Contec COM-4(LPCI)H Owner's manual

Contec
Brand
Contec
Model
COM-4(LPCI)H
Type
Owner's manual

This manual is also suitable for

CONTEC CO., LTD.
TECHNICAL REFERENCE
RS-232C 1ch Serial I/O Board for Low Profile PCI
COM-1(LPCI)H
RS-232C 2ch Serial I/O Board for Low Profile PCI
COM-2(LPCI)H
RS-232C 4ch Serial I/O Board for Low Profile PCI
COM-4(LPCI)H
RS-232C 8ch Serial I/O Board for Low Profile PCI
COM-8C-LPCI
Contents
1. Introduction ...................................................................................................................... 2
1.1. Terminology .............................................................................................................. 2
2. Product Information ......................................................................................................... 2
2.1. Vendor ID and Device ID ......................................................................................... 2
2.2. Obtaining the Resources ........................................................................................... 2
3. I/O Port Bit Allocation ..................................................................................................... 3
3.1. I/O Address Map ....................................................................................................... 3
3.2. Details on I/O Ports and Registers ........................................................................... 4
3.3. Interrupt Vector Register .......................................................................................... 8
4. Operation Procedure ........................................................................................................ 9
4.1. Access to I/O Ports .................................................................................................... 9
4.2. Interrupt function ...................................................................................................... 9
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
2/9
August 31, 2017
1. Introduction
This document provides reference concerning I/O port bit allocation as well as the definition of each bit. It is
intended for those who are not using our support software or developing applications on non-Windows
environment.
1.1. Terminology
Definition of terms:
I/O Base Address
It is the smallest value of I/O resources (I/O range) allocated to a board and is synonymous with top I/O address.
Usually, an I/O address of a board means this address.
CH Base Address
The CH base address of each channel is the smallest value of I/O resources (the range of I/O addresses) allocated
to that channel, meaning the same as the channel's start address.
2. Product Information
2.1. Vendor ID and Device ID
Information specific to each product is as follows.
Vendor ID : 1221h
Device ID :
Board Name
Device ID
COM-1(LPCI)H
8171h
COM-2(LPCI)H
8181h
COM-4(LPCI)H
8191h
COM-8C-LPCI
9131h
Revision ID : Board ID setup switch (SW1) status. Reflected in the range between 00h and 0Fh.
Technical data excluding those provided above is compliant with PCI local bus specifications.
2.2. Obtaining the Resources
The library for allocating resources (I/O base address, interrupt level, and memory base address) to the PCI bus
board in the MS-DOS environment is stored in \Pci\Dos\Samples on the bundled disk "Standard COM Driver
Software/COM Setup Disk." Use the library for reference and operation check purposes in your program
development.
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
3/9
August 31, 2017
3. I/O Port Bit Allocation
3.1. I/O Address Map
This board uses the XR16C2850 (manufactured by Exar Corporation) which is upward compatible from the UART
16550.
For details on the internal registers and control of the XR16C2850, refer to the XR16C2850 Data Sheet.
- I/O Port
I/O Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
Channel 1 register
|
+7h
+8h
Channel 2 register(*1)
|
+Fh
+10h
Channel 3 register (*1)(*2)
|
+17h
+18h
Channel 4 register (*1)(*2)
|
+1Eh
+1Fh
Interrupt Vector Register 1
+20h
Channel 5 register (*1)(*2)(*3)
|
+27h
+28h
Channel 6 register (*1)(*2)(*3)
|
+2Fh
+30h
Channel 7 register (*1)(*2)(*3)
|
+37h
+38h
Channel 8 register (*1)(*2)(*3)
|
+3Eh
+3Fh
Interrupt Vector Register 2
(*1)The COM-1(LPCI)H cannot use channel 2 - 8 (+8h - +1Eh, +20h - +3Fh).
(*2)The COM-2(LPCI)H cannot use channel 3 - 8 (+10h - +1Eh, +20h - +3Fh).
(*3)The COM-4(LPCI)H cannot use channel 5 - 8 (+20h - +3Fh).
Access to each port must be performed in bytes for device specification reasons.
Ports can be accessed only in bytes (neither in words nor in double words).
C
A
UT
IO
N
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
4/9
August 31, 2017
3.2. Details on I/O Ports and Registers
The XR16C2850's internal registers vary in port map, depending on the value set in the Line Control Register
(LCR).
The general registers are enabled either upon startup or unless LCR bit 7 is 0 and the LCR is 0xBF.
