Kodak 40FHDX900s User manual

User Manual

R9 Series

Introduction 1

Warnings & Safety Precautions 1

Features 2

Safety Information 2

Important Safety Precautions 3

Prepration Stand Installation 4

Functional Overview Fornt & Side Panel 5

Rear Panel 6

Connections 7

Remote Control 8

Basic Operation 11

Menu Operation 12

Media Play 19

PC Setting 20

Instructions for Platform Operation 21

Specification 24

Troubleshooting 25

CONTENTS

INTRODUCTION

Thank you for choosing our product. To be able to make use of all application options, we

recommend that you should read this operation manual carefully and preserve it for quick

access, if required.

Do not touch any parts in the set and do not make changes to any settings not described

in this operating manual.

The LED Screen is a high-tech product which consists of more than 9,00,000 control

elements. Any Non-active red, blue or green spots / lines that might appear on the screen

occasionally, have no efect on the performance of the screen or television and may

disappear over a short period of time.

WARNINGS AND SAFETY PRECAUTIONS

Warning:

– To prevent damage to the TV which may result in a ﬁre or electrical shock hazard, do not

expose the TV set to rain or excessive moisture.

– Do not rub or strike the Active matrix LED with any thing hard as this may scratch, mark or

damage the active matrix LED permanently.

– For safety, do not place vessels or any container which contain ﬂuid including water, on or

near the TV.

– Do not insert any objects in the ventilation slots.

Service:

– Do not remove the back cover of the set as this can expose you to very high voltage and

other hazards. If the set does not operate properly, unplug it and call Thomson LED

TV customer care.

Antenna:

– Connect the antenna cable to the socket marked ANT IN on the back cover. For best

reception an outdoor antenna should be used.

Location:

– Position the set so that no bright light or sunlight falls directly on the screen. Reﬂections on

the screen may aﬀects the picture quality & viewing of television.

– Soft and indirect lighting is recommended for comfortable viewing.

– Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or

heat.

– Adequate ventilation is essential to prevent set failure.Ensure that the set is placed in a

position to allow a free ﬂow of air. Do not cover ventilation opening on the back cover. Do

not place the set in an enclosure or very close to walls.

– Avoid excessively warm locations to prevent possible damages to the set.

– Place the television on a solid and ﬂat surface, if not wall mounted.

1

FEATURES

SAFETY INFORMATION

2

HD/FHD Resolution–

Extra Slim Design–

200,000:1 Dynamic Contrast Ratio–

HDMI Connectivity–

Full Multimedia Interface–

Seven Picture Modes–

Five Sound Modes–

o o

178 x178 Viewing Angle–

PC Connectivity–

Dynamic Noise Reduction–

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

High voltages are used in the operation of

this product. To reduce the risk of electric

shock, do not remove cover of the cabinet,

refer for servicing to qualified service personal.

If the LED TV requries any changes or coarse adjustment, electric shocks

are imminent. Do not attempt to open contact customer support for needed

overhual.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating & maintenance (servicing) instruction in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol within an

equilateral triangle is intended to alert the user to the

presence of uninsulated dangerous voltage within the

products enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

Warning

IMPORTANT SAFETY PRECAUTIONS

3

1 Read & keep this instruction manual.

2 Read all warnings.

3 Clean only with dry cloth.

4 Do not block any ventilation openings. Install in accordance with the manufacturer’s

instrutions.

5 Do not install near any heat source such as radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce heat.

6 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong.

7 The wide blade or third prong are provided for your safety. If the provided plug does not

fit into your outlet, protect the power cord from being walked on or pinched particularly

at plugs, socket outlets and the point where they exit from the apparatus.

8 Only use attachments / accessories specified by the manufacturer.

9 Use only with the bracket or table stand specified by the manufacturer or sold with the

apparatus.

10 Unplug this apparatus during lightning storms or when unused for long period of time.

11 To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

12 The apparatus should be disconnected from the mains by placing the power / standby

switch in the standby position and unplugging the power cord of the apparatus from the AC

main outlet.

