ENG
FR
ESP
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 1
8
7
5
6
3
2
1
17
4
9
16
10
11
14
13
12
15
12
11
9
NG
R
SP
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 2
fig.1 fig.2 fig.3 fig.4
fig.5 fig.6 fig.7 fig.8
fig.9 fig.10 fig.11 fig.12
fig.13 fig.14 fig.15 fig.16
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 3
4
IMPORTANT SAFEGUARDS
Read all instructions before using the iron.
When using your iron, basic safety precautions should always be followed, including the
following:
11.1Use iron only for its intended use.
12.1To protect against a risk of electric shock, do not immerse the iron or the base of the iron in
water or other liquids.
13.1The iron should always be turned OFF before plugging or unplugging from outlet. Never
yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
14.1Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop
cord loosely around iron when storing.
15.1Always disconnect iron from electrical outlet when filling with water or emptying and when
not in use.
16.1Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To
avoid the risk of electric shock, do not disassemble the iron. Contact our Consumer Service
Department for examination, repair or adjustment. Incorrect reassembly can cause a risk of
electric shock when the iron is used.
17.1Close supervision is necessary for any appliance being used by or near children. Do not
leave iron unattended while connected or on an ironing board.
18.1Burns can occur from touching hot metal parts, hot water or steam. Use caution when you
turn a steam iron upside down - there may be hot water in the reservoir.
19.1This appliance is only for domestic and personal use.
SPECIAL INSTRUCTIONS
11.1To avoid a circuit overload, do not operate another high-wattage appliance on the same
circuit.
12.1If an extension cord is absolutely necessary, a 13 ampere cord should be used. Cords rated
for less amperage may overheat. Care should be taken to arrange the cord so that it cannot
be pulled or tripped over.
SAVE THESE INSTRUCTIONS
For your safety
1• This appliance complies with the technical rules and standards for safety currently in force
(Electromagnetic Compatibility, Low Voltage, Environment).
1• This appliance is not designed to be used by children and people with a physical, sensory
or mental impairment, or people without knowledge or experience, unless they are
supervised or given prior instructions concerning the use of the appliance by someone
responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
1• Warning ! The voltage of your electrical outlet must correspond to that of the iron (120V).
Connecting to the wrong voltage may cause irreversible damage to the iron and will
invalidate the guarantee.
1• If the electrical cord becomes damaged, it must be immediately replaced by an approved
Service Center to avoid any danger.
1• The appliance should not be used if it has fallen, if it has obvious damage, if it leaks or has
functional irregularities. Never dismantle your appliance; have it inspected by an approved
Service Center to avoid any danger.
1• Always unplug your appliance before filling or rinsing the reservoir, before cleaning it and
after each use.1
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 4
5
Description
1. Spray nozzle
2. Anti-scale valve
3. Steam control
4. Spray Button
5. Steam Button
6. Auto-Stop safety warning light
(depending on model)
7. Ergonomic grip (depending on model)
8. Electric power cord
9. Lock-System ring to open and close the
Ultracord system (depending on model)
10. Ultracord System (depending on model)
11. Water tank opening button
12. Water tank filler flap
13. Integral anti-scale system
(depending on model)
14. Thermostat indicator light
Goes out when the temperature has been
reached
15. Thermostat control
for choosing the ironing temperature
16. Extra Stable heel
17. Soleplate
Before first use
• Before using your iron with the steam function for the first time, we
recommend that you operate it in a horizontal position for a few
moments, away from your linen. Under the same conditions, press the
Steam button a few times.
• During the first few uses, a harmless odour and smoke may be given
off. This has no effect on the use of the iron and will disappear quickly.
Preparation
What water to use ?
• Your appliance has been designed to operate using untreated tap
water. However, it is necessary to operate the Self-Clean function
regularly in order to eliminate hard water deposits from the steam
chamber.
• Heat concentrates the elements contained in water during
evaporation. The types of water listed below contain organic waste or
mineral elements that can cause spitting, brown staining, or
premature wear of the appliance: water from clothes dryers, scented
or softened water, water from refrigerators, air conditioners, pure
distilled or demineralised water or rain water should not be used in
your T-Fal iron.
Please read these
instructions
carefully. Remove
any labels from the
soleplate before
heating up the iron.
If your water is very
hard, it is possible to
mix tap water
with store-bought
distilled or
demineralised water
in the following
proportions:
- 50% tap water,
- 50% distilled or
demineralised water.
