Indesit IWDC 6145 (EU) User guide

GB

1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the washer-dryer and

starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Troubleshooting, 11

Service, 12

IWDC 6145

Instructions for use

WASHER-DRYER

English,1

GB

BG

Français,25

F

Česky,49

CZ

Nederlands,37

NL

Български,13

! This symbol reminds you to read this

instruction manual.

DE

Deutsch,61

2

GB

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not

been damaged during the transportation process.

If it has been damaged, contact the retailer and do

not proceed any further with the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the applian-

ce (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loo-

sening the adjustable

front feet (see figure);

the angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is ope-

rating. If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient venti-

lation space underneath the washing machine.

Connecting the electricity and wa-

ter supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a ¾ gas threaded con-

nection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is si-

tuated on the top right-

hand side of the rear

part of the appliance

(see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

GB

3

Technical data

Model

IWDC 6145

Dimen-

sions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 6 kg for the wash

programme;

from 1 to 5 kg for the drying

programme

Electrical

c o n n e c -

tions

please refer to the technical

data plate fixed to the machine

Water

connec-

tions

maximum pressure 1 MPa

(10 bar)

minimum pressure 0.05 MPa

(0.5 bar)

drum capacity 58 litres

Spin

speed

up to 1400 rotations per

minute

Energy

rated pro-

grammes

according

to regula-

tion

EN 50229

Wash: programme 2; tempe-

rature 60°C;

run with a load of 6 kg.

Drying: select the “Cotton”

drying programme and set the

drying level to “ ”, for both

loads. The first drying cycle

must be carried out with the

nominal load.

This appliance conforms to

the following EC Directives:

- EMC 2014/30/EU (Electro-

magnetic Compatibility)

- 2012/19/EU - (WEEE)

- LVD 2014/35/EU Low Vol-

tage)

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct supplied

to the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•the socketis earthed and complies with all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see opposite);

•thesocketiscompatiblewiththeplugofthe

washing machine. If this is not the case, repla-

ce the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been installed,

the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

4

GB

Care and maintenance

Cutting off the water and electri-

city supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system

inside the washing machine and help to pre-

vent leaks.

•Unplugthewashingmachinewhencleaning

it and during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

•Alwaysleavetheportholedoorajarinorder

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-clea-

ning pump which does not require any mainte-

nance. Sometimes, small items (such as coins

or buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdri-

ver, remove the cover

panel on the lower

front part of the wa-

shing machine (see

figure);

2. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

GB

5

Precautions and tips

! This Washer-dryer was designed and constructed in ac-

cordance with international safety regulations. The following

information is provided for safety reasons and must therefore

be read carefully.

General safety

• This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and know-

ledge if they have been given supervision or

instruction concerning use of the appliance

in a safe way and understand the hazards

involved. Children shall not play with the

appliance. Cleaning and user maintenance

shall not be made by children without super-

vision.

- Do not dry unwashed items in the tumble

dryer.

- Items that have been soiled with substan-

ces such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine,

waxes and wax removers should be washed

in hot water with an extra amount of deter-

gent before being dried in the tumble dryer.

- Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried

in the tumble dryer.

- Fabric softeners, or similar products,

should be used as specified by the fabric

softener instructions.

- The final part of a tumble dryer cycle

occurs without heat (cool down cycle) to

ensure that the items are left at a tempera-

ture that ensures that the items will not be

damaged.

WARNING:Neverstopatumbledryerbe-

fore the end of the drying cycle unless all

items are quickly removed and spread out

so that the heat is dissipated.

•Thisappliancewasdesignedfordomesticuseonly.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunplugging

the appliance from the electricity socket. Hold the plug

and pull.

•Donotopenthedetergentdispenserdrawerwhilethe

machine is in operation.

•Donottouchthedrainedwaterasitmayreachextreme-

ly high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethe

safety lock mechanism designed to prevent accidental

opening.

•Iftheappliancebreaksdown,donotunderanycircum-

stances access the internal mechanisms in an attempt

to repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupof

two or three people and handle it with the utmost care.

Never try to do this alone, because the appliance is very

heavy.

•BeforeloadinglaundryintotheWasher-dryer,makesure

the drum is empty.

• Duringthedryingphase,thedoortendstogetquitehot.

• Donotusetheappliancetodryclothesthat

have been washed with flammable solvents

(e.g. trichlorethylene).

• Donotusetheappliancetodryfoamrubber

or similar elastomers.

• Makesurethatthewatertapisturnedonduringthe

drying cycles.

• Childrenoflessthan3yearsshouldbekept

away from the appliance unless continuou-

sly supervised.