13 The socket outlet should be installed near the equipment & should be easily accessible.

14 This product should never be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacture’s instructions have been adhered

to.

15 The apparatus should not be exposed to dripping or splashing & objects filled with liquid,

such as vases, should be placed on the apparatus.

16 Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted

candles).

17 Wall or ceiling mounting - The appliance should be mounted to a wall or ceiling only as

recommended by the manufacturer.

Servicing should be carried out by qualified service personnel only. To reduce the risk of

electric shock do not perform any servicing other than that contained in the operating

instructions.

PREPARATION

4

Stand Installation

The TV base will be separated with the TV unit. You should install the base before

you use the TV unit.

- Place the TV with its front side facing down on a cushioned flat surface.

- Place the base on the hinge of TV unit, with the base direction shown under

the base. (See the picture)

- Tighten the supplied screws to fix the TV stand securely in place.

(Screws - Provided with TV unit)

WARNING

- The TV stand may not be securely fixed in place after repeated tightening

and loosening of screws.

- During assembling and disassembling the TV stand, please use your hand

to support it. Failing to do so may cause the TV stand to fall and result in

personal injury / damage to the product.

- After installing the TV stand, please ensure that the screws are tightened

firmly. Failure to do so may cause the TV set to tip over or damage it.

(Screw fixes here)

FUNCTIONAL OVERVIEW

5

Front & Side Panel

1 Power Light

On Standby Mode, the light

turns red.

2 Infrared Remote Sensor

Receives the signals from the

remote control.

3 Power

Press to turn TV on or turn to

standby mode.

4 Menu

Press to display the setup menu on

the TV screen.

5 CH-, CH+

Press to select desired channels. or

press to select or adjust a menu item.

6 Vol-, Vol+

Press to adjust Volume level or press

to select & adjust a menu item.

7 Input

Press to select source of viewing & adjust

video input modes TV, AV, HDMI, USB,

YPBPR

FUNCTIONAL OVERVIEW (AS PER MODEL)

6

Rear Panel

VIDEO

AV1 IN

L - AUDIO - R

Y / VIDEO

Pb Pr

AV2 IN

*EARPHONE

HDMI x 3

USB3

RJ 45 HDMI 1 HDMI 2 VGA

PC

AUDIO

TV USB 1

USB 2

COAX

L-AUDIO-R

IN

- LAN (Local Area Network)

For Internet connection

- USB

Insert USB

- HDMI input Terminal

Connect to equipment with HDMI output

- VGA(PC IN) Input Terminal

Connect to PC.

- PC / HDMI Analog Audio Input Terminal

Connect to equipment using HDMI-DVI

connection or PC with audio output.

- AV 1 & AV 2 In / YPBPR

Connect the video output jack of DVD or VCR & equipment using with the set-top box

- Antenna Input Terminal

Connect to equipment with antenna output or

wall antenna socket.

*This image is for reference only to explain uses of various connections. Actual product specifications may differ from the above.

NOTE :- Earphone (optional) connect the earphone lead with extra speaker satellite units

CONNECTIONS

7

You can connect VCR, DVD player, set-top box, computer, game console or other

equipment to the TV. To view external source images, press to select the input

source.

Source

Connecting an AV Equipment with HDMI Connector

Connecting an AV Equipment with Composite Connector

Connecting an AV Equipment with VGA Connector

- If the external equipment has DVI output, you can connect it to the HDMI terminal using a HDMI-DVI cable.

In case of using the HDMI-DVI cable, connect analog audio signal to RGB/HDMI analog audio input terminal.

- Please refer to the user manual of the external equipment for more information on connection to the TV.

- Please disconnect all power supplies to the equipment & TV before connection.

- Compatibility of the TV set & external equipment is dependent on hardware compatibility of both.

REMOTE CONTROL

8

Installing the remote control batteries

- Open the battery cover.

