Halo SMD4S6940WH User guide

Brand: Halo

Model: SMD4S6940WH

Type: User guide

SMD - Surface LED Downlight Series

Dimming Guide and Step-down Transformer Application Note

The SMD LED Series provides continuous dimming with reverse or forward phase cut dimmers; as low as 5% depending upon

dimmer and low-end trim of the dimmer.

120V AC dimmed power

to Halo Surface

LED Downlights

120V AC Power

(2 wire + Gnd typical)

120V AC dimmed power

to Halo Surface

LED Downlights

120V AC Power

(2 wire + Gnd typical)

HALO

Figure 1

Recessed Housing

Installation

Figure 2

Direct Mount

Installation

SMD4 SMD4-DM SMD6 SMD6-DM

SMD4R6927WH

SMD4R6930WH

SMD4R6935WH

SMD4R6940WH

SMD4R6950WH

SMD4S6927WH

SMD4RS930WH

SMD4RS935WH

SMD4RS940WH

SMD4RS950WH

SMD4R6927WHDM

SMD4R6930WHDM

SMD4R6935WHDM

SMD4R6940WHDM

SMD4R6950WHDM

SMD4S6927WHDM

SMD4RS930WHDM

SMD4RS935WHDM

SMD4RS940WHDM

SMD4RS950WHDM

SMD6R6927WH

SMD6R6930WH

SMD6R6935WH

SMD6R6940WH

SMD6R6950WH

SMD6S6927WH

SMD6RS930WH

SMD6RS935WH

SMD6RS940WH

SMD6RS950WH

SMD4R6927WHDM

SMD4R6930WHDM

SMD4R6935WHDM

SMD4R6940WHDM

SMD4R6950WHDM

SMD4S6927WHDM

SMD4RS930WHDM

SMD4RS935WHDM

SMD4RS940WHDM

SMD4RS950WHDM

*Note: The Rapid Start feature is used to ensure the right amount of power boost during start-up. When a dimmer with Rapid Start is turned on from a low dimmer setting,

the LED lighting may exhibit a momentary ﬂash. Select dimmer models offer an adjustment of the Rapid Start feature. The user may wish to adjust this setting to reduce the

boost and resulting momentary ﬂash. If this capability is desired, the user should select dimmer models designated as “fully adjustable” or “selectable ON or OFF”.

Eaton's AL Series dimmers offer versatile options

to set the mood and reduce energy consumption.

Visit www.cooperwiringdevices.com/ALSeries for

more information.

Dimmer Features

Decorator dimmer

DAL06P/WBSD-DEC

Slide dimmer

SAL06P/WBSD-SLD

Toggle dimmer

TAL06P/WBSD-TOG

Rapid Start feature* Fully adjustable Fixed ON Fully adjustable

Adjustable high-end trim

Adjustable low-end trim • • •

Wiring configurations Single-pole or 3-way Single-pole or 3-way Single-pole or 3-way

Color change kits • •

Phase Control 120V Dimming

PA518082EN

February 9, 2017

Dimmer

Make

Dimmer

Series

Dimmer

Model #

Types Of Dimmer Minimum

Luminaires

(per circuit)

Maximum

Recommended

Luminaires

(per circuit)

Min Dimming

percentage

(%)

Max Dimming

percentage

(%)

Low End

Start-up time

EATON Decorator DAL06P

Triac (INC/HAL/MLV/ELV/CFL/

LED)

1 23 3% 98% <1s

EATON Toggle TAL06P

Triac(INC/HAL/MLV/ELV/CFL/

LED)

1 23 4% 98% <2s

EATON Slide SAL06P

Triac(INC/HAL/MLV/ELV/CFL/

LED)