• Removeallobjectsfrompocketssuchas

lighters and matches.

Disposal

•Disposingofthepackagingmaterials:observelocal

regulations so that the packaging may be re-used.

• TheEuropeanDirective2012/19/EUonWasteElectrical

and Electronic Equipment, requires that old household

electrical appliances must not be disposed of in the

normal unsorted municipal waste stream. Old applian-

ces must be collected separately in order to optimise

the recovery and recycling of the materials they contain

and reduce the impact on human health and the envi-

ronment. The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when you

dispose of the appliance it must be separately collec-

ted. Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

6

GB

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the washer-dryer on and off.

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold

wash cycle (see “Personalisation”).

DRYING knob: used to set the desired drying programme

(see “Personalisation”).

WASH CYCLE PROGRESS/DELAY TIMER

indicator

light

s: used to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time remai-

ning until the wash cycle starts will be indicated (see next

page).

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tempo-

rarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this button;

the corresponding indicator light will flash orange, while the

indicator light for the current wash cycle phase will remain lit

in a fixed manner. If the DOOR LOCKED indicator light is

switched off, the door may be opened (wait approximately

3 minutes).

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after a few minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

Description of the washer-dryer

and starting a wash cycle

WASH CYCLE PROGRESS/

DELAY TIMER indicator lights

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

DRYING

knob

GB

7

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

IftheDELAYTIMERfunctionhasbeenactivated(see “Per-

sonalisation”), after the wash cycle has been started the

indicator light corresponding to the selected delay period

will begin to flash:

Astimepasses,theremainingdelaywillbedisplayedand

the corresponding indicator light will flash:

The set programme will start once the selected time delay

has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be-

gun, the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Note:whenthedryingcyclehasfinished,theDRYING

knob should be returned to the “0” position.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will

flash and only the second function will be activated; the

indicator light corresponding to the enabled option will

remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes). To open the door during a running wash cycle,

presstheSTART/PAUSEbutton;thedoormaybeopened

once the DOOR LOCKED indicator light turns off.

Starting a wash cycle

1. Switchthewasher-dryeronbypressingtheON/OFFbutton.Allindicatorlightswillswitchonforafewseconds,thenthey

willswitchoffandtheSTART/PAUSEindicatorlightwillpulse.

2. Load the laundry and close the door.

3.SettheWASHCYCLEknobtothedesiredprogramme.

4. Set the washing temperature (see “Personalisation”).

5. Set the drying cycle if necessary (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8.StartthewashcyclebypressingtheSTART/PAUSEbuttonandthecorrespondingindicatorlightwillremainlitinafixed

manner, in green.

Tocancelthesetwashcycle,pausethemachinebypressingtheSTART/PAUSEbuttonandselectanewcycle.

9.Attheendofthewashcyclethe indicator light will switch on. The door can be opened once the DOOR LOCKED

indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure

the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin/Drain

Drying

End of wash cycle

8

GB

Specials wash cycles

Sport Light (

wash cycle

9) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,

we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a

liquid detergent and dosage suitable for a half-load.

Sport Shoes (

wash cycle

10) is for washing sports shoes; for best results, do not wash more than 2 pairs (fabric)

simultaneously.

Express Wash & Dry (

wash cycle

13) was designed to wash and dry lightly soiled garments quickly. This cycle may

be used to wash and dry a laundry load of up to 0.5 kg in just 30 minutes.

To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.

Wash cycles

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water

temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

Table of wash cycles

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

duration

Prewash

Main

wash

Fabric

softener

Daily

1

Cotton with prewash: extremely soiled whites. 90° 1400

   

6 215’

2

Cotton: extremely soiled whites. 90° 1400



-

 

6 200’

2

Cotton (1): heavily soiled whites and resistant colours. 60° 1400



-

 

6 210’

2

Cotton (2): lightly soiled whites and delicate colours. 40° 1400



-

 

6 220’

3

Cotton: heavily soiled whites and resistant colours. 60° 1400



-

 

6 160’

4

Coloured Cotton: lightly soiled whites and delicate colours. 40° 1400



-

 

6 125’

5

Synthetics: lightly soiled resistant colours. 60° 1000



-

 

4,5 140’

Special

6

Wool: for wool, cashmere, etc. 40° 800 - -

 

2 90’

7

Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 - -

 

1 55’

8 Jeans

40° 800



-

 

4 80’

9 Sport Light

30° 600 - -

 

4 65’

10 Sport Shoes

30° 800 - -

 

Max. 2

pairs

50’

Drying

11 Cotton dry

- -



- - - 5 -

12 Synthetics dry

- -



- - - 4 -

13 Express Wash & Dry

30° 1400



-

 

0,5 30’

Partial wash cycles

Rinse - 1400



- -



6 50’

Spin - 1400



- - - 6 10’

Drain - 0 - - - - 6 3’

GB

9

Setting the temperature

TurntheTEMPERATUREknobtosetthewashtemperature(seeTable of wash cycles).