- Insert batteries (2x AAA size batteries)

Place batteries with their terminals observing

the (+) & (-) indications.

- Replace the cover & press down until the lock

snaps closed. If the remote control is not used

for an extended period of time, remove the

batteries from the remote control as damage

may result due to electrolyte leakage from the

batteries.

- The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

- Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

- Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries

according to the instructions.

- Do not dispose of batteries in a fire, danger of explosion

- Batteries not covered under warranty.

Note:

POWER

FREEZE

S.MODE

P.MODE

FAV

FAV -/Setting

FAV +/Capture

Turns TV into STANDBY ON/OFF.

Select to freeze the scene still on the screen.

Recalls / changes presetted sound settings.

Recalls / changes presetted picture settings.

Press to add or remove your favorite channels under TV menu.

Press to switch your favorite channels under TV menu. / Press to open set-up.

Press to switch your favorite channels under TV menu.

- Navigates vertically Up/Down through the Menu/Sub Menus.

- To enter character/numbers in program name parameter.

- To navigate channel Up/Down through valid channels.

- Navigates horizontally Right/Left through the Menu/Sub menus.

- To enter in Menu/Sub menus & to adjust Vol +/-.

- To navigate the letter in program name parameter.

- To select the time.

- To select Source by Up/Down arrow key.

- Increase / Decrease the value of selected items & set the

parameter On/Off.

- To enter in sub menu.

- Enter to edit program name parameter.

P

OK

EXIT

Press to exit the OSD menu

FUNCTIONS

REMOTE CONTROL

9

MENU

INPUT

VOL +/-

PA+/-

ECO

MUTE

- / -- / CH. LIST

Q.VIEW

Sleep/

Delete

Sub Title/

Copy

Aspect

GOTO

/

ROOT

/

Speaker

Media

To select menu OSD window and return to upper menu.

Input source selection.

Select to increase or decrease volume.

Select to increase or decrease volume for power audio.

This key provides the different power saving modes. The current mode is

displayed with ecovision symbol on the screen. In audio only mode display is off

& only audio is on. Press any key to exit audio only mode. Note: VOL+/-, PA+/- &

Mute can fuction even as panel is off. Note: Audio only mode is not available in

models 32” and above.

Turns sound OFF or ON

Figures 0-9 are used to directly input channel number.

- Press this key to enter the program number for different digit eg. -/--/---

- Press for the list of program.

Press this key to toggle between the current & the previous program you were watching.

- Press this key to save channels when manual tuning or to delete channel when editing

TVprogram in program edit function.

- To set sleep timer except when in program Edit Menu or USB mode

- To delete item selected in USB mode.

- Press this key to display sub title list.

- Press this key to rename channels in program edit function.

- Press this key to switch On/Off internal speaker used in TV set.

- Press this key to swap channel in program edit function.

- Press this key to open media center.

- Press this key to switch aspect ratio.

- Press this key to skip channel in program edit function.

- Press this key to STOP in USB mode

- Press this key to PLAY/PAUSE in USB mode

- Press this key to FAST REVERSE in USB MODE

- Press this key to FAST FORWARD in USB MODE

- Press this Go to key to select play time position

When playing the Photo or Video or Mp3 or Text, if you select ROOT key it will stop

playing & return to the current list in USB mode.

Press to open home page.

- Press this key to play the previous track.

- Press this key to play the next track.

REMOTE CONTROL

10

Power On/Off

Turning on the TV

- Plug the TV’s power cord into a wall outlet (after this step, the main unit will turn on

and enter stanby mode automatically).

- Press the (Power) button on the TV, or press the (Power) button on the remote

control. The TV will turn on.

Placing In Standby Mode

Your TV can be placed in Standby mode in order to reduce the power consumption.

The standby mode can be usefull when you wish to interrupt viewing temporarily

(during a meal, for example).

- Press the Power Button.

- To switch back on, simply press power button.

