Fujitsu ASMG24CMCA Operating instructions

Brand: Fujitsu

Model: ASMG24CMCA

Type: Operating instructions

This manual is also suitable for

ASMG18CMCA

Fujitsu ASMG24CMCA is a wall-mounted air conditioner designed to provide cooling, with features like a human sensor for energy saving, a remote controller with a clock, a timer, and adjustable airflow direction. It uses the refrigerant R32, which is more environmentally friendly than traditional refrigerants. The unit is equipped with air filters to ensure clean and fresh air. It also has an economy mode for efficient operation.

En-1

AIR CONDITIONER

ASMG18CMCA

ASMG24CMCA

OPERATING MANUAL

Before using this product, read these instructions thoroughly and keep this manual for future reference.

Safety Precautions

To prevent personal injury, injury to others, or property damage, read this section carefully before you use this product, and be sure to comply to the

following safety precautions.

Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classied as follows:

WARNING CAUTION

This mark warns of death or serious injury. This mark warns of injury or damage to property.

This mark denotes an action that is PROHIBITED.

This mark denotes an action that is COMPULSORY.

• Explanation of symbols displayed on the indoor unit or outdoor unit.

WARNING

This symbol shows that this appliance uses a ammable refrigerant. If the refrigerant is leaked and exposure to an external

ignition source, there is a risk of re.

CAUTION

This symbol shows that the Operation Manual should be read carefully.

CAUTION

This symbol shows that a service personnel should be handling this equipment with reference to the Installation Manual.

CAUTION

This symbol shows that information is available such as the Operating Manual or Installation Manual.

WARNING

• The appliance shall be installed, operated and stored in a

room with a oor area larger than 2.06m

• The unit contains no user-serviceable parts. Always consult

authorized service personnel for repairing, installation, and

relocation of this product.

Improper installation or handling will cause leakage, electric

shock, or re.

• In the event of a malfunction such as burning smell,

immediately stop operation of the air conditioner, and

disconnect all the power supply by turning off the electrical

breaker or disconnecting the power supply cable. Then

consult authorized service personnel.

• Take care not to damage the power supply cable.

If it is damaged, it should only be replaced by authorized

service personnel.

• In the event of refrigerant leakage, be sure to keep away

from re or any ammables, and consult authorized service

personnel.

• If you see lightning or hear thunder, there might be a lightning

strike.

To prevent electric shock hazard, turn off the air conditioner

by using the remote controller, and do not touch the unit or

the power plug during thunderstorm.

• The appliance shall be stored in a room without continuously

operating ignition sources (for example: open ames, an

operating gas appliance or an operating electric heater).

• The appliance shall be stored in a well-ventilated area.

• Be aware that refrigerants may not contain an odour.

• The appliance shall be stored so as to prevent mechanical

damage from occurring.

• Disposing of the product shall be done properly, in

compliance with national or regional regulations.

• During transportation or relocation of the indoor unit, pipes

shall be covered with the wall hook bracket for protection.

Do not move the appliance by holding the indoor unit pipes.

(The stress applied to the pipe joints may cause the

ammable gas to leak during operation).

(continued)

Contents

Safety Precautions ..........................................................En-1

Indoor Unit Overview and Operations .............................En-3

Remote Controller Overview and Operations ..................En-4

Timer Operation...............................................................En-6

Human Sensor (Energy Saving) ......................................En-8

General Informations on Operation .................................En-8

Care and Cleaning...........................................................En-9

Troubleshooting ............................................................. En-10

R32

REFRIGERANT

This Air Conditioner contains and

operates with refrigerant R32.

THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED

BY QUALIFIED PERSONNEL.

Refer to Commonwealth, State, Territory and local legislation,

regulations, codes, installation & operation manuals, before

the installation, maintenance or service of this product.

(Cooling Only Model)

Wall Mounted Type

PART No. 9387081084

English

ไทย

OM_01_9387081084-EN.indd 1 4/6/2559 BE 3:51 PM

En-2

OPERATING MANUAL

WARNING

• Do not install the unit in area lled with mineral oil such as a

factory or area containing a large amount of splashed oil or

steam such as a kitchen.

• Do not start or stop the operation of this product by inserting

or pulling out the power plug, or by turning on or off the

circuit breaker.

• Do not use inammable gases near the unit.

• Do not expose yourself directly to the cooling airow for

many hours.