The baud registers are enabled when LCR bit 7 is 1.
The enhanced registers are enabled when the LCR is 0xBF.
The CH base address of each channel in the table below is as follows:
CH Base Address of channel 1 I/O Base Address + 0h
CH Base Address of channel 2 I/O Base Address + 8h
CH Base Address of channel 3 I/O Base Address + 10h
CH Base Address of channel 4 I/O Base Address + 18h
CH Base Address of channel 5 I/O Base Address + 20h
CH Base Address of channel 6 I/O Base Address + 28h
CH Base Address of channel 7 I/O Base Address + 30h
CH Base Address of channel 8 I/O Base Address + 38h
- Input Port 1 (General Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
Receive Holding Register (RHR)
Data Bit 7
Data Bit 6
Data Bit 5
Data Bit 4
Data Bit 3
Data Bit 2
Data Bit 1
Data Bit 0
+1h
Interrupt Enable Register (IER)
CTS
Interrupt
(*2)
RTS
Interrupt
(*2)
Xoff
Interrupt
(*2)
Sleep
Mode
(*2)
MODEM
Status
Interrupt
Receive
Line
Status
Interrupt
Transmit
Holding
Register
Receive
Holding
Register
+2h
Interrupt Status Register (ISR)
FIFOs
Enable
FIFOs
Enable
RTS-CTS
Change
(*2)
Xoff/Special
Char
(*2)
Int
Priority
Bit 2
Int
Priority
Bit 1
Int
Priority
Bit 0
Int
Status
+3h
Line Control Register (LCR)
Divisor
Latch
Enable
Set
Break
Set
Parity
Even
Parity
Parity
Enable
Stop
Bits
Word
Length
Bit 1
Word
Length
Bit 0
+4h
Modem Control Register (MCR)
Clock
Prescaler
Select
(*2)
IR
Mode
Enable
(*2)
Xon
Any
(*2)
Loop
Back
Enable
-OP2 and
INT
Enable
Out 1
0:INT
Enable
1:INT
Disable
(*1)
-RTS
-DTR
+5h
Line Status Register (LSR)
FIFO
Error
THR&
TSR
Empty
THR
Empty
Break
Interrupt
Framing
Error
Parity
Error
Overrun
Error
Receive
Data
Ready
+6h
Modem Status Register (MSR)
-CD
-RI
-DSR
-CTS
Delta
-CD
Delta
-RI
Delta
-DSR
Delta
-CTS
+7h
Scratch Pad Register (SPR) (*4)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+7h
FIFO Level Counter (FLVL) (*3)(*4)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(*1)For details, see the method of using interrupts.
(*2)This bit is enabled when EFR bit 4 is 1.
(*3)This register is enabled when FCTR bit 6 is 1.
(*4)As the COM-4(LPCI)H uses "+7h (I/O base address + 1Fh) of channel 4" as an interrupt vector register, it can use neither the scratch pad
register nor the FIFO level counter of channel 4.
As the COM-8C-LPCI uses "+7h (I/O base address + 1Fh) of channel 4"and "+7h (I/O base address + 3Fh) of channel 8" as an interrupt vector
register, it can use neither the scratch pad register nor the FIFO level counter of channel 4 and channel 8.
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
5/9
August 31, 2017
- Input Port 2 (Baud Rate Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
LSB of Divisor Latch (DLL)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+1h
MSB of Divisor Latch (DLM)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
- Input Port 3 (Enhanced Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
Trigger Level / FIFO Data Count Register
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
+1h
Feature Control Register (FCTR)
Rx/Tx
Mode
SCPAD
Swap
Trig
Bit 1
Trig
Bit 0
RS485
Auto
control
IrRx
In v.
-RTS
Delay
Bit 1
-RTS
Delay
Bit 0
+2h
Enhanced Feature Register (EFR)
Auto
-CTS
Auto
-RTS
Special
Char,
select
Enable
IER
Bits 4 - 7,
ISR, FCR
Bits 4 - 5,
MCR
Bits 5 - 7
Cont-3
Tx, Rx
Control
Cont-2
Tx, Rx
Control
Cont-1
Tx, Rx
Control
Cont-0
Tx, Rx
Control
+4h
Xon-1 Word
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+5h
Xon-2 Word
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
+6h
Xoff-1 Word
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+7h
Xoff-2 Word (*1)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
(*1)As the COM-4(LPCI)H uses "+7h (I/O base address + 1Fh) of channel 4" as an interrupt vector register, it can use the xoff-2 word of channel
4. As the COM-8C-LPCI uses "+7h (I/O base address + 1Fh) of channel 4" and "+7h (I/O base address + 3Fh) of channel 8" as an interrupt
vector register, it can use the xoff-2 word of channel 4 and channel 8.