ENG
• Never leave the appliance unattended when it is plugged in or during approximately 60
minutes that the soleplate remains hot.
• Your appliance gives off steam, which may cause burns, especially when you are ironing on
a corner of your ironing board. Never direct the steam toward people or animals.
• Your iron should be used and placed on a stable surface. When you put your iron onto its
heel or the iron rest, make sure that the surface on which you put it is stable.
• Any inappropriate use or use contrary to these instructions releases the brand from all
responsibility and renders the guarantee invalid.
Environment protection first !
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 5
6
Hold the iron a few
centimetres from the
fabric to avoid
burning delicate
fabrics.
Filling the water tank
• Check that the Ultracord system is properly locked.
• Unplug your iron before filling it.
• Set the steam control to “0” – fig.1.
• Take the iron with one hand and tilt it slightly, with the nose of the
soleplate pointing down.
• To open the flap of the water tank, push the button – fig.2.
• Fill the tank up to the “MAX” line – fig.3.
• Close the flap of the water tank, until it clicks into place.
Use
Adjust the temperature and the steam
• Set the thermostat control – fig.4, referring to the table below.
• The thermostat light comes on. It will go out when the soleplate is hot enough – fig.5.
RECOMMENDATIONS
• Your iron heats up quickly: so begin by ironing fabrics that are ironed
at low temperatures first, then go on to those requiring a higher
temperature,
• If you turn down the thermostat, wait until the thermostat light
comes back on before beginning to iron again,
• When ironing fabrics with mixed fibres, set the ironing temperature for
the most delicate fibre. For delicate fabrics we recommend testing the
fabric first on an inconspicious place eg (inside the hem).
Spray Function
• Whether steam or dry ironing, you are able to use the spray button to
dampen laundry to remove stubborn creases – fig.6.
Obtain more steam
• Press the Steam button from time to time – fig.7.
• Wait a few seconds between each shot before pressing the Steam
button again.
Vertical steam ironing
• Hang the garment on a hanger and hold the fabric slightly pulled
straight with one hand.The steam is very hot, so you should always do
this with the garment on a hanger – never iron clothes which someone
is wearing.
• Set the thermostat control to “MAX” – fig.8.
• Press the Steam button repeatedly – fig.7 moving the iron from
top to bottom – fig.9, wait a couple of seconds between each use of
the button.
FABRIC
POSITION OF
THERMOSTAT CURSOR
STEAM SETTING
POSITION
LINEN
COTTON
WOOL
SILK
SYNTHETIC
(Polyester, Acetate,
Acrylic, Nylon)
MAX
•••
••
•
0
Fill the tank up to
the “MAX”.
Never fill the
appliance by
holding it directly
under the tap.
= STEAM ZONE
In order to avoid
water dripping from
the iron onto the
linen:
- Turn off the steam
when ironing silk or
synthetic fabrics.
- Set it at the
minimum position for
wool.
Make sure that
there is water in the
tank before using
this button.
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 6
7
ENG
Dry ironing
• Set the temperature for the fabric to be ironed.
• Set the steam control to “0” – fig.1.
• You may start ironing when the thermostat light goes out.
Extra Functions
Ultracord System (depending on model)
Your iron has been designed with the Ultracord system to prevent the steam
cord from dragging across the linen and creasing it while ironing. It also
allows you to handle the iron more easily. To use the Ultracord system:
• Turn the Lock-System ring and put the indicator on the position –
fig.10.
• The Ultracord system opens out automatically. You can now plug in
your appliance and begin to iron.
• Each time you put your iron on its heel, the Ultracord system closes
automatically and opens out each time you pick the iron up again.
Integral anti-scale system (depending on model)
Your iron is equipped with an integral anti-scale system – fig.11. This
system will help to provide:
• a better ironing quality with a constant flow of steam,
• lasting performance from your appliance.
Auto-Stop safety feature (depending on model)
• The electronic system cuts off the electric power and the Auto-Stop
warning light flashes if the iron is left vertically on its heel for more than
8 minutes, or in a horizontal position for more than 30 seconds – fig.12.
• To restart the iron, just move it gently until the warning light stops
flashing.
Anti-drip function (depending on model)
• If the soleplate temperature is too low, the iron will not produce steam
because of the anti-drip technology which prevents droplets of water
leaking from the soleplate.
Maintenance and cleaning
Cleaning the anti-scale valve (once a month)
• Unplug your iron and empty the water tank.
• To remove the anti-scale valve, pull it up – fig.13.