• Do not insert your ngers or any other objects into outlet

port, open panel, or intake grille.

• Do not operate with wet hands.

• Do not use means to accelerate the defrosting process or to

clean the appliance, other than those recommended by the

manufacturer.

• Do not pierce or burn.

CAUTION

• Provide occasional ventilation during use.

• Always operate the unit with air lters installed.

• Ensure that any electronic equipment is at least 1 meter

away from either the indoor unit or outdoor unit.

• Unplug the power supply cable when not using the indoor

unit for an extended period.

• After long period of use, check whether the installation stand

does not deteriorate to prevent the unit from falling down.

• The airow direction and the room temperature should be

carefully considered when you use this product in a room

with infants, children, elderly or sick persons.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not

play with the appliance.

• Do not direct the airow at replaces or heating apparatus.

• Do not block or cover the intake grille and the outlet port.

• Do not apply any heavy pressure to radiator ns.

• Do not climb on, place objects on, or hang objects from the unit

• Do not place vase or water container on the unit.

• Do not place any other electrical products or household

belongings under indoor unit or outdoor unit.

Dripping condensation from the unit might get them wet, and

may cause damage or malfunction of your property.

• Do not expose the unit directly to water.

• Do not use this product for preservation of food, plants,

animals, precision equipment, art work, or other objects. This

may cause quality deterioration of those items.

• Do not expose animals or plants to the direct airow.

• Do not drink the drainage from the air conditioner.

• Do not pull the power supply cable to disconnect the plug.

• Do not touch the aluminum ns of heat exchanger built-in

the indoor or outdoor unit to avoid personal injury when you

install or maintain the unit.

Safety Precautions (continued)

Indoor unit accessories

Remote

controller

Batteries Air cleaning lters Filter holders

Remote controller

holder

Tapping screws

(M3 × 12 mm)

Remote controller holder installation

321

Screws

Insert

Slide up

WARNING

Take care to prevent infants and young children from acciden-

tally swallowing the batteries.

CAUTION

• Do not attempt to recharge dry batteries.

• Do not use dry batteries that has been recharged.

Battery (R03/LR03/AAA × 2) loading and remote controller preparation

Press CLOCK ADJUST button to start clock setting.

Set the day of the week by pressing SELECT button (Monday to

Sunday). *By pressing the TEMP. (

∧∨

) buttons, the time indicator

can be changed from a 24-hour to a 12-hour clock.

Press NEXT button to continue.

Set the time by pressing SELECT button.

Pressing





changes the value by the minute.

Pressing down on





changes the value by 10 minutes.

To complete, press the SEND button close to the indoor unit.

Settings may not be properly sent if pressed from a distance.

Notes:

• Use specied type of batteries only.

• Do not mix different types or new and used batteries together.

• Batteries can be used about 1 year in ordinary use.

• If the remote control range noticeably shortens, replace the batter-

ies, and press RESET button as shown in page 5.

OM_01_9387081084-EN.indd 2 4/6/2559 BE 3:51 PM

En-3

AIR CONDITIONER Wall Mounted Type

OPERATING MANUAL

1 Intake grille

Before starting operation, make sure that the intake grille has been

shut completely. Incomplete closing may have an effect on the proper

function or performance of the product.

2 MANUAL AUTO button

Use when the remote controller is lost or there is a malfunction.

Status Action Mode or operation

In operation Press more than 3 seconds. Stop

Stopping Press more than 3 seconds and

less than 10 seconds.

AUTO

Press more than 10 seconds.

(Only for servicing.*)

Forced cooling

After cleaning Press less than 3 seconds. Filter indicator reset

*:To stop forced cooling, press this button or START/STOP button on

the remote controller.

3 Front panel

See page 8

4 Human Sensor

Used for Energy Saving Program. Controls temperature setting by

detecting people in the room.

5 Vertical airow direction louver

Each time you press Vertical SET button on the remote controller, the

angle of the vertical airow direction louver moves as follows:

COOL, DRY or FAN

mode**

FAN mode

1 2

7 865

*: Default setting in each mode.

**: Suggested setting range

• Do not adjust by hand.

• At the beginning of AUTO mode, they may stay on position 1 for a

while for adjustment.

• If the angle is set to position 5-8 for more than 30 minutes in COOL

or DRY mode, the louver will automatically return to position 4.

• Keeping the position 5-8 during COOL or DRY mode may cause

condensation to form, and the drops may damage your property.