1 23 4% 98% <1s

EATON Slide SLC03P Triac (INC/HAL/CFL/LED) 1 23 4% 98% <1s

EATON Toggle DLC03P Triac (INC/HAL/CFL/LED) 1 23 4% 98% <1s

EATON iLumin SC277-06-UN Control Panel( Leading Edge) 1 38 3% 97% <3s

Lutron Diva DVCL-153P 1 11 4% 97% <1s

Lutron Toggler TGCL-153P 1 11 4% 97% <1s

Lutron Maestro MACL-153-M 1 11 4% 97% <1s

Lutron Skylark SCL-153P-WH 1 11 4% 97% <1s

Lutron LC128 LP-RPM-4U-120 1 150 4% 98% <1s

Lutron LC128 LP-RPM-4A-120 1 94 1% 97% <3s

Leviton SureSlide 6674 1 11 6% 97% <1s

Leviton Illumatech IPL06 1 11 4% 97% <2s

Legrand

Pass&Seymour

Harmony

H703PTUW 1 35 4% 99% <1s

Dimmer Rating - Load Type

INC = Incandescent

HAL = Halogen

MLV = Magnetic Low Voltage

ELV = Electric Low Voltage

CFL = Compact Fluorescent

LED Rated Dimmers

Eaton SLD Dimming Guide - PA518058EN

Dimmer

Make

Dimmer

Series

Dimmer

Model #

Types Of Dimmer Minimum

Luminaires

(per circuit)

Maximum

Recommended

Luminaires

(per circuit)

Min Dimming

percentage

(%)

Max Dimming

percentage

(%)