Remark: Do not leave your TV in standby mode for long periods of time. (When you

are away on holiday, for example). It is the best to unplug the set from the mains and

aerial.

Changing Programmes

Using the programme selection buttons on the remote control to change

programmes

To select a programme, press the corresponding programme selection button

remote control. For example, to select programme 8, press the “8” programme

selection button on the remote control.

Using the P+/- buttons to sequentially change programmes

Press P+/- buttons on the remote control or on the TV to sequentially seletct

the TV programmes available in you area.

Using the button to return to sequentially change programmes

To return to the previous viewed programme, press the button on the remote

control.

BASIC OPERATION

11

Power On/Off

To turn on the TV

- Connect the power play into the wall outlet.

The power indicator lights in red, indicating

that the TV is in Standby Mode.

-Press

The Power indicator lights turns off & the

TV turns on.

To turn off the TV

-Press

The power indicator lights in red & the

TV turns off to standby mode.

- It takes approximately 10 sec. for the

picture to appear after the TV is turned on.

- The TV will switch to standby mode auto-

matically if there is no signal input for 10

minutes.

- If the TV will not be used for a long periods

of time, unplug the TV from the wall outlet.

Channel Selection

To select channel

Press P+/- or Program Select buttons to select

the channel number directly.

Input Source Selection

To select input “SOURCE”.

- Press to select the desired input source,

then press “enter” to enter. The selected

input source image displays.

Volume Adjustment

To change the volume

- Press V+ to increase the sound volume.

- Press V- to decrease the sound volume.

To Mute the sound

- Press to temporarily turn off the sound.

- Press or V+ to restore the sound to

previous level.

- You can decrease the sound volume by pressing

V- while the sound is muted.

On-Screen Displays (OSD) Selection

& Adjustment

- Press “MENU” to display the main menu.

- Press to select a menu. The selected

menu page displays.

- Press to set your selection.

- Press to choose an item on the menu

page & press to set your selection.

- Press to adjust an item value or choose

options.

- Press “MENU” to return to the menu, press

”MENU” again to exit.

The OSD menu screen will be closed auto-

matically when no operation has been made

for the set OSD menu display time.

INPUT Source : TV, AV-1, AV-2 , HDMI - 1,

HDMI – 2 , HDMI – 3 , USB-1 , USB-2 ,

y.pb,Pr , VGA

CHANNEL :

Auto Tunning : You can tuto tune all RF channels in ATV input source only.

ATV Manual Tunning : Channel

: Color System

: Sound System

: Search

: Frequency

CH1

Auto/PAL/NTSC/SECAM

BG/DK/I/M

< >

62.25 MHz

MENU

Program Edit

:

1 S-00 ATV

Delete Edit Move Skip

O

G

Y B

Picture

: Standard / Soft / User / Vivid/Natural/Sports/Lightness

ATV Manual Tunning Contrast

Brightness

Hue

Sharpness

Saturation

ECO

back Light

Color Temperature

Aspect Ratio

Image Noise

Reduction

: 0 - 100

: Off/Low/Middle/High

: 0 - 100

: Standard / Warm / Cool

: 16:9

: Off/Weak/Middle/Strong

SOUND :

: 2016 / 7 / 1

: 09:02:40

: Setting off Time Off / On

Date

Current Time

Off Time

Standard / Music / Movie / Sports / User

Bass

Treble

Balance

AVC

Surround

SPDIF Output

: 0 - 100

: Off / On

: PCM/RAQ/OFF

TIME :

: Setting Boot Time OFF/ON

On Time

Hour 9 (0-23)

Minute 05 (0-59)

(Off Time must be more, than 1 minutes after the current time)

Hour

Minute

Source

(Schedule time must behind the current time)

9

43

ATV

: Off / 10 min / 20 min/ 30 min/ 60 min / 90 mibn /

120 min / 180 min / 240 min.

Sleep Time

: Always / 5 Sec / 10 Sec / 15 Sec / 20 Sec / 30 Sec.