6 Power diffuser

In conjunction with movement of the vertical airow direction louver,

the angle of the power diffuser moves as follows:

Vertical airow

direction louver

Power diffuser

1 2

7 865

• In SWING operation, power diffuser does not move.

7 Horizontal airow direction louver

Each time you press the Horizontal SET button on the remote controller,

the airow direction range of the horizontal airow direction louver will

change as follows:

Horizontal airow direction louver

5 4

*: Default setting.

8 Drain hose

9 Remote controller signal receiver

CAUTION

For appropriate signal transmission between remote controller and

indoor unit, keep the signal receiver away from the following items

- Direct sunlight or other strong lights

- Flat-panel television screen

In rooms with instantaneous uorescent lights, such as

inverter type ones, the signal may not be transmitted properly.

In such a case, consult the store of purchase.

ECONOMY indicator (green)

Lights in ECONOMY operation.

TIMER indicator (orange)

Lights in TIMER operation, and blinks slowly when the timer setting

error is detected.

For details, refer to “Auto-restart function” on page 9.

12 OPERATION indicator (green)

Lights in normal operation.

See page 9

Air lter

See page 10

Air cleaning lters

Purify or deodorize the air, and provide fresh airow.

Indoor Unit Overview and Operations

OM_01_9387081084-EN.indd 3 4/6/2559 BE 3:51 PM

En-4

OPERATING MANUAL

CAUTION

• To prevent malfunction or damage of the remote controller:

- Place remote controller at where will not be exposed to

direct sunlight or excessive heat.

- Remove batteries if the product is not going to be used for

an extended period.

- Exhausted batteries must be removed immediately, and

be disposed according to the local laws and regulations of

your region.

• If leaking battery uid comes in contact with your skin, eyes,

or mouth, immediately rinse with plenty of clean water, and

consult your physician.

• Obstacles such as a curtain or wall between the remote

controller and the indoor unit may affect the appropriate

signal transmission.

• Do not apply strong shocks to the remote controller.

• Do not pour water on the remote controller.

Remote Controller Overview and Operations

You can quickly start operation with the following 3 steps:

1 START/STOP button

2 MODE button

Switches operation mode in following order.

AUTO COOL DRY FAN

3 TEMP. (temperature) buttons

Sets the desired temperature.

In COOL or DRY mode, the temperature needs to be set lower than

the current room temperature.

Otherwise, corresponding operation mode may not start.

Temperature setting range

AUTO/COOL/DRY 18–30 °C

Notes:

Temperature control is not available in FAN mode.

4 Remote controller display

In this section, all the possible indicators are displayed for description.

In actual operation, the display is linked with the button operation, and

only shows the necessary indicators for each setting.

5 POWERFUL button

Activates the POWERFUL operation.

The unit will operate at maximum power and strong airow to quickly

cool down the room.

When activated, the indoor unit will emit 3 short beeps.

To turn off, press the POWERFUL button again. The indoor unit will

then emit 2 short beeps.

POWERFUL operation is automatically turned off in the following

situations:

• Adjusted room temperature reaches the set temperature in COOL,

DRY mode.

• 20 minutes have passed after the POWERFUL operation mode has

been set.

Even in situations above, the POWERFUL operation will not

automatically turn off unless it has run for a certain amount of time.

Notes:

• The airow direction and the fan speed are controlled automatically.

• This operation cannot be performed simultaneously with ECONOMY

operation.

• POWERFUL operation will override the OUTDOOR UNIT LOW

NOISE, ENERGY SAVING functions. Both functions, if set, will start

after the POWERFUL operation is turned off.

6 ECONOMY

• Starts or stops ECONOMY operation that saves more electricity

than other operation modes by changing the set temperature to a

moderate setting.

• By pressing the ECONOMY button, the ECONOMY indicator on the

indoor unit turns on.

• In COOL or DRY mode, the room temperature will be adjusted a few

degrees higher than the set temperature.

Notes:

• In COOL or DRY mode, the maximum output of this operation is

approximately 70 % of usual air conditioning operation.

• This operation cannot be performed during temperature monitoring

by AUTO mode.

(continued)

OM_01_9387081084-EN.indd 4 4/6/2559 BE 3:51 PM

En-5

AIR CONDITIONER Wall Mounted Type

OPERATING MANUAL

Remote Controller Overview and Operations (continued)

7 Signal transmitter

Aim at the signal receiver of the indoor unit properly.

