Wacker Neuson GS8.5V User manual

Brand: Wacker Neuson

Model: GS8.5V

Category: Power generators

Type: User manual

Wacker Neuson GS8.5V is a portable generator designed for providing backup power during emergencies or recreational activities. It's powered by a reliable engine and delivers 8.5kW of continuous power, making it suitable for running various electrical devices and tools. The GS8.5V features a user-friendly control panel with 240V receptacles, a main circuit breaker, and a GFCI for enhanced safety. It's equipped with an auto-idle function that adjusts the engine speed based on the load, saving fuel and reducing noise.

www.wackergroup.com

Generator

GS 8.5V

GS 9.7V

OPERATOR’S MANUAL

0154589en 006

0706

0154589EN

DANGER

CARBON MONOXIDE

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or

smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot

smell the exhaust, you could be breathing CO.

• NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed

areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or

opening windows and doors does NOT supply enough fresh air.

• ONLY use a generator outside and far away from windows, doors, and vents. These

openings can pull in generator exhaust.

Even when you use a generator correctly, CO may leak into the home. ALWAYS use a

battery-powered or battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh

air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.

GS 8.5V / GS 9.7V Table of Contents

wc_bo0154589en_006TOC.fm 1

1. Foreword 3

2. California Evaporative Emission Control Warranty Statement 4

3. Safety Information 6

3.1 Laws Pertaining to Spark Arresters ...................................................... 6

3.2 Operating Safety .................................................................................. 7

3.3 Operator Safety while using Internal Combustion Engines .................. 8

3.4 Service Safety ...................................................................................... 9

3.5 Label Locations .................................................................................. 10

3.6 Safety and Operating Labels .............................................................. 11

4. Technical Data 15

4.1 Generator ........................................................................................... 15

4.2 Engine ................................................................................................ 16

5. Operation 17

5.1 Application and Power Requirements ................................................ 17

5.2 Outdoor Installation ............................................................................ 18

5.3 Indoor Installation ............................................................................... 18

5.4 Generator Derating ............................................................................. 19

5.5 Grounding the Generator ................................................................... 20

5.6 Use of Extension Cords ...................................................................... 21

5.7 Recommended Battery ....................................................................... 21

5.8 Control Panel ...................................................................................... 22

5.9 240V Receptacles .............................................................................. 23

5.10 Main Circuit Breaker ........................................................................... 23

5.11 Ground Fault Circuit Interrupt (GFI) ................................................... 23

5.12 Engine Auto Idle ................................................................................. 24

5.13 Engine Speed ..................................................................................... 24

5.14 Before Starting ................................................................................... 25

5.15 To Run Generator .............................................................................. 25

5.16 To Stop ............................................................................................... 26

Table of Contents GS 8.5V / GS 9.7V

wc_bo0154589en_006TOC.fm 2

6. Maintenance 27

6.1 Engine Maintenance ............................................................................27

6.2 Periodic Maintenance Schedule ..........................................................27

6.3 Engine Lubrication ...............................................................................28

6.4 Oil Filter ...............................................................................................29

6.5 Air Cleaner ..........................................................................................30

6.6 Spark Plug ...........................................................................................31

6.7 Fuel Filter ............................................................................................32

6.8 Carburetor Adjustment ........................................................................33

6.9 Storage ................................................................................................34

6.10 Transporting ........................................................................................34

6.11 Troubleshooting ...................................................................................35

6.12 Wire Colors ..........................................................................................35

6.13 Generator Wiring Schematic ...............................................................36

6.14 Engine Wiring Diagram .......................................................................39

wc_tx000001gb.fm 3

CALIFORNIA

Proposition 65 Warning:

Engine exhaust, some of its constituents, and certain vehicle

components, contain or emit chemicals known to the State of

California to cause cancer and birth defects or other reproductive

harm.

1. Foreword

This manual provides information and procedures to safely operate

and maintain this Wacker model. For your own safety and protection

from injury, carefully read, understand and observe the safety

instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this

manual or need an additional copy, please contact Wacker

Corporation. This machine is built with user safety in mind; however,

it can present hazards if improperly operated and serviced. Follow

operating instructions carefully! If you have questions about operating

or servicing this equipment, please contact Wacker Corporation.

The information contained in this manual was based on machines in

production at the time of publication. Wacker Corporation reserves the

right to change any portion of this information without notice.

All rights, especially copying and distribution rights, are reserved.

No part of this publication may be reproduced in any form or by any

means, electronic or mechanical, including photocopying, without

express written permission from Wacker Corporation.

