Audiovox Pursuit PRO 9445FT Owner's manual

Model PRO 9445FT

Owner's Manual

Remote Keyless Entry

Congratulations on your purchase of this state-of-the-art automotive

convenience system. To fully appreciate the many functions incorporated in

this system, please take a few moments to read this manual.

FEATURES ANDAVAILABLE OPTIONS:

 User Programmable Transmitters Offer Over 16 Million Different

Codes

 Instant Locking and Unlocking of the doors via a Remote Keychain

Transmitter

 Vehicle's Starter is disabled whenever the doors are locked using the

Transmitter

 Programmable Active or Passive Starter Interrupt Operation

 Programmable Auto Lock / Unlock via ignition key

 Optional interior illumination when the doors are unlocked using the

Transmitter

 TheOption Button on the Keychain Transmitter can be used to activate

any of the following optional devices;

* Trunk Release relay

* Remote Car Starter

* Window up or down module

* Garage Door Interface

A  MARK WILL APPEAR IN THE BOX TO THE LEFT OF THE

OPTIONAL FEATURE IF IT HAS BEEN ACTIVATED IN YOUR SYSTEM.

 Passive Operation

 Auto Lock & Unlock from ignition key

 Optional Interior Illumination Relay

 Starter interrupt

 Channel 2 Optional Accessory

REMOTE DOOR LOCKING:

1. Turn off the engine, exit the vehicle, and close all doors.

2. Press and release the Lock/Unlock button on the keychain transmitter.

The vehicle's doors will lock.

3. The vehicle's starter is now interrupted, and the car cannot bestarted, even

when using the ignition key.

BACK UP PASSIVE OPERATION:

The system can be programmed to operate automatically when you leave the

car. This programming must be done by the installer during the installation.

The Passive feature works as follows;

1. Turn off the engine, exit the vehicle, and close all doors.

2. In 30 seconds, the vehicle's starter will automatically be interrupted. If the

passive lock feature was selected on at time of installation, then the doors

will lock automatically in 30 seconds.

OPTION NOTE: The system can be programmed to either...

Automatically lock the doors, or only lock the doors when the transmitter is

operated. Check with your installation center for programming of this feature.

REMOTE DOOR UNLOCKING:

1. As you approach the vehicle, press and release Lock/Unlock button on the

keychain transmitter.

2. The vehicle's doors will unlock, and the starter interrupt system is

disengaged allowing you to start the vehicle.

3. Never attempt to unlock the doors from a distance that will prevent you

from starting the vehicle within 30 seconds if the system has been

programmed for passive operation. If you do this, and the vehicle will not

start, simply press and release the lock/unlock button again.

OPTION NOTE: If the optional interior illumination relay has been

installed in your vehicle, then the dome light will turn on for 30 seconds

during step 1 above. If you turn the ignition switch on during the 30

second timer, then the dome light will turn off.

CHANNEL 2 OUTPUT:

The system has an additional output that can be wired to a number of different

optional accessories. Some examples of these optional accessories are;

– Remote Trunk Release

– Remote Car Starter

– Remote Window Roll Up

To activate the optional accessory;

1. Press and hold the "Option" button on the keychain transmitter for

approximately 3 seconds.

2. The optional accessory that has been connected to channel 2 will now

engage.

AUTO LOCK & UNLOCK:

The system can be programmed for automatic lock when the ignition switch

is turned on and for automatic unlock when the ignition switch is turned off.

When this feature is activated, approximately 3 seconds after turning the

ignition key to the on position, all doors will lock only if all doors are closed.

When the key is turned to the off position, all doors will immediately unlock.

VALET SYSTEM OVERRIDE SWITCH:

The "valet" switch allows you to temporarily by-pass the starter interrupt

feature, eliminating the need to hand your keychain transmitter to parking

attendants or garage mechanics. Whenthesystemisinvalet mode, all features

except the starter interrupt will remain operational. To use the valet mode;

1. Enter the vehicle, and turn the ignition key to the on position.

2. Move the valet toggle switch to the on position.

3. To return to normal operation, move the valet switch to the off position any

time the ignition key is on.