• Signal transmit indicator on the remote controller display shows

that the signal from the remote controller is being transmitted.

• Operating range is approximately 7 m.

• You will hear a beep if the transmitted signal has been sent properly.

If there is no beep, press the button on the remote controller again.

8 FAN button

Controls the fan speed.

(AUTO) (HIGH) (MED) (LOW) (QUIET)

• When AUTO is selected, the fan speed is automatically adjusted

according to the operation mode.

9 SWING button

Sets the automatic swing operation. Each time the SWING button is

pressed, the operation will change.

Up/down Left/right Up/down/left/right Stop swing

• The Left/right swing operation will follow the direction as shown on

page 3 "Horizontal airow direction louver"

• The Up/down Swing operation range will differ by mode as follows:

COOL, DRY, or FAN

mode

FAN mode

1 2

Notes:

• SWING operation may stop temporarily when the indoor unit fan is

rotating at very low speed or is stopped.

• In FAN mode, the Up/down swing operation range of 1

↔

5 or 6

↔

8 is decided according to the airow direction previously set before

starting the swing operation.

See page 3

10 Vertical SET button

Adjusts the vertical airow direction.

See page 3

11 Horizontal SET button

Adjusts the horizontal airow direction.

See page 6

WEEKLY timer button

Activates the WEEKLY timer for a maximum of 4 on or off programs

per day, each day of the week.

See page 6

SLEEP timer button

Activates the SLEEP timer that helps you to fall asleep comfortably

with gradual temperature control.

See page 6

ON/OFF timer button

Activates the ON/OFF timer.

NEXT button

Used for adjusting the timer setting.

BACK button

Used for adjusting the timer setting.

17 RESET button

When you press the RESET button, press it gently by using the tip of

a ballpoint pen or other small object in correct direction as shown in

this gure.

RESET

See page 2

18 CLOCK ADJUST button

Used for adjusting the clock.

19 SEND button

Used for sending the timer/clock setting.

See page 6

20 TIMER SETTING button

Used to enter the timer setting mode.

21 SELECT button

Used for adjusting the clock or timer.

OUTDOOR UNIT LOW NOISE button

Starts or stops OUTDOOR UNIT LOW NOISE operation that lowers

noise generated from the outdoor unit by cutting down the rotation

number of the compressor, and suppressing the fan speed.

Once the operation is set, the setting is preserved until you press this

button again to stop the operation, even if the indoor unit operation is

stopped.

on the remote controller display shows that the unit is in

OUTDOOR UNIT LOW NOISE mode.

Notes:

• This operation cannot be performed simultaneously with FAN, DRY

and POWERFUL operation modes.

See page 8

SENSOR button (ENERGY SAVING PROGRAM)

Activates or deactivates the energy saving program.

* The Energy Saving program is ON at the time of purchase.

: The setting must be done while the setting screen is displayed for

each function.

: The button is controllable only when the air conditioner is on.

OM_01_9387081084-EN.indd 5 4/6/2559 BE 3:52 PM

En-6

OPERATING MANUAL

Note for timer settings:

Any interruption of the power supply, such as a blackout or cutting off of a circuit breaker, makes the set internal clock go wrong.

In such a case, the TIMER indicator on the indoor unit blinks, and you need to readjust the setting.

Timer Operation

ON timer or OFF timer

You can set the ON timer or OFF timer with the following steps.

Press the TIMER SETTING button to start the setting.

The WEEKLY indicator will be ashing on the remote controller.

Press the SELECT button to choose the desired mode. The mode

will change as follows:

WEEKLY

ON/OFF

(ON)

ON/OFF

(OFF)

ON/OFF

(ON

⇔

OFF)

SLEEP

(OFF)

Press the NEXT button. Continue to setting for each mode.

* To cancel timer setting during the setting process, press the

TIMER SETTING button again.

Adjust the time by pressing the SELECT button while the clock

indicator is blinking. Each time you press the button, the time will

change by +5/-5 minutes. Pressing down will change the time by

+10/-10 minutes.

Press the SEND button.

To redo the timer setting, perform step 1 to 5 again.

To cancel the ON/OFF timer, press the ON/OFF button while the ON/

OFF indicator is on. (Erases the indicator)

Program timer (combined use of the ON timer and the OFF timer)

You can set an integrated ON–OFF or OFF–ON timer.