Any type of reproduction or distribution not authorized by Wacker

Corporation represents an infringement of valid copyrights and will be

prosecuted. We expressly reserve the right to make technical

modifications, even without due notice, which aim at improving our

machines or their safety standards.

WARNING

California Evaporative Emission Control Warranty Statement

wc_tx000572gb.fm 4

2. California Evaporative Emission Control Warranty Statement

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Wacker Corporation, Inc. are

pleased to explain the evaporative emission control system (EECS)

warranty on your model year 2006 and later portable generator. In

California, new portable generators must be designed, built and

equipped to meet the State’s stringent anti-smog standards. Wacker

Corporation must warrant the EECS on your portable generator for the

period of time listed below provided there has been no abuse, neglect

or improper maintenance of your portable generator.

Your EECS for the 2006 model year on your portable generator

includes the fuel line, fuel line clamps and fuel line fittings.

Where a warrantable condition exists, Wacker Corporation will repair

your portable generator at no cost to you including diagnosis, parts and

labor.

MANUFACTURER’S WARRANTY COVERAGE:

This EECS is warranted for two years from the initial date of purchase.

If any evaporative emission-related part on your equipment is

defective, the part will be repaired or replaced by Wacker Corporation

at no charge to you. The owner shall not be charged for diagnostic

labor that leads to determination that a warranted part is in fact

defective, provided that such diagnostic work is performed at a Wacker

Corporation’s authorized service center.

WARRANTY PERIOD:

Any warranted part that is not scheduled for replacement as required

maintenance, or which is scheduled only for regular inspection to the

effect of “repair or replace as necessary” shall be warranted for two

years. Any warranted part that is scheduled for replacement as

required maintenance shall be warranted for a time not less than the

remaining warranty period.

California Evaporative Emission Control Warranty Statement

wc_tx000572gb.fm 5

OWNER’S WARRANTY RESPONSIBILITIES:

As the portable generator owner, you are responsible for performance

of the required maintenance listed in your owner’s manual. Wacker

Corporation recommends that you retain all receipts covering

maintenance on your portable generator, but Wacker Corporation

cannot deny warranty solely for the lack of receipts.

As the portable generator owner, you should however be aware that

Wacker Corporation may deny you warranty coverage if your portable

generator or a part has failed due to abuse, neglect, or improper

maintenance or unapproved modifications.

You are responsible for presenting your portable generator to Wacker

Corporation’s authorized service center as soon as the problem exists.

The warranty repairs should be completed in a reasonable amount of

time, not to exceed 30 days. If you have a question regarding your

warranty coverage, you should contact your nearest authorized

Wacker service center or call 1-800-770-0957.

WHAT IS NOT COVERED:

All failures caused by abuse, neglect, or improper maintenance are not

covered. In addition, the use of add-on or modified parts will be

grounds for disallowing a warranty claim.

WARRANTED PARTS:

The repair or replacement of any warranted part otherwise eligible for

warranty coverage may be excluded from such warranty coverage if

Wacker Corporation demonstrates that the portable generator has

been abused, neglected, or improperly maintained, and that such

abuse, neglect, or improper maintenance was the direct cause of the

need for repair or replacement of the part. That notwithstanding, any

adjustment of a component that has a factory installed, and properly

operating, adjustment limiting device is still eligible for warranty

coverage. The following emission warranty parts list is covered:

(1)Fuel Line.

(2)Fuel Line Clamps.

(3)Fuel Line Fittings.

Safety Information GS 8.5V / GS 9.7V

wc_si000057gb.fm 6

3. Safety Information

This manual contains DANGER, WARNING, CAUTION, and NOTE

callouts which must be followed to reduce the possibility of personal

injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol, CAUTION indicates

a potentially hazardous situation which, if not avoided, may result in

property damage.

Note: Contains additional information important to a procedure.

3.1 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codes

specify that in certain locations spark arresters be used on internal

combustion engines that use hydrocarbon fuels. A spark arrester is a

device designed to prevent accidental discharge of sparks or flames

from the engine exhaust. Spark arresters are qualified and rated by

the United States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult

the engine distributor or the local Health and Safety Administrator.

DANGER

WARNING

CAUTION

GS 8.5V / GS 9.7V Safety Information

wc_si000057gb.fm 7

3.2 Operating Safety

BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER

DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR

DEATH TO UTILITY WORKERS!

Improper connection of generator to a building's electrical system can

allow electrical current from the generator to backfeed into utility lines.

This may result in electrocution of utility workers, fire, or explosion.