• Soak the valve in a cup of white spirit vinegar or plain lemon juice for
hours – fig.14.
• Rinse the valve under running water.
• Replace the anti-scale valve.
Self-cleaning
• Fill the tank of your iron with untreated tap water. Stand the iron on it’s
heel with the thermostat set to “Max” and heat it up.
• When the thermostat light goes out, unplug the iron and hold it in a
horizontal position, over a sink. Remove the anti-scale valve – fig.13.
• Shake the iron gently, over the sink, until some of the water in the water
tank (with the impurities) has flowed out through the soleplate – fig.15.
• At the end of the operation, push the anti-scale valve back into position.
• Unplug the iron, and when the soleplate is just warm, wipe it with a soft
cloth.
For easier use,
always use the
Ultracord system.
When the Auto-Stop
warning light is on, it
is normal for the
thermostat light to
remain off.
When using the iron
for the first time, allow
2 minutes for steam to
be produced.
Be careful !
- Never touch the
end of the valve.
- The iron will not
function without the
anti-scale valve.
The self-cleaning
function helps to slow
down scaling in your
iron.
In order to extend the
life of your iron, use
the Self-Cleaning
function once a
month.
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 7
Cleaning the soleplate
• While the soleplate is still slightly warm, clean it by wiping over it with
a damp non-metallic cloth.
Storing your iron
• Unplug the iron and wait for the soleplate to cool down.
• Close the Ultracord System and lock it by positionning the ring
indicator (depending on model) onto .
• Empty the water tank and set the steam control to “0”. A little water
may remain in the tank.
• Wind the cord around the heel at the back of the iron. Store the iron on
its heel – fig.16.
Never use abrasive or
aggressive products
on the soleplate.
If there is a problem
PROBLEM POSSIBLE CAUSES SOLUTIONS
Water drips from the
holes in the soleplate.
The chosen temperature is too
low and does not allow for the
formation of steam.
Position the thermostat in the steam range
(from •• to MAX).
You are using steam while the iron is
not hot enough.
Wait until the thermostat light goes out.
You are using the Steam button
too often.
Wait a few seconds between each use of the
Steam button.
There is too much steam. Reduce the steam.
You have stored the iron horizontally,
without emptying it and without
setting it to “0”.
See the section "Storing your iron".
Brown streaks come
through the holes in
the soleplate and
stain the linen.
You are using chemical descaling
agents.
Do not add any descaling agents to the water
in the water tank.
You are not using the right type of
water.
Perform a self-cleaning operation and
consult the section "What water to use?"
Fabric fibres have accumulated in the
holes of the soleplate and are burning.
Perform the self-cleaning operation and clean
the soleplate with a damp sponge. Vacuum
the holes of the soleplate from time to time.
The soleplate is dirty
or brown and can
stain the linen.
You are ironing with an inappropriate
setting (temperature too high).
Clean the soleplate as indicated above.
Select the appropriate setting.
Your linen has not been rinsed
sufficiently or you are using starch.
Clean the soleplate as indicated above.
Always spray starch onto the reverse side of
the fabric to be ironed.
There is little or no
steam.
The water tank is empty. Fill the water tank.
The anti-scale valve is dirty. Clean the anti-scale valve.
Your iron has a build-up of scale. Clean the anti-scale valve and carry out a self-
clean.
Your iron has been used dry for too long. Carry out a self-clean.
The soleplate is
scratched or
damaged.
You have placed your iron flat on a
metallic rest-plate or ironed over a zip.
Always set your iron on its heel.
Water is running out
of the water tank
flap.
You have not closed the water tank
flap properly.
Check that the water tank flap is locked
properly (until your hear a "click").
Steam or water
leak from the iron
as you finish filling
the tank.
The steam control is not set to the “0”
position.
Check that the steam control is set to the
“0” position.
The spray does not
spray.
There is not enough water in the water
tank.
Fill up the water tank.
8
For all other problems or questions, please contact our Consumer Service Department at 1-800-395-
8325 or visit us at www.t-falusa.com. Or in Canada at 1-800-418-3325 or visit our website at www.t-
fal.ca. You may also contact an approved Service Center, please visit our website for their contact
information.
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 8
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 20
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 21
1800110948
1800110948-AQUASPEED ULTRACORD USA CAN 24/09/07 15:18 Page 22
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: T-Fal Aquaspeed Manuel utilisateur
- español: T-Fal Aquaspeed Manual de usuario