Either of the timer whose congured starting time is closer to the

current time works rst, and the order of timer operation is displayed

as follows:

Timer Indicator on remote controller display

ON–OFF timer

OFF–ON timer

To set the program timer, conduct the same steps

①

⑤

for the ON/

OFF timer. (Select ON

⇔

OFF in Step 2)

Notes:

• If you change the setting value for the timer after the program timer

is set, the counting down of the timer will be reset at that moment.

• Time setting for each combination should be within a span of 24 hours

SLEEP timer

To set the SLEEP timer, rst follow steps

①

③

for the ON/OFF timer.

Adjust the time by pressing the SELECT button while the clock

indicator is blinking.

Each time you press the button, the time changes as follows:

00M

30M

hours

(30 min.)

Press the SEND button.

To cancel the SLEEP timer, press the SLEEP button while the SLEEP

indicator is on. (Erases the indicator)

To help you to fall asleep comfortably and prevent excessive cooling in

sleep, the SLEEP timer controls the temperature setting automatically

in accordance with the set time shown as follows. The air conditioner

completely turns off after the set time has elapsed.

Set

temperature

Set time

1 hour

2 °C1 °C

In COOL or DRY mode

WEEKLY timer

ON and OFF timer can be combined, and up to 4 reservations (program

) per day and 28 reservations per week.

Before setting the program, please set the week and time of the air

conditioner rst.

If the week and time are not set, the weekly timer will not operate

correctly at the set time.

Please refer to "remote controller preparation" (page 2).

Example of WEEKLY timer 1

No timer settings

Program

9:00 OFF

Program

11:00 OFF

Program

17:00 OFF

Program

23:00 OFF

Monday to

Friday

Saturday

Sunday

Program

7:00 ON 26°C

Program

9:00 OFF

Wake up

Leave for work

Program

17:00 ON 28°C

Program

23:00 OFF

Come back home

Go to sleep

ON ON ON ON

Example of WEEKLY timer 2

You can specify a given temperature in the ON setting in WEEKLY

timer.

Program

7:00 ON 28°C

Program

9:00 ON 26°C

Program

17:00 ON 27°C

Program

23:00 ON 28°C

* You can set the temperature for AUTO, COOL, and DRY modes within

the range of 18-30°C.

Notes:

●

Operations modes other than the temperature setting will be the

same at the last time operation was stopped, so Cooling → Dry →

Cooling → Dry type of operations cannot be automatically set.

●

If you set the ON timer and OFF timer on the same time, the air

conditioner will run the ON timer. If two ON timer are set at the

same time, the air conditioner will run in the order of the program

number.

●

If there is a power interruption, such as due to a power outage

during the WEEKLY timer setting or a circuit breaker cutting out,

the internal timer of the air-conditioning will be incorrect. (See page

9 "Auto-restart".) In such a case, the main timer lamp will notify you

of this by ashing, so carry out matching of the time and date. (See

page 3 "remote controller preparation".)

●

You cannot use the WEEKLY timer together with the other timers.

If you want to run the product on WEEKLY timer after using the ON/

OFF Timer, Program Timer, or SLEEP Timer while the WEEKLY

timer is running, you need to activate the WEEKLY timer again.

(continued)

OM_01_9387081084-EN.indd 6 4/6/2559 BE 3:52 PM

En-7

AIR CONDITIONER Wall Mounted Type

OPERATING MANUAL

Timer Operation (continued)

To set the WEEKLY timer, rst follow steps

①

③

on page 6 for

the ON/OFF timer.

Select the program number and the day using the SELECT

button.

Program 1Week

Program

Monday

Program

Tuesday Program Sunday

Program

1Week

Program

Monday

Program

Saturday Program Sunday

Press the NEXT button, when the program number and day you

want to set are ashing.

Using the SELECT button select the operation mode (ON timer,

OFF timer, or without a timer).

To operate without a timer

1. Press the NEXT button to go back to step 4 and congure the

next setting.

2. Press the SEND button to nish

Press the NEXT button.

Press the SELECT button to set the desired ON time or OFF

time.

If you selected OFF in step 5

1. Press the NEXT button to go back to step 4 and congure the

next setting.

2. Press the SEND button.

Press the NEXT button.

Press the SELECT button to set the temperature.

If you want to move on to the next setting, press the NEXT button,

return to step 4 and congure the next setting.

To complete the setting, press the SEND button.

If you want to cancel the setting midway, please press the

TIMER SETTING button instead of pressing the SEND button.