Connections to a building's electrical system must be made by a

qualified electrician and comply with all applicable laws and electrical

codes.

If connected to a building's electrical system the generator must meet

the power, voltage, and frequency requirements of the equipment in

the building. Differences in power, voltage, and frequency

requirements may exist and improper connection may lead to

equipment damage, fire, and personal injury or death.

Familiarity and proper training are required for the safe operation of

equipment. Equipment operated improperly or by untrained personnel

can be dangerous. Read the operating instructions contained in both

this manual and the engine manual and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the equipment before

being allowed to operate the machine.

3.2.1 NEVER operate the generator when open containers of fuel, paint, or

other flammable liquids are near.

3.2.2 NEVER operate the generator, or tools attached to the generator, with

wet hands.

3.2.3 NEVER use worn electrical cords. Severe electrical shock and

equipment damage may result.

3.2.4 NEVER run the electrical cords under the generator, or over vibrating

or hot parts.

3.2.5 NEVER enclose or cover the generator when it is in use or when it is

hot.

3.2.6 NEVER overload the generator. The total amperage of the tools and

equipment attached to the generator must not exceed the load rating

of the generator.

3.2.7 NEVER operate the machine in snow, rain, or standing water.

3.2.8 NEVER allow untrained personnel to operate or service the generator.

The generator set should be set up by a trained electrician.

3.2.9 ALWAYS store the equipment properly when it is not being used.

Equipment should be stored in a clean, dry location out of the reach of

children.

DANGER

WARNING

Safety Information GS 8.5V / GS 9.7V

wc_si000057gb.fm 8

3.2.10 ALWAYS be sure the machine is on a firm, level surface and will not

tip, roll, slide, or fall while operating.

3.2.11 ALWAYS transport the generator in an upright position.

3.2.12 ALWAYS keep the machine at least one meter (three feet) away from

structures, buildings, and other equipment during use.

3.2.13 ALWAYS keep the area immediately surrounding and underneath the

machine clean, neat, and free of debris and combustible materials.

Make sure that the area overhead is clear of debris that could fall onto

or into the machine or exhaust compartment.

3.2.14 ALWAYS remove all tools, cords, and other loose items from the

generator before starting it.

3.2.15 ALWAYS make certain the machine is well-grounded and securely

fastened to a good earthen ground per national and local regulations.

3.3 Operator Safety while using Internal Combustion Engines

Internal combustion engines present special hazards during operation

and fueling. Read and follow the warning instructions in the engine

owner’s manual and the safety guidelines below. Failure to follow the

warnings and safety guidelines could result in severe injury or death.

3.3.1 DO NOT run the machine indoors or in an enclosed area such as a

deep trench unless adequate ventilation, through such items as

exhaust fans or hoses, is provided. Exhaust gas from the engine

contains poisonous carbon monoxide gas; exposure to carbon

monoxide can cause loss of consciousness and may lead to death.

3.3.2 DO NOT smoke while operating the machine.

3.3.3 DO NOT smoke when refueling the engine.

3.3.4 DO NOT refuel a hot or running engine.

3.3.5 DO NOT refuel the engine near an open flame.

3.3.6 DO NOT spill fuel when refueling the engine.

3.3.7 DO NOT run the engine near open flames.

3.3.8 DO NOT start the engine if fuel has spilled or a fuel odor is present.

Move the generator away from the spill and wipe the generator dry

before starting.

3.3.9 ALWAYS refill the fuel tank in a well-ventilated area.

3.3.10 ALWAYS replace the fuel tank cap after refueling.

3.3.11 ALWAYS check the fuel lines and the fuel tank for leaks and cracks

before starting the engine. Do not run the machine if fuel leaks are

present or the fuel lines are loose.

DANGER

GS 8.5V / GS 9.7V Safety Information

wc_si000057gb.fm 9

3.4 Service Safety

Poorly maintained equipment can become a safety hazard! In order

for the equipment to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary. If

the generator is experiencing problems or is being serviced, attach a

“DO NOT START” sign to the control panel to notify other people of its

condition.

3.4.1 DO NOT use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

3.4.2 DO NOT attempt to clean or service the machine while it is running.

3.4.3 DO NOT modify the equipment without the express written approval of

the manufacturer.

3.4.4 DO NOT allow water to accumulate around the base of the machine.

If water is present, move the machine and allow the machine to dry

before servicing.

3.4.5 DO NOT service the machine if your clothing or skin is wet.

3.4.6 DO NOT allow untrained personnel to service this equipment. Only

trained electrical technicians should be allowed to service the electrical

components of this equipment.