In the event that you lose your transmitter, or if the transmitter fails to operate

when you return to the vehicle, the valet switch can be used as a system

override switch. Turn the ignition key on, and move the valet switch to the on

position. The vehicle can now be started.

NOTE: Always remember to move the valet switch back to the off

position. This will ensure that the vehicle remains protected at all

times.

PROGRAMMING NEW OR ADDITIONAL TRANSMITTERS:

The system can be programmed to accept the codes from 4 different

transmitters. To program transmitters, it is always best to have all transmitters

that will operate the system with you during the programming. To program the

transmitters, be sure to follow all steps in exact order, and do not wait more

that 10 seconds between any 2 steps.

1. Turn the ignition key to the on position.

2. Move the valet switch on, off, on, off, on, then off.

If the optional illuminated entry feature has been installed, the dome

light will flash one time.

3. Press and hold the "Lock/Unlock" button on the first transmitter for

4 seconds.

If the optional illuminated entry feature has been installed, the dome

light will turn on for approximately 1.5 seconds when the transmitter

is accepted.

4. Repeat step 3 for all transmitters up to a total of four.

5. Move the valet switch on then off.

If the optional illuminated entry feature has been installed, the dome

light will flash two times.

6. Press and hold the "Option" button on the first transmitter for 4 seconds.

If the optional illuminated entry feature has been installed, the dome

light will turn on for approximately 1.5 seconds when the transmitter

is accepted.

7. Repeat step 6 for all transmitters up to a total of four.

8. Turn the ignition key off, and test all transmitters.

9. If any transmitter is not working, repeat the entire procedure.

TRANSMITTERBATTERY REPLACEMENT

You will notice a decrease in transmitter range as the battery condition

deteriorates. Transmitter battery replacement is recommended at least every

10 to 12 months, depending upon how frequently the transmitter is used.

The transmitter has a small red L.E.D. built into the case. This L.E.D. can be

used to indicate battery condition. If the L.E.D. does not illuminate, then the

battery is discharged, and must be replaced.

To replace the transmitter battery,

1. Remove the small phillips head screws from the bottom cover of the

transmitter.

2. Carefully unsnap the top cover of the transmitter from the bottom cover.

3. Remove the discharged battery, making note of the location of the + and

– contacts, and replace with a new type GP 27A 12 volt battery.

4. Replace the transmitter cover, taking care not to damage the L.E.D. or

switches on the circuit board, and secure with the small phillips head screw.

1-800-645-4994

128-5392

ORDER FORM FOR 2 BUTTON TRANSMITTER

MODEL NO. PRO OE2 w/ PD-21

IMPORTANT : To help us expedite your order, please print all of the information legibly,

and mail this form and your payment according to the instructions below.

1. Name : ___________________________________________________________

Address : ___________________________________________________________

City : _____________________ State : _______ Zip Code : __________________

2. Telephone Number : ( _______ ) ______________________________________

3. Enter the total number of transmitters required here : ______________________

4. The cost per transmitter is $ 65.00.

5. Enter the total amount enclosed here : __________________________________

( New York state residents must include the appropriate sales tax.)

6. Method of payment; check one of the boxes below.

 Mastercard  Visa  Check or money order*(donotsend cash )

* Make checks payable to Audiovox Corporation

7. Credit Card Number : ________________________________________________

8. Credit Card Expiration Date : _____________________

Credit card purchasers can order additional or replacement transmitters by

phone. Simply dial 1 - 800 - 645 - 4994, and follow the instructions from the

operator interface.

9. Mail this form, and your check, to ;

Audiovox Corporation

150 Marcus Blvd.

Hauppauge, N.Y., 11788

Attn. : TRANSMITTER DEPARTMENT

Audiovox Pursuit PRO 9445FT Owner's manual

Related papers

Other documents