2. Truck Slide
  3. 4312-028
4312-028

Truck Slide 4312-028, 4312-002, 4312-003, 4312-004, 4312-008, 4312-009, 4312-013 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Truck Slide 4312-028 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
NOTE:
505-00033 TRUCK SLIDE MAT SHOWN.
OTHER CONFIGURATIONS WILL VARY SLIGHTLY,
BUT WILL NOT AFFECT ASSEMBLY.
DRILL/ DRIVER
Rev. AA
Installation Instructions: TRUCK SLIDE MAT
PART# 505-00033
SAFETY GLASSES TAPE MEASUREDRIVER BIT SET
person is required for lifting and installing of this product.
Pg. 1
Attention Read all instructions and understand all warnings before installing or using this product.
Notes
Do not over tighten hardware.
Tools Required
•
Perform all work on dry level ground.•
Insure vehicle's parking break is engaged and wheels are
chocked.
•
Use safety glasses when using tools or working under vehicle.• Due to the size and weight of products more than one •
Danger of Injury
Team lift is required for installation of this product.
Moving parts in this assembly can cause injury.
2
3
1
PART# 505-00033
Installation Instructions: TRUCK SLIDE MAT
Rev. AA
Note: Take inventory of all
provided parts prior to assembly.
Pg. 2
Provided Parts
ITEM
NO.
PART NUMBER QTY.
1 040-05062, DIAMOND RUBBER MAT 1
2 285-00213, 5/8" X 48" ANGLE 2
3 030-05014, 10-16X1" SELF TAP SCREW 8
Rev. AA
Installation Instructions: TRUCK SLIDE MAT
PART# 505-00033
Pg. 3
STEP 1:
PLACE RUBBER MAT DIAMOND PLATE
SIDE UP IN TRUCK SLIDE
AS SHOWN IN FIGURE 1
STEP 2:
ALIGN MAT WITH REAR CORNERS OF
TRUCK SLIDE
AS SHOWN IN FIGURE 2
STEP 3:
PLACE 5/8" ANGLE ON TOP OF RUBBER MAT
AND AGAINST REAR FACE OF TRUCK SLIDE
AS SHOWN IN FIGURE 3
FIGURE 2
FIGURE 1
FIGURE 3
REAR FACE OF TRUCK SLIDE
RUBBER MAT
5/8" ANGLE
RUBBER MAT
TRUCK SLIDE REAR FACE
SCREW 10-16X1"
SELF TAPPIING
FIGURE 4.2FIGURE 4.1
SELF TAP SCREW LOCATIONS
FIGURE 5
Rev. AA
Installation Instructions: TRUCK SLIDE MAT
PART# 505-00033
Pg. 4
STEP 4:
FIRMLY HOLD DOWN ANGLE AND SECURE
IN PLACE WITH SELF TAPPING SCREWS (QTY 4)
AS SHOWN IN FIGURE 4.1 AND 4.2
STEP 5:
PULL MAT TIGHT AND ALIGN WITH
FRONT EDGE OF TRUCK SLIDE
AS SHOWN IN FIGURE 5
RUBBER MAT
FRONT EDGE
SCREW 10-16X1"
SELF TAPPIING
FIGURE 6
5/8" ANGLE
FIGURE 7.1
FIGURE 7.2
RUBBER MAT
Installation Instructions: TRUCK SLIDE MAT
Rev. AAPART# 505-00033
Pg. 5
STEP 6:
CAPTURE FRONT EDGE OF MAT WITH
5/8" ANGLE AND LOCATE
AS SHOWN IN FIGURE 6
STEP 7:
FIRMLY HOLD DOWN ANGLE AND SECURE
IN PLACE WITH SELF TAPPING SCREWS (QTY 4)
AS SHOWN IN FIGURE 7.1 AND 7.2
SELF TAP SCREW
LOCATIONS
/