Makita CX401SYB User manual
- Category
- Battery chargers
- Type
- User manual
This manual is also suitable for
Page is loading ...
2
ENGLISH
Specifications
Model DC18SD
Input ........................................................................................................................................... A.C. 120 V 50 – 60 HZ
Output ...................................................................................................................................................D.C. 7.2 V – 18 V
Weight ...................................................................................................................................................0.59 kg (1.30 lbs)
• Manufacturer reserves the right to change specifications without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1. SAVE THESE INSTRUCTIONS — This manual contains
important safety and operating instructions for battery charger.
2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) bat-
tery, and (3) product using battery.
3. CAUTION — To reduce risk of injury, charge only MAKITA rechargeable batteries marked on the charger
label. Other types of batteries may burst causing personal injury and damage.
4. Non-rechargeable batteries cannot be charged with this battery charger.
5. Use a power source with the voltage specified on the nameplate of the charger.
6. Do not charge the battery cartridge in presence of flammable liquids or gases.
7. Do not expose charger to rain or snow.
8. Never carry charger by cord or yank it to disconnect from receptacle.
9. After charging or before attempting any maintenance or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever disconnecting charger.
10. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage
or stress.
11. Do not operate charger with damaged cord or plug. If the cord or plug is damaged, ask Makita authorized
service center to replace it in order to avoid a hazard.
12. Do not operate or disassemble charger if it has received a sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified serviceman. Incorrect use or reassembly may result in a risk of elec-
tric shock or fire.
13. The battery charger is not intended for use by young children or infirm persons without supervision.
14. Young children should be supervised to ensure that they do not play with the battery charger.
15. Do not charge battery cartridge when room temperature is BELOW 10°C (50°F) or ABOVE 40°C (104°F). At
the cold temperature, charging may not start.
16. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
17. Do not allow anything to cover or clog the charger vents.
FCC CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/ TV technician for help
3
Charging
1. Plug the battery charger into the proper AC voltage source. Charging light will flash in green color repeatedly.
2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger
can be opened with inserting and closed with pulling out the battery cartridge.
3. When the battery cartridge is inserted, the charging light color will change from green to red and charging will
begin. The charging light will keep lighting up lit steadily during charging. One red charging light indicates charged
condition in 0 – 80% and red and green ones indicate 80 – 100%.
4. With finish of charge, the charging lights will change from red and green ones to green one.
5. Charging time varies by temperature (10°C (50°F) – 40°C (104°F)) that battery cartridge is charged at and
conditions of the battery cartridge, such as a battery cartridge which is new or has not been used for a long period
of time.
6. After charging, remove the battery cartridge from charger and unplug the charger.
NOTE:
• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other
manufacturer’s batteries.
• When you charge a battery cartridge which is new or has not been used for a long period of time, it may not accept a
full charge until after discharging it completely and recharging a couple of times. (Ni-MH battery only)
• If charging light may flash in red color, battery condition is as below and charging may not start.
– Battery cartridge from just-operated tool or battery cartridge that has been left in a location exposed to direct sun-
light for a long time.
– Battery cartridge that has been left for a long time in a location exposed to cold air.
Charging will begin after the battery cartridge temperature reaches the degree at which charging is possible.
• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger
or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.
• DC18SD battery charger cannot use with INTERCHANGEABLE ADAPTER (ADP01, 04) and REFRESHING
ADAPTER (ADP02, 03).
Note:
• It may take longer than the above charging time because of the optimal charging selected according to the
temperature (10°C (50°F) – 40°C (104°F)), conditions of battery cartridge and maintenance charge.
Voltage 9.6 V 12 V 14.4 V
Capacity (Ah) Charging time (Minutes)
Number of cells 8 10 12
Ni-MH Battery cartridge
BH9020A — — 2.0 40
— BH1220C — 2.0 40
——— 2.7 55
BH9033A — — 3.3 70
— BH1233C — 3.3 70
Voltage 14.4 V 18 V 14.4 V 18 V
Charging time (Minutes)
Number of cells 4 5 8 10
Li-ion Battery cartridge
BL1415NA BL1815N — — 30
— BL1820B — — 45
——
BL1430/
BL1430B
BL1830/BL1830B 60
———BL1840B 90
———BL1850B 110
— — BL1460A BL1860B 130
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Makita CX401SYB User manual
- Category
- Battery chargers
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Makita CX401SYB Manuel utilisateur
- español: Makita CX401SYB Manual de usuario