Low End

Start-up time

EATON Toggle TI061 Triac (INC/HAL ) 1 47 3% 95% <1s

EATON Aspire 9530AW Triac(INC) 1 47 3% 100% <3s

EATON Rotary RI061 Triac(INC/HAL) 1 47 15% 98% <1s

EATON Slide SF8AP 1 76 20% 98% <1s

EATON Decorator DE06P ELV 1 47 3% 96% <3s

Lutron Toggler TG-600P Triac (INC ) 1 47 1% 97% <7s

Lutron Diva DV-600P Triac (INC ) 1 47 4% 97% <1s

Lutron Lumea LG600P Triac (INC/HAL ) 1 47 6% 97% <1s

Lutron Skylark S-600P Triac (INC/HAL ) 1 47 3% 97% <1s

Lutron Skylark Contour CT103P Triac (INC/HAL/MLV) 1 79 3% 97% <1s

Lutron Diva DV603P Triac (INC/HAL ) 1 47 4% 97% <1s

Lutron Nova T NTFTU-5A Triac (Fluorescent ) 1 47 16% 97% <1s

Lutron Maestro MAELV600 ELV 1 47 4% 97% <1s

Lutron Faedra FAELV500 ELV 1 39 4% 97% <1s

Lutron Diva DVELV303P ELV 1 23 1% 97% <2s

Lutron Skylark SELV300P ELV 1 23 1% 97% <2s

Leviton Decora 6673 Triac (CFL/INC) 1 47 30% 97% <1s

Leviton SureSlide 6631-2 Triac (INC ) 1 47 4% 97% <1s

Leviton IPI06 1 47 4% 97% <3s

Leviton Vizia VP106 Triac (INC ) 1 47 4% 97% <1s

Leviton Decora 6161 Triac (INC ) 1 39 4% 97% <1s

Leviton Sure Slide 6633-P 1 47 4% 97% <1s

Leviton

Plug In Lamp

Dimmer

TBI03 Triac 1 23 3% 99% NA

Leviton Vizia VPE06 ELV 1 47 4% 97% <1s

Leviton Illumatech IPE04 ELV 1 23 6% 97% <1s

Leviton Vizia VZE04 ELV 1 31 4% 97% <1s

Lutron Ariadni AY-600P 1 47 1% 97% <6s

Lutron Contour CT-103P 1 79 3% 97% <1s

Lutron Contour CT-600P 1 47 3% 97% <1s

Lutron Rotary D-600P 1 47 20% 97% <1s

Lutron Diva DV-600P 1 47 3% 97% <1s

Lutron Glyder GL-600P 1 47 3% 97% <1s

Lutron Lumia LG-600PH 1 47 3% 97% <1s

Lutron Maestro MA600 1 47 3% 97% <1s

Lutron Nova N-600 1 47 4% 97% <1s

Lutron Skylark S-600P 1 47 3% 97% <1s

Lutron Centurion C-600P 1 47 0% 98% NA

Lutron Ariadni AYLV-600P 1 35 1% 3% <7s

Lutron Glyder GLV-600 1 35 3% 97% <1s

Lutron Diva DVLV-600P 1 35 0% 97% NA

Lutron Lumina LG-103P 1 79 3% 97% <1s

Lutron Skylark SLV-600P 1 35 3% 97% <1s

Lutron Vierti VT-600 1 47 4% 97 NA

Lutron Nova NTLV-600 1 35 3% 97% <2s

Lutron Nova NT-600 1 47 0% 97% NA

1. Will not illuminate at low end start up.

Testing conducted by Eaton's lighting division is not a substitute for and does not imply certification by an independent laboratory or any other standards certification.Refer

to manufacturer specifications for more detailed information on product certifications and standards. Refer to this dimming guide notes section. Consult the dimmer manu-

facturer prior to installation to ensure compatibility.

Incandescent and Electronic Low Voltage Rated Dimmers - For Reference Only

Dimmer Rating - Load Type

INC = Incandescent

HAL = Halogen

MLV = Magnetic Low Voltage

ELV = Electric Low Voltage

CFL = Compact Fluorescent

Eaton SLD Dimming Guide - PA518058EN

Dimmer Notes:

1. Start time is measured at the lowest dimmer setting.

2. Some LED rated dimmers have a "rapid start" design used to provide a momentary power boost for LED and CFL

lamps during start-up. When a LED luminaire is on a dimmer with "rapid start" the boost may cause a momentary

flash of the LED lighting. This "flash" is generated by the dimmer, and may be more noticeable when the dimmer

is at a low setting. A solution is available in the following EATON dimmers which provide adjustment capability of

the "rapid start": Decorator (DAL06P), Smart (AAL06), and Toggle (TAL06P). Refer to product specifications online at

www.cooperwiringdevices.com for more details.

Dimming Guide Disclaimer:

1. Leviton

is a registered trademark of Leviton Manufacturing Co. Inc.; Lutron

is a registered trademark of Lutron

Electronics Co. Inc.; Lightolier

is a registered trademark of Philips Lighting; Hubbell

is a registered trademark of

Hubbell Incorporated; Legrand

and Pass & Seymour

are registered trademarks of Legrand

. These companies and

their tradenames, trademarks or brands, where noted, are associated with their respective company and are not

associated with EATON.

2. Testing conducted by EATON is not a substitute for and does not imply certification by an independent laboratory or

any other standards certification. Refer to the manufacturer specifications for more detailed information on product

certifications and standards.

3. This is a representative list of typical dimmers as tested by EATON for performance with the designated LED

luminaires only. Test data contained in this literature is based upon dimmers obtained in the marketplace. 

• Information about these other manufacturers products is obtained from packaging and published information

made available by the manufacturer and is deemed to be reliable, but has not been verified. 

• Dimmer performance and perceived limitations of the dimmers are based onfactors outside of EATON's control.

• The specifications of these dimming controls and their conditions of use may change without notice to EATON or

any other user. 

• EATON makes no specific recommendation on product selection and there are no warranties of performance or

compatibility implied. 

• Installer must ensure proper local and national electrical codes are followed; and that the dimmer application and

condition of use is per dimmer manufacturer instructions and guidelines.

Eaton SLD Dimming Guide - PA518058EN

Transformer Load - H277 (300VA)

1. H277 Transformer at full loading consumes a maximum of 16W of power.

2. When a dimmer or switch is on the secondary (120V) side of the transformer,

power is consumed by the transformer when the dimmer or switch is in “OFF”

mode at 6.5W and in “ON” mode at 16W maximum under full loading.

3. When a switch is on the primary (277V) side ahead of the transformer, power is

consumed only in “ON” mode to a maximum of 16W under full loading. (Use of a

dimmer ahead of the transformer is not recommended)

Transformer Load - H347 (75VA)

1. H347 Transformer at full loading consumes a maximum of 15W of power.

2. When a dimmer or switch is on the secondary (120V) side of the transformer,

power is consumed by the transformer when the dimmer or switch is in “OFF”

mode at 2.5W and in “ON” mode at 15W maximum under full loading.