3.4.7 ALWAYS keep the machine clean and labels legible. Replace all

missing and hard-to-read labels. Labels provide important operating

instructions and warn of dangers and hazards.

3.4.8 ALWAYS replace the safety devices and guards after repairs and

maintenance.

3.4.9 ALWAYS let the engine cool before transporting or servicing it.

3.4.10 ALWAYS keep hands, feet, and loose clothing away from the moving

parts on the generator and engine.

3.4.11 ALWAYS turn the engine off before servicing the machine. If the

engine has electric start, disconnect the negative terminal on the

battery before servicing the machine.

3.4.12 ALWAYS keep the fuel lines in good condition and properly connected.

Leaking fuel and fumes are extremely explosive.

WARNING

Safety Information GS 8.5V / GS 9.7V

wc_si000057gb.fm 10

3.5 Label Locations

GND

88897

DANGER

GEFAHR

DANGER

PELIGRO

STOP

GS 8.5V / GS 9.7V Safety Information

wc_si000057gb.fm 11

3.6 Safety and Operating Labels

Wacker machines use international pictorial labels where needed.

These labels are described below:

Label Meaning

DANGER!

Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operator’s

Manual.

No sparks, flames, or burning objects near the machine. Shut off the engine before refu-

eling.

WARNING!

Hot surface!

CAUTION!

Read and understand the supplied Operator’s

Manuals before operating this machine. Fail-

ure to do so increases the risk of injury to your-

self or others.

CAUTION!

Lifting point

Electrical ground

DANGER

GEFAHR

DANGER

PELIGRO

STOP

GND

88897

Safety Information GS 8.5V / GS 9.7V

wc_si000057gb.fm 12

Neutral bonded to frame.

Key switch:

off

start

Open main circuit breaker.

Open the fuel flow valve.

Open the choke.

Turn engine key switch to “ON” position.

Label Meaning

1 2

GS 8.5V / GS 9.7V Safety Information

wc_si000057gb.fm 13

Pull rewind starter or turn engine key switch to

crank starter.

Close main circuit breaker.

Close the fuel flow valve.

Close the choke.

Turn engine key switch to “OFF” position.

Important Emissions Information

This equipment meets California EVP

emission regulations for small off-road

engines.

Label Meaning

Safety Information GS 8.5V / GS 9.7V

wc_si000057gb.fm 14

A nameplate listing the model number, item

number, revision number, and serial number is

attached to each unit. Please record the infor-

mation found on this plate so it will be available

should the nameplate become lost or dam-

aged. When ordering parts or requesting ser-

vice information, you will always be asked to

specify the model number, item number, revi-

sion number, and serial number of the unit.

This machine may be covered by one or more

patents.

Label Meaning

M E N O M O N E E F A L L S , W I U S A 5 3 0 5 1

M o d e l

S e r i a l N o .

k W m a x

I t e m N o .

k g

l b s

R e v .

P . F .

h z

M A D E I N U S A

1 1 0 9 9 2

GS 8.5V / GS 9.7V Technical Data

wc_td000057gb.fm 15

4. Technical Data

4.1 Generator

Item No. GS 8.5V

0007661

GS 9.7V

0007662

Generator

Maximum Output

kW / kVA

8.5 / 8.5 9.7 / 9.7

Continuous Output

8.2 9.3

Type Dual voltage, single phase,

brush-type system

AC Voltages Available

volts

phase

120 / 240

1ø

Frequency

Power Factor 1.0

AC receptacles:

120V GFI duplex

120V twist lock

240V twist lock

120/240V twist lock

amp

Continuous Current

at 120V

amp

68 77.5

L x W x H

mm (in.)

800 x 635 x 603 (31.5 x 25 x 23.75)

Weight (dry)

Kg (lbs.)

97 (214) 99 (218)

Technical Data GS 8.5V / GS 9.7V

wc_td000057gb.fm 16

4.2 Engine

Item No. GS 8.5V

0007661

Rev 116

and lower

GS 8.5V

0007661

Rev 117

and higher

GS 9.7V

0007662

Rev 117

and lower

GS 9.7V

0007662

Rev 118

and higher

Engine

Engine Type 2 cylinder, 4-cycle,

air-cooled, gasoline engine

Engine Make Briggs and Stratton

Engine Model

Vanguard

303447

Vanguard

350447

Vanguard

350447

Vanguard

356447

Rated Power

kW (Hp)

11.9 (16) 13.4 (18)

Displacement

(in

)

480 (29.3) 570 (34.75)

Spark Plug Champion RC12YC

Electrode Gap

mm (in.)

