Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
MITK890 Mounting Kit
Mitsubishi
1995-05 ECLIPSE
2000-04 MONTERO SPORT
2003-06 OUTLANDER
Eagle
1995-98 TALON
VEHICLE APPLICATIONS
iMITK890
©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 12/13 PRINT Ver. 12/13
2 7
1995-98 EAGLE TALON
1995-99 MITSUBISHI ECLIPSE
1. Carefully unsnap the trim bezel from around the radio starting at the top,
and remove trim bezel.
2. Remove the (2) Phillips screws from the radio opening securing the top of the
lower console to the sub-dash.
3. Gently lift up and remove the ashtray/drink holder from the center console.
4. Remove the (2) Phillips screws under ashtray / drink holder location.
5. Remove the (2) Phillips screws (1) from each rear side of the center console.
6. Carefully lift center console upward, disconnect the light from inside the ashtray/drink
holder location.
7. Disconnect the connections on the lighter receptacle, and remove the center console.
8. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
9. Carefully pull radio forward, disconnect wire harness and antenna lead and
remove the radio.
*SEE note below
see back page
for kit assembly
instructions
EXPLODED VIEW OF
UPPER CONSOLE
MOUNTING HOLE LOCATIONS
SPEED CLIP
*NOTE: MUST REMOVE SPEED CLIPS
FROM SUB-DASH. CAREFULLY FILE
1/8” FROM LEFT AND RIGHT INSIDE
EDGE OF CONSOLE MOUNTING
LOCATIONS (SEE SHADED AREAS
ABOVE). RE-INSERT SPEED CLIPS
FROM BOTTOM EDGE FACING UP.
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
SUB-DASH PREPARATION
SPEED CLIP
NOTES
4 5
1. Remove the (2) Phillips screws from the trim bezel below the radio.
2. Gently lift upward from the bottom of the dash trim bezel and pull the top of the trim
bezel towards you to release the (2) spring retaining clips.
3. Disconnect the hazard harness from the dash trim bezel and remove the trim bezel.
4. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
5. Pull the radio forward, disconnect the harnesses and antenna lead and remove the radio.
2000-05 MITSUBISHI ECLIPSE
2000-04 MITSUBISHI MONTERO SPORT
1. Carefully remove the trim bezel from around the radio using a panel removal tool.
2. Remove the (4) Phillips screws securing the radio to the sub-dash.
3. Carefully pull the radio forward, disconnect the wire harness and antenna leads and remove the radio.
FOR DIN & ISO MOUNT
APPLICATIONS
INSERT SPACERS INTO BRACKETS ON
BOTH SIDES ONLY WHEN ISO
MOUNTING RADIO
REMOVE only
lower shaded tabs
on both left & right
BRACKETS
REMOVE
FOR DIN AND ISO MOUNT
APPLICATIONS
Note:
ISO Brackets are only required when
ISO mounting Radio. Remove all shaded
areas on both Left and right iso brackets
(see figure a)
2000-01 montero sport
Fig.A
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
KIT ASSEMBLY
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
KIT ASSEMBLY
ITR-890 Trim Ring
(Optional Use)
ITR-890 Trim Ring
(Optional Use)
1. Carefully pull and remove the (3) knobs from the climate controls.
2. Remove the Phillips screws from each climate control knob location.
3. Carefully pry radio trim panel forward and remove trim.
4. Remove the (4) Phillips screws securing the factory radio to the subdash.
5. Carefully pull radio forward, disconnect the wire harness and antenna
adapter and remove radio.
2003-06 MITSUBISHI OUTLANDER
FOR DIN & ISO MOUNT
APPLICATIONS
INSERT SPACERS INTO BRACKETS
ON BOTH SIDES ONLY WHEN ISO
MOUNTING RADIO
REMOVE ALL
shaded tabs on
both left & right
BRACKETS
REMOVE shaded
BRACKETS on both
left & right SIDES
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
KIT ASSEMBLY
ITR-890 Trim Ring
(Optional Use)
6 3
1995-98 EAGLE TALON
1995-99 MITSUBISHI ECLIPSE
FOR DIN AND ISO MOUNT
APPLICATIONS
INSERT SPACERS INTO
BRACKETS ON BOTH SIDES ONLY
WHEN ISO MOUNTING RADIO
*REMOVE shaded areas
only on both sides of
BRACKETS FOR
95-99 ECLIPSE/TALON
APPLICATIONS
*note: remove only outer half of upper mounting tab
on ISO bracket part Imb-890 R
remove only the 3 parallel side mounting tabs on part
Imb-890 l (See figure b)
Do not remove
this piece
Fig. B
KIT ASSEMBLY
DIN MOUNT INSTRUCTIONS
1. Insert DIN sleeve from your new radio into the upper section of the installation kit.
(This DIN sleeve comes with all new radios and slides off the back of the radio)
2. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
3. Install radio into sleeve and lock into place.
4. Support rear of radio with back strap.
Optional use Trim Ring (ITR-890) may be used on some radios if desired.
Due to the movement of some faces on some radios our ISO Trim Ring may not be able
to be used.
Your new radio must have a trim ring around the face of the radio that is designed to be
easily removed. Consult your radio ownerʼs manual.
DIN Sleeve
ITR-890 Trim Ring
(Optional Use)
ITR-890 Trim Ring
(Optional Use)
NOTES
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Discount Car Stereo BKMBK100C Operating instructions
-
Metra 99-7001 Installation guide
-
American International HYNK1133 User manual
-
Metra 88-00-9006 Operating instructions
-
-
Thule 103 User manual
-
American International KIAK1240 User manual
-
Metra Electronics 99-7006 User manual
-
Scosche FCJ1276AB Installation guide
-
