level ashes.

• Press button P to select the level of rinse aid quantity to be supplied.

• Switch it o using the ON/OFF button

Setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specic to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set a mid-

-range number (4-5 ).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device D.

Introduce the detergent into the dry dispenser E only. Place

the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser E there are

indications to help the detergent

dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until

the closing device is secured in pla-

ce.

The detergent dispenser automatically opens up at the right time

according to the program.

Usage of detergent not designed for dishwashers may cause mal-

function or damage to the appliance.

Water Hardness Table

Level

°dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Values given for programmes other than the eco programme are indicative only. The actual time may vary depending on many factors such as tem-

perature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected

options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Program

Drying

phase

Duration

of wash

program

(h:min)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

1. Eco 50°

4:00 11.5 0.84

2. Intensive 65° 2:30 15.0 1.5

3. Mixed 55° 2:25 15.0 1.35

4. Rapid 40’

50°

0:40 8.0 0.9

5. Half Load 50°

1:15 11.0 0.9

PROGRAMS TABLE

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1 ECO

Eco program is suitable to clean normally soiled tableware, that for this

use, it is the most ecient program in terms of its combined energy

and water consumption, and that it is used to assess compliance with

the EU Ecodesign legislation.

2 INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

3 MIXED

Mixed soil. For normally soiled dishes with dried food residues.

4 RAPID 40’

Program to be used for half load of lightly-soiled dishes with no dried

food residues. Does not have drying phase.

5 HALF LOAD

Ideal for washing a half load of lightly or normally soiled crockery.

Notes:

Please note that cycle Rapid 40’ is dedicated for lightly soiled dishes.

LOADING THE RACKS

LOWER RACK

For pots, lids, plates, salad bowls, cutlery

etc... Large plates and lids should ideally be

placed at the sides to avoid interferences

with the spray arm.

(loading example for the lower rack)

CUTLERY BASKET

It is tted with top grids for improved cutlery arrangement.

It must only be positioned at the front of the lower rack.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards or they

must be positioned horizontally in the tip-up compartments on

the upper rack.

UPPER RACK

Load delicate and light dishes: glasses, cups,

saucers, low salad bowls.

(loading example for the upper rack)

ADJUSTING THE HEIGHT OF THE UPPER RACK

The height of the upper basket can be

adjusted: high position to place bulky crockery

in the lower basket and low position to make

the most of the tip-up compartments by

creating more space upwards.

The upper rack is equipped with a Upper Rack

height adjuster (see gure), without pressing

the levers, lift it up by simply holding the rack

sides, as soon as the rack is stable in its upper

position. To restore to the lower position, press

the levers (A) at the sides of the rack and move the basket downwards.

We strongly recommend that you do not adjust the height

of the rack when it is loaded.

NEVER raise or lower the basket on one side only.

FOLDABLE FLAPS WITH ADJUSTABLE POSITION

The side foldable aps can be fold or unfold

to optimize the arrangement of crockery

inside the rack.

Wine glasses can be placed safely

in the foldable aps by inserting the stem

of each glass into the corresponding slots.

Depending on the model:

– to unfold the aps there is needed to slide

it up and rotate or release it from the snaps

and pull it down.

– to fold the aps there is needed to rotate

it and slide aps down or pull it up

and attach aps to the snaps.

DAILY USE

1. CHECK WATER CONNECTION

Check that the dishwasher is connected to the water supply

and that the tap is open.

2. SWITCH ON THE DISHWASHER

Open the door and press the ON/OFF button.

3. LOAD THE RACKS (see LOADING THE RACKS)

4. FILLING THE DETERGENT DISPENSER

5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE

Select the most appropriate program in accordance with the type

of crockery and its soiling level (see PROGRAMS DESCRIPTION) by

pressing the P button.

6. START

Start the wash cycle by pressing START/Pause button (led is

lit) and closing the door within 4 sec. When the program starts

you hear a single beep. If the door was not closed within 4sec.,

the alarm sound will be played. In this case, open the door, press

START/Pause button and close the door again within 4 sec.

7. END OF WASH CYCLE

The end of the wash cycle is indicated by beeps and by the ash-

ing

of the indicator light of the selected program. Open the door

and switch o the appliance by pressing the ON/OFF button.