Notes:

● When canceling the WEEKLY timer, select No Timer Operation in

Step 5 in the WEEKLY timer setting.

● If you want to go back to the previous step when conguring

settings, press the BACK button to return to the previous step.

● Press the SEND button, when you are close to the main unit. If you

do so when far from the main unit, the signal may not get properly

sent, and the settings may not get properly congured.

● To check the schedule, repeat steps 1 to 3 to enter the WEEKLY

timer mode, then use the SELECT button to browse through the

WEEKLY timer settings in the order shown in step 4.

● To cancel the WEEKLY timer, press the WEEKLY button while the

WEEKLY indicator is on. (Erases the indicator)

OM_01_9387081084-EN.indd 7 4/6/2559 BE 3:52 PM

En-8

OPERATING MANUAL

Human Sensor (Energy Saving)

To prevent waste of electricity, this function controls the temperature

setting when no one is occupying the room. Energy Saving program is

on at the time of purchase.

To activate the Energy Saving program, press the SENSOR

button.

indicator will be ashing on the remote controller

display.

To deactivate the Energy Saving program, press the SENSOR

button again.

will no longer be shown on the remote controller

display.

About the ENERGY SAVING Operation

If no one enters the room for approximately 20 minutes, the set

temperature will be automatically controlled.

(When someone comes back into the room, the human sensor will

detect this, and automatically revert to the original settings.)

Operation

mode

Operating details

(if there is no one in the room for a while)

COOL/DRY

The set temperature will be increased by a maximum of

approximately 2˚C.

AUTO

This runs the ENERGY SAVING function automatically

for the selected mode (Cooling/ Drying).

● When using together with the SLEEP timer (page 6), the SLEEP

timer will be prioritized.

90°

7 m

50° 50°

● Application range is follows.

Vertical angle 90° (Side view) Horizontal angle 100° (Top view)

ENERGY SAVING function may not work when the room temperature is

very different from the temperature dened in temperature setting, such

as when immediately after starting the operation.

About the HUMAN SENSOR

Details about detection with the human sensor

The human sensor detects whether there are people in the room

by looking for movement by people in the room.

Since the human sensor detects infrared light given out by

people, there may be cases where this detection is incorrect.

Situations in which the sensor will detect no people in the

room, even when there is someone there

When the temperature is high and the difference with be-

tween people’s body temperature is small.

(Such as during the summer when the temperature is 30˚C

or higher)

When there is someone in the room, but they do not move

for a long period of time.

When someone is hidden behind a sofa, other furniture,

glass, or in similar situations.

When someone is wearing extremely thick clothing and has

their back facing the sensor.

Situations in which the sensor will incorrectly detect people

in the room, even when there is no one there

When there is a dog or a cat moving around in the room.

When the wind is making curtains or plants move.

When there are heating units, humidiers, or electric appli-

ances such as oscillating electric fans operating.

Notice

General Informations on Operation

Auto-restart function

In event of power interruption such as a blackout, the air

conditioner stops once. But it restarts automatically and

performs previous operation when the power supply is resumed.

If any power interruption occurs after the timer is set, counting

down of the timer will be reset.

After the power supply is resumed, the TIMER indicator on the

indoor unit blinks to notify you that there has been a timer fault.

In such a case, reset the timer for your opportune time.

Malfunctions caused by other electrical devices:

Use of other electrical appliances such as an electric shaver or

nearby use of a wireless radio transmitter may cause the malfunction

of the air conditioner.

If you encounter such a malfunction, turn off the circuit breaker once.

Then turn it on again, and resume operation by using the remote

controller.

Temperature and Humidity Range

Permissible ranges of temperature and humidity are as follows:

COOL/DRY Indoor temperature About 18 °C to 32 °C

Indoor humidity Below approximately 80%.

If the air conditioner is used continuously for many

hours, water may condense on the surface and drip.

If the unit is used under higher temperature conditions than those noted here, the automatic protection circuit may operate, interrupting the operation.

If the unit is used under lower temperature conditions than those noted here, the heat exchanger may freeze, causing water leakage or other mal-

function.

●

Do not use the air conditioner for any purpose other than room cooling/dry or fan.

OM_01_9387081084-EN.indd 8 4/6/2559 BE 3:52 PM

En-9

AIR CONDITIONER Wall Mounted Type

OPERATING MANUAL

Care and Cleaning

CAUTION

• Before cleaning the indoor unit, be sure to turn it off and all the power supply has been disconnected.