: Off / On

Stand by On : OFF / ON

ARC : OFF / On

Menu Time

Blue Screen

HDMI CEC

SETTING :

: 0 - 100

: >>>>

Menu Opcity

Restore To Default

MENU OPERATION

12

MENU OPERATION

Auto Tuning

ATV Manual Tuning

Program Edit

Channel

Picture

Sound

Time

Setting

Select

Confirm

Exit

13

Channel Setting (Use for TV)

- Press the “MENU” button on the remote

control to enter the OSD menu. Then

press buttons the “CHANNEL”.

- Press buttons to select the desired item,

then press or ENTER to enter.

- Press buttons on the remote control to

adjust desired item.

- Press the “MENU” button on the remote

control to return to upper menu.

At ATV input source, the first page showed is CHANNEL. At non ATV input source, the first page

is PICTURE as default. Currently press ENTER to get in sub menu, submenu highlight fixed on

press button key, the subtopic turns up with full screen.

Note : CHANNEL can be only selected under ATV condition, others can’t be used.

- Auto Scan : Enter Auto, it shows the process of frequency & the number of channels.

Press to select country & Tune Type at first,

press to select start or cancel, then press OK

button to start or exit Auto Scan.

- TV Manual Tuning:

Storage To : Current storage space shows, the following

option are available : 1-200.

System : Default option depends on country selection.

The following option are available : BG, I, DK

Current CH : Current channel shows.

Search : Can be searched at full channel condition.

Frequency : Show the current frequency & follow

search or Fine-Tune to adjust.

NOTE : After tuning by hand, make sure to press red button for storage, otherwise all channels searched

would not be stored after switching condition.

MENU OPERATION

14

- Program edit :

There are 3 items in the Preference page : Skip, Type

Select : Select your channel name by moving the cursor.

Delete : Delete current channel, as follows :

Press UP/DOWN buttons to choose the channel which you want to delete, then

press RED button to delete the current channel.

GREEN Button :

Modify current channel name, only used in ATV mode.

- At normal condition, press GREEN button to enter RENAME mode.

- At RENAME Mode :

MENU : Press to exit RENAME mode, back to normal.

EXIT : Press to exit menu.

UP/DOWN : Press to switch letters, numbers or signs.

LEFT/RIGHT : Press to switch left & right, can select by circle.

GREEN : Press to exit RENAME mode, return normal condition.

Yellow Button :

Channel switching function, ATV available as default.

- At normal condition, enter SWAP mode, & current selected channel is mobile channel X.

- At SWAP mode :

MENU : Press to exit SWAP mode, turn to normal condition.

EXIT : Press to exit menu.

UP/DOWN : Choose switch channels.

YELLOW : If current selected channel is what selected before X, no any other action,

Otherwise, the current channel is channel Y, need to exchange X& Y condition. But the

channel number stays 1,2,3,...... order as before.

BLUE Button :

Choose if skip the channel when CH+/- channel tuning.

At Non Skip channel, press BLUE button, & Skip the current channel

At skip channel, press blue button to cancel skip.

MENU OPERATION

15

Picture Setting

You can adjust picture effect here, such as contrast,

brightness & etc.

- Press the “MENU” button on the remote

control to enter the OSD menu.

Then press buttons to select the “PICTURE”.

- Press button to select the desired item to enter.

- Press buttons on the remote control to adjust

desired item.

- Press the “MENU” button on the remote control

to return upper menu.

Picture Mode : Press buttons to select. The following option are available.

“Standard, Mild, User, Dynamic”

Contrast : Adjust image contrast.

Brightness : Adjust image brightness.

Color : Adjust the color saturation.

Sharpness : Adjust the sharpness level of image.

Tint : Determines the tint of the screen (This is only available with NTSC).

Color Temperature : Adjust the color temperature level of image. The following option are

available, “Normal, Warm, User, Cool”.

RED/GREEN/BLUE : Press buttons to adjust numeric size, Press MENU button to turn back

picture main menu.

