AWSENS SL4002-WH User manual

  • Hello! I am an AI chatbot trained to assist you with the AWSENS SL4002-WH User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
© 2012 HeathCo LLC
TEST
Features
• Turnsonlightingwhenmotionisdetected.
• Automaticallyturnslightingoff.
• Photocellkeepsthelightingoffduringdaylighthours.
• LEDindicatesmotionwassensed(dayornight).
TEST 1 5 10
ON-TIME
Put the ON-TIME switch on the
bottomofthesensorintheTEST
position.
OPERATION
*resetstoAutoModeatdawn.
ON-TIME
TEST 1 5 10
...backon.
1Second
OFF then...
PuttheON-TIMEswitchinthe1,5,
or10minuteposition.
Manual mode only works at night
becausedaylightreturnsthesensor
toAUTO.
Flipthelightswitchoffforonesecond
thenbackontotogglebetweenAUTO
andMANUALMODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Note:Whenrstturnedonwaitabout1
1
/
2
minutesfor
thecircuitrytocalibrate.
Thispackageincludes:
LightControl
Requirements
• Thelightcontrolrequires120-voltsAC.
• IfyouwanttouseManualMode,thecontrolmustbe
wiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
• Thisproductisintendedforusewiththeenclosed
gasketandwithajunctionboxmarkedforuseinwet
locations.
Mode: On-Time Works: Day Night
Test
5Seconds x x
Auto
1,5,or10Minutes x
Manual
ToDawn* x
AUTO
MANUAL MODE
PlasticHanger
RubberPlug
Gasket
4Screws
(2sizesincluded)
MountingStrap
MountingBolt
2Wire
Connectors
Motion Activated Security Light
Model SL5462
2
204026-01
INSTALLATION
Foreasyinstallation,selectanexistinglightwithawall
switchforreplacement.
Forbestperformance,mountthextureabout8ft.(2.4m)
abovetheground.
NOTE:
Ifxtureismountedhigherthan
8ft.(2.4m),aimingthesensordownwillreducecoverage
distance.
Foreavemountonly:
Swingthesensorheadtowardstheclampscrew
joint.
If thesensorpops out oftheball joint, loosenthe
clampscrewandpushthesensorbackintotheball
joint.Tightentheclampscrewwhendone.
Thenrotatethesensorheadclockwise180°sothe
controlsfacedown.
Controls
Wall Mount Eave Mount
For under eave installation, the sensor head must
be rotatedasshowninthenexttwostepsforproper
operationandtoavoidtheriskofelectricalshock.
Controls
Controls
ClampScrew
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* Ifyougetconfusedwhileswitchingmodes,turnthe
poweroffforoneminute,thenbackon.Afterthecali-
brationtimethecontrolwillbeintheAUTOmode.
3
204026-01
1. Removetheexistinglightxture.
2. Installthemountingstrapasshownusingtwoscrews
thattyourjunctionbox.
3. Theplastichangercanbeusedtoholdthexture
whilewiring.Thesmallendoftheplastichanger
canbethreadedthroughtheholeinthecenterof
thecoverplate.Thesmallendthengoesintoone
oftheslotsonthemountingstrap.
4. Route the light control’s wires through the large
gasketholes.
5. Twistthejunctionboxwiresandxturewirestogether
asshown.Securewithwireconnectors.
Wire the Light Control
WARNING: Turn power off at circuit breaker
or fuse.
4
204026-01
180°
70ft.
(21m)
8ft.
(2.4m)
Maximum Range Maximum
Coverage Angle
NOTE:Ifxtureismountedhigherthan8ft.(2.4m),aim-
ingthesensordownwillreducecoveragedistance.
Thedetectorislesssensitivetomotiondirectlytowardsit.
3. Loosentheclampscrewinthe
sensor ball joint and gently
rotatethesensor.
4. Walk through the coverage
area noting where you are
whenthelightsturnon(also,
theLEDwillashseveraltimes
whenmotionisdetected).Move
thesensorheadup,down,or
sidewaystochangethecover-
agearea.Keep the sensor at
least 1" (25 mm) away from
the bulbs.
5. AdjusttheRANGEasneeded.
RANGE set too high may
increasefalsetriggering.