Wait for a few minutes before removing the crockery - to avoid

burns. Unload the racks, beginning with the lower one.

The machine will switch o automatically during certain extended

periods of inactivity, in order to minimise electricity consumption.

If the crockery is only lightly soiled or if it has been rinsed with

water before being placed in the dishwasher, reduce the amount

of detergent used accordingly.

MODIFYING A RUNNING PROGRAM

If a wrong program was selected, it is possible to change it, provided

that it has only just begun: open the door, press and hold the ON/OFF

button, the machine will switch o.

Switch the machine back on using the ON/OFF button and select

the new wash cycle and any desired options; Start the wash cycle by

pressing START/Pause button and closing the door within 4 sec.

ADDING EXTRA CROCKERY

Without switching o the machine, open the door (START/Pause led

starts blinking) (be ware of HOT steam!) and place the crockery inside

the dishwasher. Press the START/Pause button and close the door

within

4 sec., the cycle will resume from the point at which it was

interrupted.

ACCIDENTAL INTERRUPTIONS

If the door is opened during the wash cycle, or if there is a power cut,

the cycle stops. Press the START/Pause button and close the door

within

4 sec., the cycle will resume from the point at which it was

interrupted.

ADVICE AND TIPS

TIPS

Before loading the baskets, remove all food residues from the crockery

and empty the glasses. You do not need to rinse beforehand under

running water.

Arrange the crockery so that it is held in place rmly and does not tip

over; and arrange the containers with the openings facing downwards

and the concave/convex parts placed obliquely, thus allowing the wa-

ter to reach every surface and ow freely.

Warning: lids, handles, trays and frying pans do not prevent the spray-

er arms from rotating.

Place any small items in the cutlery basket.

Very soiled dishes and pans should be placed in the lower basket

because in this sector the water sprays are stronger and allow a higher

washing performance.

After loading the appliance, make sure that the sprayer arms can

rotate freely.

UNSUITABLE CROCKERY

• Wooden crockery and cutlery.

• Delicate decorated glasses, artistic handicraft and antique crockery.

Their decorations are not resistant.

• Parts in synthetic material which do not withstand high temperatures.

• Copper and tin crockery.

• Crockery soiled with ash, wax, lubricating grease or ink.

The colours of glass decorations and aluminium/silver pieces can

change and fade during the washing process. Some types of glass (e.g.

crystal objects) can become opaque after a number of wash cycles

too.

DAMAGE TO GLASS AND CROCKERY

• Only use glasses and porcelain guaranteed by the manufacturer

as dishwasher safe.

• Use a delicate detergent suitable for crockery

• Collect glasses and cutlery from the dishwasher as soon as the wash

cycle is over.

TIPS ON ENERGY SAVING

• When the household dishwasher is used according to the manufac-

turer’s instructions, washing tableware in a dishwasher usually

consumes less energy and water than hand dishwashing.

• In order to maximize dishwasher eciency it is recommended to in-

itiate the wash cycle once dishwasher is fully loaded. Loading

the household dishwasher up to the capacity indicated by the man-

ufacturer will contribute to energy and water savings. Information

on correct loading of tableware can be found in Loading chapter.

In case of partial loading it is recommended to use dedicated wash

options if available (Half load/ Zone Wash, Multizone), illing up only

selected racks. Incorrect loading or overloading the dishwasher may

increase resources usage (such as water, energy and time, as well

as increase noise level), reducing cleaning and drying performance.

• Manual pre-rinsing of tableware items leads to increased water

and energy consumption and is not recommended.

HYGIENE

To avoid odour and sediment which can be accumulated in the dish-

washer please run a high temperature program at least one

a month. Use a tea spoon of detergent and run it without the loading

to clean your appliance.

CARE AND MAINTENANCE

CLEANING THE FILTER ASSEMBLY

Regularly clean the lter assembly so that the lters do not clog and that

the waste water ows away correctly.

Using dishwasher with clogged lters or foreign objects inside ltra-

tion system or sprayarms may cause unit malfunction resulting in lose

of performance, noisy work or higher resources usage.