• Before starting operation, make sure that the intake grille has been shut completely. Incomplete closing of the intake grille might have an

effect on the proper working or performance of the air conditioner.

• Do not touch the aluminum ns of heat exchanger built-in the indoor unit to avoid personal injury when you maintain the unit.

• Do not expose the indoor unit to liquid insecticides or hair sprays.

• Do not stand on slippery, uneven or unstable surfaces when you maintain the unit.

Daily care

When cleaning the indoor unit body, mind the following:

• Do not use water hotter than 40 °C.

• Do not use scouring cleanser, volatile solvents such as benzene or

thinner.

• Wipe the unit gently by using soft cloth.

Cleaning the intake grille

Open the intake grille in direction of the arrow

. While gently

pressing the left and right mounting shafts of the intake grille

outward

, remove the intake grille in direction of the arrow

Wash the intake grille gently with water or wipe it gently with a

soft cloth moisten with warm water.

Then wipe it with a dry and soft cloth.

While holding the grille horizontal, set the left and right mounting

shafts into the pillow blocks at the top of the panel

. To latch

each shaft properly, insert the shaft until it snaps.

Then close the intake grille

Press 4 places on the intake grille to close it completely.

Cleaning the air lters

Mind that you have a periodical cleaning of the air lters to prevent

reducing the operation efciency of the product.

Using of clogged air lter with dust will lower the product performance,

and may cause airow reduction or increase of operating noise.

Clean the air lters once every 2 weeks under normal use.

Open the intake grille.

(Refer to

of step 1 in “Cleaning the intake grille”.)

While holding the intake grille with your hand, pull up the handle

of the lter in direction of the arrow and release the 2 claws

Then pull the lter out with gently sliding it downward

Filter holder and air cleaning lter are attached on the rear side

of the air lter. Remove them from the air lter by unlatching each

corner of the lter holder

Remove dust by using a vacuum cleaner or by washing the lter.

When you wash the lter, use neutral household detergent and

warm water.

After rinse the lter well, dry it throughly in a shaded place before

you reinstall it.

Attach the air cleaning lter and the lter holder to each air lter.

Attach the air lter with aligning both side of the lter with the front

panel, and push in the lter fully.

Note:

Make sure that 2 claws are rmly snapped to the guide holes on

the panel.

Close the intake grille rmly.

(Refer to step 4 in “Cleaning the intake grille”.)

OM_01_9387081084-EN.indd 9 4/6/2559 BE 3:52 PM

En-10

OPERATING MANUAL

Care and Cleaning

Replacing the air cleaning lter

Remove the air lter. (Refer to step 1 in “Replacing the air lter”.)

Release 2 latches

of the lter holder, and turn over the holder

in direction of arrow

Remove the soiled air cleaning lter

Note:

Air cleaning lter is attached on each air lter.

Attach new or maintained air cleaning lter

to the lter holder.

New air cleaning lter can be attached to either of the right holder

or the left holder.

Latch 2 corners of the lter holder

to the air lter rmly.

Reinstall the air lter. (Refer to step 6 in “Cleaning the air lter”.)

Close the intake grille rmly.

(Refer to step 4 in “Cleaning the intake grille” on page 9.)

Following 2 types of air cleaning lters are used in this product.

When you replace them, purchase dedicated air cleaning lters for this

product.

Apple-catechin lter: UTR-FA16

(1 sheet)

The Apple-catechin lter uses static electricity to clean ne particles

and dust in the air such as tobacco smoke and plant pollen that are

too small to see.

• This lter is disposable. Do not wash or reuse it.

• Once you open the package, use it as soon as possible. The

cleaning effect is reduced if the lter is left with the package opened.

• Replace the lter once every 3 months under normal use.

• By setting the fan speed high, the air cleaning effect increases.

Ion deodorization lter: UTR-FA16-2

(Light blue, 1 sheet)

The lter deodorizes by powerfully decomposing absorbed odors

using the oxidizing and reducing effects of ions generated by the

ultra-ne-particle ceramic.

• To maintain the deodorizing effect, clean the lter once every 3

months as follows:

Remove the lter.

Flush the lter with high-pressure hot water until the surface of

the lter is covered with water.

Wash the lter gently with diluent nuetral detergent. Do not wash

it by wringing or rubbing to prevent reducing the deodorizing

effect by damage.