0.76 (0.030)

Starter

type / V

Electric / 12

Alternator

amp

Engine Speed - full load

rpm

3600

Auto Idle Speed

rpm

2200

Valve Clearance (cold)

mm (in.)

0.10–0.16 (0.004–0.006)

Air Cleaner

type

Dual element

Battery

V/size/CCA

12 / 22NF / 230

Engine Lubrication

oil grade

service class

SAE 10W30

SG, SF, or SE

Engine Oil Capacity

l (qts.)

1.6 (1.7)

Fuel

type

Regular unleaded gasoline

Fuel Tank Capacity

l (gal.)

28 (7.4)

Fuel Consumption

l (gal.)/hr.

5.03 (1.33) 6.21 (1.64)

GS 8.5V / GS 9.7V Operation

wc_tx000151gb.fm 17

5. Operation

5.1 Application and Power Requirements

This generator is designed to operate single-phase, 60 Hz appliances

running at 120 and 240 VAC. Both 120VAC and 240VAC power are

available at all times—there is no voltage selector switch.

CAUTION: Do not exceed the continuous rated output of the

generator—8.2 kilowatts for the GS 8.5V and 9.3 kilowatts for the

GS 9.7V. Damage to tools or generator will occur.

Check the nameplate or label provided on tools and appliances to

make sure their power requirements are met by the power output of the

generator. If the wattage is not given for a particular tool or appliance,

contact the tool manufacturer for wattage requirements.

Some appliances and tools require a surge of current when starting.

This means that the amount of power needed to initially start the

equipment is larger than the power required to keep it running. The

generator must be capable of supplying this "surge" current. Other

types of appliances require more power than is actually stated on their

nameplate.

The information in “Approximate Starting Power Requirements” is

offered only as a general guideline to help you determine power

requirements for different types of equipment. Check with your nearest

Wacker dealer, or contact the manufacturer or dealer of the tool or

appliance, if you have questions regarding power requirements.

CAUTION: Do not exceed the rated current limit of any receptacle.

CAUTION: If a tool or appliance does not reach full speed within a few

seconds when switched on, turn it off immediately to avoid damage.

Approximate Starting Power Requirements

• Incandescent lights and appliances such as irons and hot plates,

which use a resistive-type heating element, require the same wattage

to start and run as is stated on their nameplates.

• Fluorescent and mercury lamps require 1.2–2 times their stated watt-

age to start.

• Electrical motors and many types of electrical tools often require a

large starting current. The amount of starting current depends on the

type of motor and its use.

• Most electrical tools require 1.2–3 times their stated wattage for start-

ing.

• Loads such as submersible pumps and air compressors require a

very large force to start. They need as much as 3–5 times the wattage

stated on the nameplate in order to start.

Operation GS 8.5V / GS 9.7V

wc_tx000151gb.fm 18

If the wattage is not given for a particular tool or appliance, it can be

calculated by multiplying its voltage and amperage requirements:

Single Phase: VOLTS x AMPS = WATTS

Three Phase: VOLTS x AMPS x 1.732 x 0.8 = WATTS

5.2 Outdoor Installation

Place the generator in an area where it will not be exposed to rain,

snow, or direct sunlight. Make sure it is positioned on firm, level

ground, so it will not slide or shift. Position the engine exhaust away

from areas where people may be present.

If operating the generator inside a tunnel or deep trench, make sure

there is adequate ventilation. Precautions similar to those required

when operating indoors may be necessary.

The surrounding area must be free from water and moisture. All

components must be protected from excessive moisture.

5.3 Indoor Installation

If the generator must be installed indoors, adequate ventilation or

exhaust hoses must be provided. When venting exhaust fumes, make

sure the exhaust piping is large enough to prevent excessive back

pressure to the engine. Back pressure reduces engine efficiency and

may cause the engine to overheat.

Exhaust gas from the engine contains poisonous carbon monoxide

gas; exposure to carbon monoxide can cause loss of consciousness

and may lead to death. Never run the generator indoors or in an

enclosed area unless adequate ventilation, through such items as

exhaust hoses or fans, is provided.

When installed indoors, steps to prevent fire and explosion such as

providing a good, earthen ground, removing all flammable materials

near the generator, and using only electrical cables in good condition,

must be observed. See Operating Safety.

DANGER

Page is loading ...

Wacker Neuson GS8.5V User manual

Brand: Wacker Neuson

Model: GS8.5V

Category: Power generators

Type: User manual

Download PDF

report

Wacker Neuson GS8.5V User manual

Wacker Neuson GS8.5V User manual

Related papers

Other documents