The lter assembly consists of three lters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without lters or if the lter is

loose.

At least once per month or after each 30 cycles, check the lter assembly

and if necessary clean it thoroughly under running water, using a non-

-metallic brush and following the instructions below:

1. Turn the cylindrical lter A in an anti-clockwise direction and pull

it out (Fig 1).

2. Remove the cup lter B by exerting a slight pressure on the side

aps (Fig 2).

3. Slide out the stainless-steel plate lter C (Fig 3).

4. In case you nd foreign objects (such as broken glass, porcelain,

bones, fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE

the wash-cycle pump protection (black detail) (Fig 4).

After cleaning the lters, re-place the lter assembly and x it in

position correctly; this is essential for maintaining the ecient

operation of the dishwasher.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free

of impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked and da-

mage the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may become encrusted onto the spray arms

and block the holes used to spray the water. It is therefore recommen-

ded that you check the arms from time to time and clean them with

a small non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in an

anti-clockwise direction. The upper spray arm should be replaced so

that the side with the greater number of holes is facing upwards.

The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently

preventing scale buildup on heater, contributing also to better cleaning

eciency.

This system regenerates itself with salt, therefore it is required

to rell salt container when empty.

Frequency of regeneration depends on water hardness level setting

- regeneration takes place once per 5 Eco cycles with water hardness

level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase,

before cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.

The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.

TROUBLESHOOTING

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The dishwasher

won’t start

or does not

respond to com-

mands.

The appliance has not been plugged

in properly.

Insert the plug into the socket.

Power outage.

For safety reasons, dishwasher will not re-start automatically when power returns.

Open dishwasher door, press START/Pause button and close the door within

4 seconds.

The dishwasher door is not closed. Vigorously push the door until you hear the “click”.

Cycle is interupted by door opening

for more than 4 seconds.

Press START/Pause and close the door within 4 seconds.

It does not respond to commands.

Switch o the appliance by pressing the ON/OFF button, switch it back on

after approximately one minute and restart the program. If problem persists,

unplug the appliance for 1 minute, then plug it back in.

The dishwasher

won’t drain.

The wash cycle has not nished yet. Wait until the wash cycle nishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The lter is clogged up with food residues. Clean the lter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes

excessive noise.

The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable

for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart

the current cycle by switching OFF the dishwasher, then switch it on again,

select a new program, press START/Pause and close the door within 4

seconds. Please do not add any detergent.

The dishes are

not clean.

The crockery has not been arranged

properly.

Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely, being

hindered by the dishes.

Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for use

in dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment has

not been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

The dishwasher

does not ll

the water.

All LEDs are

blinking rapidly

No water in the water supply or the tap is

closed.

Make sure there is water in the water supply or the tap running.

The inlet hose is bent.

Make sure the inlet hose is not bent (see INSTALLATION) reprogram

the dishwasher and reboot.

The sieve in the water inlet hose is clogged;

it is necessary to clean it

After having carried out the verication and cleaning, turn o and turn on

the dishwasher and restart a new program.

Dishwasher

nishes the cycle

prematurely.

Drain hose positioned too low or siphoning

into home sewage system.

Check if end of drain hose is placed at correct height (see INSTALLATION).

Check for siphoning into home sewage system, install air admittance valve

if necessary.

Air in water supply. Check water supply for leaks or other issues letting air inside.

Policy and standard documentation and additional product information can be found by:

• Visiting our website docs.indesit.eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).

When contacting our After-sales Service, please state the codes provided on your product‘s

identication plate.

The model information can be retrieved using the QR-Code reported in the energy label.

The label also includes the model identier that can be used to consult the portal of the registry

at https://eprel.ec.europa.eu (available only on certain models).

IEC 436

400011498068

09/2020 ks - Xerox Fabr

iano

Indesit DSIE 2B10 UK N Daily Reference Guide

Brand: Indesit

Model: DSIE 2B10 UK N

Category: Dishwashers

Type: Daily Reference Guide

Download PDF

report

Indesit DSIE 2B10 UK N Daily Reference Guide

Indesit DSIE 2B10 UK N Daily Reference Guide

Related papers

Other documents