Rinse the lter well with water ow.

Dry the lter throughly in a shaded place.

Reinstall the lter to the indoor unit.

• Replace the lter once every 3 years under normal use.

After extended non-use of the unit

If you have shut down the indoor unit for 1 month or more, perform the

FAN operation for half a day to dry the internal parts throughly before

you perform normal operation.

Additional inspection

After long period of use, accumulated dust inside the indoor unit may

reduce the product performance even if you have maintained the unit

with instructed daily care or cleaning procedures written in this manual.

In such a case, a product inspection is recommended.

For more information, consult authorized service personnel.

OM_01_9387081084-EN.indd 10 4/6/2559 BE 3:52 PM

En-11

AIR CONDITIONER Wall Mounted Type

OPERATING MANUAL

WARNING

In following events, immediately stop operation of the air conditioner, and disconnect all the power supply by turning off the electrical

breaker or disconnecting the power plug. Then consult your dealer or authorized service personnel.

As long as the unit is connected to the power supply, it is not insulated from the power supply even if the unit is turned off.

• Unit smells of something burning or emits smoke

• Water leaks from the unit

Following symptoms do not indicate product malfunction, but they are normal functions or characteristics of this product.

Symptom Cause See page

Operation is delayed after

restart.

To prevent blowout of the fuse, the compressor will not operate while the protection circuit is working

for about 3 minutes after sudden OFF→ON operation of the power supply.

–

Noise is heard. During operation or immediately after stopping the air conditioner, refrigerant owing sound may be

heard. Also it may be particularly noticeable for 2–3 minutes after starting operation.

–

During the operation, a slight squeaking sound produced by the minute expansion and contraction of

the front panel caused by temperature change may be heard.

Smell coming from the unit. Various smells generated from interior textile, furniture, or cigarette smoke absorbed into the air

conditioner may be emitted.

–

Mist or steam is emitted from

the unit.

In COOL or DRY mode, a thin mist generated by condensation formed with sudden cooling process

may be emitted.

–

Airow is weak or stops. In DRY mode, the indoor unit operates at low fan speed to adjust the room humidity, and may stop

from time to time.

–

When the fan speed is set to “QUIET”, the fan rotates at very low speed and the airow is reduced. –

In COOL mode, the indoor unit fan may stop from time to time when the outdoor unit is stopped. 4

When monitoring operation is performed in AUTO mode, the fan rotates at very low speed. –

Before you call for or request servicing, troubleshoot a problem by performing following checks:

Symptom Diagnostic See page

Does not operate at all.

 Has the circuit breaker been turned off?

 Has there been a power outage?

 Has a fuse blown out or the circuit breaker been tripped?

–

 Is the timer operating?

Poor cooling performance.

 Is the air lter dirty?

 Is the intake grill or outlet port of indoor unit blocked?

–

 Is the room temperature adjusted appropriately?

 Is a window or door left opened?

 Is direct or strong sunlight shinning into the room in cooling operation?

 Are there other heating apparatus or computers operating, or too many people in the room in cool-

ing operation?

–

 Is the fan speed set to “QUIET”?

When the fan speed setting is set to “QUIET”, noise reduction is prioritized and the air-conditioning

performance may become lower. If the volume of provided airow is not agreeable to your prefer-

ence, set the fan speed to “LOW” or higher fan speed.

 Has the OUTDOOR UNIT LOW NOISE mode been set?

The unit operates differently

from the remote controller

setting.

 Are the batteries used in the remote controller exhausted?

 Are the batteries used in the remote controller loaded properly?

Immediately stop operation and turn off the electrical breaker in following cases. Then consult authorized service personnel.

• The problem persists even if you perform these checks or diagnostics.

• The OPERATION indicator and TIMER indicator blink while the ECONOMY indicator is blinking fast.

Troubleshooting

OM_01_9387081084-EN.indd 11 4/6/2559 BE 3:52 PM

OM_01_9387081084-EN.indd 12 4/6/2559 BE 3:52 PM

Fujitsu ASMG24CMCA Operating instructions

Brand: Fujitsu

Model: ASMG24CMCA

Type: Operating instructions

This manual is also suitable for

ASMG18CMCA

Download PDF

report

Fujitsu ASMG24CMCA Operating instructions

This manual is also suitable for

Fujitsu ASMG24CMCA Operating instructions

Related papers

Other documents