The temperature may be lowered, or even set to a cold wash . The washer-dryer will automatically prevent you from selec-

ting a temperature which is higher than the maximum value set for each wash cycle.

Setting the drying cycle

TurntheDRYINGknobtoselectthedesireddrying

option. There are two options:

A - Based on time: From 40 minutes to 180.

B - Based on the desired laundry dryness level:

Iron dry : suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

Hanger dry : ideal for clothes which do not need to

be dried fully.

Cupboard dry : suitable for laundry which can be put

back in a cupboard without being ironed.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table), perform the wash

cycle,andwhenthecycleiscomplete,dividethegarmentsintogroupsandputsomeofthembackinthedrum.Atthispoint,

follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the load.

Drying only

Use the cycle selector knob to select a drying cycle (11-12) in accordance with the type of fabric. The desired drying level or

timemayalsobesetusingtheDRYINGknob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note:

- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and

the function will not be activated.

- If the selected function is not compatible with another function which has been selected previously, the indicator light

corresponding to the first function selected will flash and only the second function will be activated; the indicator light

corresponding to the enabled option will remain lit.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled

cotton and synthetic fabrics (refer to the

“Table of wash cycles”

). “ ” enables you to wash in less time thereby saving

water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.

1400-600

Press this button to reduce the spin speed.

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours. Press the button repeatedly until the indicator light correspond-

ing to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled.

N.B.OncetheSTART/PAUSEbuttonhasbeenpressed,thedelaytimecanonlybemodifiedbydecreasingituntillaunching

the set programme.

Personalisation

Table of Drying times (guideline values)

Fabric

type

Load type

Max.

load (kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton

Clothing of diffe-

rent sizes, Terry

towels

5 255 230 180

Synthe-

tics

Sheets, Shirts, Py-

jamas, socks, etc.

4 180 130 115

10

GB

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

!Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

!Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-wash detergent (powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

•Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

•Emptyallgarmentpocketsandcheckthebuttons.

• Donot exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using programme

6, even those carrying the “hand-wash only” label. For

best results, use special detergents and do not exceed 2

kg of laundry.

Silk: use special wash cycle 7 to wash all silk garments.

We recommend the use of special detergent which has

been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or

mesh bag. Use wash cycle 7.

Jeans: Turn garments inside-out before washing and use

a liquid detergent. Use programme 8.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load

is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the

washer-dryer performs the distribution process instead of

spinning. To encourage improved load distribution and bal-

ance, we recommend small and large garments are mixed

in the load.

1

2

3

GB

11

Troubleshooting

Yourwasher-dryercouldfailtowork.BeforecontactingtheTechnicalAssistanceCentre(see “Assistance”), make sure that

the problem cannot be not solved easily using the following list.

Problem:

The Washer-dryer does not switch

on.

The wash cycle does not start.

The Washer-dryer does not take

in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The Washer-dryer continuously

takes in and

drains water.

The Washer-dryer does not drain or

spin.

The Washer-dryer vibrates a lot

during the spin cycle.

The Washer-dryer leaks.

The “Functions” indicator lights

and the “start/pause” indicator

light flash, while one of the “phase

in progress” indicator lights and

the “door locked” indicator light

will remain lit in a fixed manner.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.

•Thereisnopowerinthehouse.

•TheWasher-dryerdoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

• Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch the applian-

ceoffandcontacttheAssistanceService.Ifthedwellingisononeoftheupperfloorsof

a building, there may be problems relating to water drainage, causing the Washer-dryer

to fill with water and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

•Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain

phase to be started manually.

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•TheWasher-dryerisnotlevel(see “Installation”).

•TheWasher-dryeristrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

 Iftheproblempersists,contacttheTechnicalAssistanceService.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext

“for Washer-dryers” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• Theapplianceisnotpluggedintothesocket,ornotenoughtomakecontact.

• Therehasbeenapowerfailure.

• The appliance door is not shut properly.

• Adelayedstarthasbeenset.

• DRYINGknobisinthe0 position.

12

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

•Restarttheprogrammetocheckwhethertheproblemhasbeensolved;

•Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe

guarantee certificate.

! Alwaysrequesttheassistanceofauthorisedtechnicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of

the appliance by opening the door.

Page is loading ...

Indesit IWDC 6145 (EU) User guide

Indesit IWDC 6145 (EU) User guide

in other languages

Other documents