6. Secure the sensor head by
tightening the clamp screw.
Donotovertightenthescrew.
7. SettheamountofON-TIMEyouwantthelightsto
stayonaftermotionisdetected(1,5,or10minutes).
NOTE: It is recommended to use the10minute
ON-TIMEsettingwhenusingCFLbulbs.
Bottom of Sensor
Avoid aiming the control at:
•Objects that change temperature rapidly, such as
heating vents and air conditioners.These heat
sourcescouldcausefalsetriggering.
•Areaswherepets or trafficmaytriggerthecontrol.
•Nearby large, light-colored objectsreectinglight
maytriggertheshut-offfeature.Donotpointother
lightsatthesensor.
Clamp
Screw
Ball
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
Least Sensitive Most Sensitive
WARNING: Risk of fire. Do not aim the bulbs
at a combustible surface within 3 ft. (1 m).
TEST AND ADJUSTMENT
1. Turn on the circuit breaker and light switch.
NOTE: Sensor has a 1
1
/
2
minute warm up period
beforeitwilldetectmotion.Whenrstturned
on,wait1
1
/
2
minutes.
2. Turn the RANGE controltothe medium position
(halfwaybetweenMINandMAX)andtheON-TIME
controltotheTESTposition.
Motion Motion
Sensor
RANGE
1051TEST
ON-TIME
MIN MAX
IMPORTANT:DonotleaveON-TIMEswitchinthe
TESTposition.ThefrequentON/OFFcyclingofthe
bulbwillreduceitslife.
5
204026-01
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights will not come
on.
1. Lightswitchisturnedoff.
2. Floodlampislooseorburnedout.
3. Fuseisblownorcircuitbreakeristurnedoff.
4. Daylightturn-offisineffect.
5. Incorrectcircuitwiring,ifthisisanewinstallation.
6. Lightcontrolaimedinwrongdirection.
1. Turnlightswitchon.
2. Checkoodlampandreplaceifburnedout.
3. Replacefuseorturncircuitbreakeron.
4. Recheckafterdark.
5. Verifywiringiscorrect.
6. Re-aimlightcontroltocoverdesiredarea.
Lightscomeoninday-
light.
1. Light control may beinstalled in a relatively dark
location.
2. LightcontrolisinTEST.
1. Thextureisoperatingnormallyunderthesecondi-
tions.
2. Setcontrolswitchto1,5,or10minutes.
Lights come on for no
apparentreason.
1. Lightcontrolmaybesensingsmallanimalsorauto-
mobiletrafc.
2. Rangeissettoohigh.
1. Re-aimlightcontrol.
2. Reducerange.
Lightsturnofftoolatein
Dusk-to-Dawnsetting.
Lightcontrolmaybeinstalledinarelativelydarkloca-
tion.
Relocatelightcontrol,oruse3houror6hoursetting.
Lightsstayoncontinu-
ously.
1. Aoodlampispositionedtooclosetothelightcontrol
orpointedatnearbyobjectsthatcauseheattotrigger
thelightcontrol.
2. Thelightcontrolmaybepickingupaheatsource
likeanairvent,dryervent,orbrightlypainted,heat-
reectivesurface.
3. Lightcontrolisinmanualmode.
1. Repositiontheoodlampawayfromthelightcontrol
ornearbyobjects.
2. Reducerange.
3. SwitchlightcontroltoAUTO.
Lightsashonandoff. 1. Heatorlightfromtheoodlampsmaybeturningthe
lightcontrolonandoff.
2. Heatbeingreectedfromotherobjectsmaybeturn-
ingthelightcontrolonandoff.
3. LightcontrolisintheTESTmodeandwarmingup.
4. Lightmaybeleakingthroughtheoodlampreec-
tors.
1. Repositiontheoodlampawayfromthelightcon-
trol.
2. Repositionlightcontrol.
3. Flashingisnormalundertheseconditions.
4. ReplacetheoodlampswithnewhighqualityPAR
38lamps.(Makesurethemetallampprotectorsare
installed).
Lightsashonce,then
stay off in manual
mode.
Lightcontrolisdetectingitsownlights. Reposition ood lampsto keep area belowthe light
controlrelativelydark.
SPECIFICATIONS
TROUBLESHOOTING GUIDE
/