Aspect Ratio : Press buttons to select, 16:9, Zoom 1, Zoom 2, Panorama, 4:3, Just Scan

Noise Reduction : Press buttons to select Off, Low, Middle, High

Color Temperature

You can select your favorite color temperature.

- Press the “MENU” button on the remote

control to enter the OSD menu. Then press

buttons to select the “PICTURE”

- Press button to select the “Color Temperature”

- Press buttons on the remote control to choose

color temp’s value.

- Press the “MENU” button on the remote

control to return to upper menu.

User : Adjust the color value.

Normal : Keep the original white color

Warm : Adjust the white color to a little bit red.

Cool : Adjust the white color to a little bit blue.

Remark : The changes you made will be stored automatically.

MENU OPERATION

16

PC Setting (Only for PC Mode)

The function only used in PC port to adjust PC position. Enter

the screen page with buttons or ENTER button.

- When input PC source, you can go to PC to set up menu.

- Press the “MENU” button on the remote control to enter

the OSD menu. Then press buttons to select the

“PICTURE SETUP” in main menu.

- You can press ENTER buttons to enter PC setup mode

after selecting PC setting , & the press buttons to

select your desired item press buttons to adjust.

- Press the “MENU” button on the remote control to

return to upper menu.

- In PC function operation will instruct more clear.

Sound Setting

You can customize different sound mode to get best effect.

- Press the “MENU” button on the remote

control to enter the OSD menu. Then press

buttons to select the “SOUND”

- Press button to select the desired item

to enter.

- Press buttons on the remote control to

increase or decrease the value of desired

item.

- Press the “MENU’ button on the remote

control to return to upper menu.

Auto Adjust : Press buttons, TV system adjust by itself, it can adjust, H position, V position, Phase & so

on that can make the image in center & display best.

H. Position : Adjust Horizontal Position of the PC Screen.

V. Position : Adjust the Vertical Position of the PC Screen.

Size : Adjust the size of the PC Screen.

Phase : When necessary, adjust the pixel phase of the picture to avoid picture interference.

Sound Mode : Press buttons to select one of the following options are available “Standard, Music, Movie,

Sports User”.

Treble : Adjust treble effect.

Bass : Adjust bass effect.

Balance : Adjust balance effect.

Auto Volume : (Auto volume control, when you turn on the TV, this feature allows the TV to

automatically adjust the sound output from level to the previous level of

last time when you turned off the TV) : On/Off.

Surround Sound : Select it to enter, then you can select Off or On.

MENU OPERATION

Time

Clock

Off Time

On Time

Sleep Timer

Auto Sleep

09/NOV 04:19

13:57

13:58

Off

On

17

Time Setting

You can set the TV’s time & you should set time if you use the automatic On/Off times.

- Press the “MENU” button on the remote control to enter

the OSD menu.

Then press buttons to select the “TIME”.

- Press button to select the desired item to enter.

- Press buttons on the remote control to adjust desired item.

- Press the “MENU” button on the remote control to upper menu.

Sleep Timer : Press buttons to select your desired item (Off,

240 min., 180 min., 120 min., 90 min., 60 min., 30 min., & 10 min.)

Auto Sleep : Within 10 min. there is no signal, the TV will auto sleep

Clock

- Press the “MENU” button on the remote control to enter

the OSD menu.

Then press buttons to select the “TIME”.

- Press button to select CLOCK, then press ENTER button

to enter.

- Press buttons to select the desired item.

- Press the “MENU” button on the remote control to return upper

menu.

- Press the “MENU” button on the remote control to enter

the OSD menu.

Then press buttons to select the “TIME”.

- Press button to select Off Time, then press ENTER button to

enter.

- Press buttons to select the desired item, then press

buttons on the remote control to set the time.

- Press the “MENU” button on the remote control to return upper

menu.

Off Time

Page is loading ...

Kodak 40FHDX900s User manual

Kodak 40FHDX900s User manual

Related papers

Other documents