- Input Port 4 (Interrupt vector register)
The interrupt vector register of channel 1 - 4 uses "the I/O base address + 1Fh" and that of channel 5 - 8 uses "the
I/O base address + 3Fh"
I/O Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+1Fh
Interrupt vector register 1
Global
interrupt
(Reserved)
CH4
interrupt
CH3
interrupt
CH2
interrupt
CH1
interrupt
+3Fh
Interrupt vector register 2
(Reserved)
CH8
interrupt
CH7
interrupt
CH6
interrupt
CH5
interrupt
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
6/9
August 31, 2017
- Output Port 1 (General Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
Transmit Holding Register (THR)
Data Bit 7
Data Bit 6
Data Bit 5
Data Bit 4
Data Bit 3
Data Bit 2
Data Bit 1
Data Bit 0
+1h
Interrupt Enable Register (IER)
CTS
Interrupt
(*2)
RTS
Interrupt
(*2)
Xoff
Interrupt
(*2)
Sleep
Mode
(*2)
MODEM
Status
Interrupt
Receive
Line
Status
Interrupt
Transmit
Holding
Register
Receive
Holding
Register
+2h
FIFO Control Register (FCR)
RCVR
Trigger
(MSB)
RCVR
Trigger
(LSB)
TX
Trigger
(MSB)
TX
Trigger
(LSB)
DMA
Mode
Select
XMIT
FIFO
Reset
RCVR
FIFO
Reset
FIFO
Enable
+3h
Line Control Register (LCR)
Divisor
Latch
Enable
Set
Break
Set
Parity
Even
Parity
Parity
Enable
Stop
Bits
Word
Length
Bit 1
Word
Length
Bit 0
+4h
Modem Control Register (MCR)
Clock
Prescaler
Select
(*2)
IR
Mode
Enable
(*2)
Xon
Any
(*2)
Loop
Back
Enable
-OP2 and
INT
Enable
Out 1
0:INT
Enable
1:INT
Disable
(*1)
-RTS
-DTR
+5h
(Not Available)
+6h
(Not Available)
+7h
Scratch Pad Register (SPR) (*4)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+7h
Enhanced Mode Select Registers (EMSR) (*3) (*4)
Reserved
Reserved
RTS Hyst
Bit 3
RTS Hyst
Bit 2
Reserved
Reserved
Alt.RX/TX
FIFO Count
RX/TX
FIFO Count
(*1)For details, see the method of using interrupts.
(*2)This bit is enabled when EFR bit 4 is 1.
(*3)This register is enabled when FCTR bit 6 is 1.
(*4)As the COM-4(LPCI)H uses "+7h (I/O base address + 1Fh) of channel 4" as an interrupt vector register, it can use neither the scratch pad
register nor the enhanced mode select registers of channel 4.
As the COM-8C-LPCI uses "+7h (I/O base address + 1Fh) of channel 4" and "+7h (I/O base address + 3Fh) of channel 8"as an interrupt vector
register, it can use neither the scratch pad register nor the enhanced mode select registers of channel 4 and channel 8.
- Output Port 2 (Baud Rate Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
LSB of Divisor Latch (DLL)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+1h
MSB of Divisor Latch (DLM)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
7/9
August 31, 2017
- Output Port 3 (Enhanced Registers)
CH Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+0h
Trigger Level / FIFO Data Count Register
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
Trig/FC
+1h
Feature Control Register (FCTR)
Rx/Tx
Mode
SCPAD
Swap
Trig
Bit 1
Trig
Bit 0
RS485
Auto
Control
IrRx
In v.