3. When a switch is on the primary (347V) side ahead of the transformer, power is

consumed only in “ON” mode to a maximum of 15W under full loading.

(Use of a dimmer ahead of the transformer is not recommended)

Transformer Load - H347200 (200VA)

1. H347200 Transformer at full loading on 120V side consumes a maximum of 28W

of power.

2. When a dimmer or switch is on the secondary (120V) side of the transformer,

power is consumed by the transformer when the dimmer or switch is in “OFF”

mode at 9.2W and in “ON” mode at 28W maximum under full loading.

3. When a switch is on the primary (347V) side ahead of the transformer, power is

consumed only in “ON” mode to a maximum of 28W under full loading.

When a switch is on the primary (277V) side ahead of the transformer, power is

consumed only in “ON” mode to a maximum of 12W under full loading.

(Use of a dimmer ahead of the transformer is not recommended)

Step Down Transformers

H277 = Steps 277 line voltage down to 120 volts. Attaches to knockout on ﬁrst ﬁxture’s

junction box in a circuit and is 300VA rated. H277 is a UL recognized Component listed

under the luminaire UL/cUL listing for Halo Non-IC housings.

H347 and H347200 = Steps 347 line voltage down to 120 volts. Attaches to knockout

on ﬁrst ﬁxture’s junction box in a circuit. H347 is 75VA and H347200 is 200VA rated.

H347 is a CSA/UL Listed Component for use under the luminaire UL/cUL listing with

Halo Non-IC housings.

H347

347V Step Down Transformer,

75VA

2-7/8

2-1/2”

[63mm]

2-3/4”

[70mm]

H347

H347200

347V Step Down Transformer,

200VA

2-7/8

2-3/16”

[56mm]

4-3/4”

[121mm]

H347200

H277

277V Step Down Transformer,

300VA

2-7/8

2-3/16”

[56mm]

4-3/16”

[106mm]

H277

Application Note

H277, H347 and H347200 step-down transformers are qualiﬁed to drive multiple Halo LED on a single circuit in Non-IC

construction. Installation of these transformers with individual LED ﬁxtures on circuits with multiple LED loads is not

recommended. This is not recommended due to resulting multiple inductive currents pulled by each transformer; in

this situation the majority of the power would then be reactive (VARS) and not real (WATTS). If H277, H347 or H347200

transformers should be used individually on each LED ﬁxture in a single circuit, then that circuit should be sized for

lowered power factor as well as increased apparent power on the circuit. H277, H347 and H347200 are UL/cUL listed for

use with Halo recessed housings: H750T, H750TCP, H7T, H7TNB, H7RT.

SMD - Surface LED Downlight Series

SMD Maximum Units on Step Down Transformer

Powered Circuits

SMD4, SMD6 - 80 CRI

SMD4 - 90 CRI SMD6 - 90 CRI

VA Rating Max # of Fixtures Max # of Fixtures

H277

300 18 16

H347

75 4 4

H347200

200 12 10

Eaton SLD Dimming Guide - PA518058EN

Ground

277V

120V

Hot

Transformer

Switch*

Neutral

LED LED LED

Transformer with Switch on 277V Primary

347V Switch*

347V

120V

Hot

Transformer

Neutral

LED LED LED

Ground

Transformer with Switch on 347V Primary

277V

(347V)

120V

Hot

Transformer

Hot

Neutral

LED LED LED

Ground

Transformer with Dimmer/Switch on 120V Secondary

Dimmer Neutral Connection typical with some Dimmers

120V Dimmer or Switch

*Use of a dimmer ahead of the transformer is not recommended

Eaton

1121 Highway 74 South

Peachtree City, GA 30269

P: 770-486-4800

www.eaton.com/lighting

Specifications and

dimensions subject to

change without notice.

Halo SMD4S6940WH User guide

Halo SMD4S6940WH User guide

Halo SMD4S6940WH User guide

Related papers

Other documents