-RTS
Delay
Bit 1
-RTS
Delay
Bit 0
+2h
Enhanced Feature Register (EFR)
Auto
-CTS
Auto
-RTS
Special
Char,
Select
Enable
IER
Bits 4 - 7,
ISR, FCR
Bits 4 - 5,
MCR
Bits 5 - 7
Cont-3
Tx, Rx
Control
Cont-2
Tx, Rx
Control
Cont-1
Tx, Rx
Control
Cont-0
Tx, Rx
Control
+4h
Xon-1 Word
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+5h
Xon-2 Word
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
+6h
Xoff-1 Word
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
+7h
Xoff-2 Word (*1)
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
(*1)As the COM-4(LPCI)H uses "+7h (I/O base address + 1Fh) of channel 4" as an interrupt vector register, it can use the xoff-2 word of channel
4. As the COM-8C-LPCI uses "+7h (I/O base address + 1Fh) of channel 4"and "+7h (I/O base address + 3Fh) of channel 8" as an interrupt
vector register, it can use the xoff-2 word of channel 4 and channel 8.
- Output Port 4 (Interrupt Vector Register)
The interrupt vector register uses "the I/O base address + 1Fh" regardless of the channel used.
I/O Base
D7
D6
D5
D4
D3
D2
D1
D0
Address
+1Fh
Interrupt Vector Register
Global
interrupt
(Reserved)
Clock
selection
Bit
1
Clock
selection Bit
0
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
8/9
August 31, 2017
3.3. Interrupt Vector Register
* The COM-1(LPCI)H cannot use CH2 – CH8 interrupts.
The COM-2(LPCI)H cannot use CH3 – CH8 interrupts.
The COM-4(LPCI)H cannot use CH5 – CH8 interrupts.
+1Fh
D7
+1Fh
D7 D3 D2 D1 D0
D0D6 - D2
D6 - D4
D1
- Output port
- Input port
CH1 interrupt
0 : Occurred
1 : Not Occurred
Global interrupt
0 : Enable
1 : Disable
CH2 interrupt *
0 : Occurred
1 : Not Occurred
CH3 interrupt *
0 : Occurred
1 : Not Occurred
CH4 interrupt *
0 : Occurred
1 : Not Occurred
(Reserved)
(Reserved)
Clock selection
00 : Clock-0 mode (1.8432 MHz)
01 : Clock-1 mode (3.6864 MHz)
10 : Clock-2 mode (7.3728MHz)
11 : Clock-3 mode (14.7456 MHz)
Global interrupt
0 : Disable
1 : Enable
+3Fh
D3 D2 D1 D0
D7 - D4
CH5 interrupt *
0 : Occurred
1 : Not Occurred
CH6 interrupt *
0 : Occurred
1 : Not Occurred
CH7 interrupt *
0 : Occurred
1 : Not Occurred
CH8 interrupt *
0 : Occurred
1 : Not Occurred
(Reserved)
TECHNICAL REFERENCE < COM-1(LPCI)H, COM-2(LPCI)H, COM-4(LPCI)H, COM-8C-LPCI >
CONTEC CO., LTD.
9/9
August 31, 2017
4. Operation Procedure
4.1. Access to I/O Ports
For access to I/O ports, refer to the sample programs stored in \Pci\Dos\Samples on the bundled disk "Standard
COM Driver Software/Com Setup Disk."
4.2. Interrupt function
When this board is used, only one interrupt request line is accepted for an interrupt of any of the channels. When
an interrupt of each channel is generated, it is latched by the interrupt vector register (IVR). When an interrupt is
accepted, the interrupt service routine can identify the channel requesting the interrupt by reading the IVR. When
the interrupt service is completed, read the IVR again before leaving the interrupt service to check if any interrupt
has been pending.
The XR16C2850 contains a register to enable interrupts by itself and to identify the channel generating an interrupt.
For using the register, refer to the data sheet for the XR16C2850 supplied by Exar Corporation.
The board has also a global interrupt to select whether to activate the PCI bus and a selected IRQ line or not.
To use interrupts, enable both of the global interrupt and the interrupt of each channel. Use the D7 bit of the IVR
to enable the global interrupt and the D2 bit of the modem control register (MCR) to enable the interrupt of each
channel.
Global interrupt (Bit D7 of IVR) Write "0": Disable (when the power is turned on)
Write "1": Enable
Interrupt of each channel (Bit D2 of MCR) Write "0": Enable (when the power is turned on)
Write "1": Disable
Disable interrupts of any channel not to be used.
A-48-082
LYFN363
INTA#
CH1 INT
CH1 Bit D2 of MCR
Bit D7 of IVR (+1Fh port)
*COM-1(LPCI)H has one channel only.
COM-2(LPCI)H has two channels only.
COM-4(LPCI)H has four channels only.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Contec COM-4(LPCI)H Owner's manual

Contec
Brand
Contec
Model
COM-4(LPCI)H
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents