JVC GVT0294-006B User manual

INSTRUCTIONS

GVT0294-006B

[UN/J]

UX-J51

MICRO COMPONENT SYSTEM

— Consists of CA-UXJ51 and SP-UXJ51

TM

For customer use:

Enter below the Model No. and Serial No. which

are located either on the rear, bottom or side of

the cabinet. Retain this information for future

reference.

Model No.

Serial No.

UX-J51_EN.indb 1UX-J51_EN.indb 1 10.8.19 2:50:43 PM10.8.19 2:50:43 PM

2

Warnings, Cautions and Others

CAUTION

• Do not block the ventilation openings or

holes.

(If the ventilation openings or holes are

blocked by a newspaper or cloth, etc., the

heat may not be able to get out.)

• Do not place any naked  ame sources, such

as lighted candles, on the apparatus.

• When discarding batteries, environmental

problems must be considered and local

rules or laws governing the disposal of these

batteries must be followed strictly.

• Do not expose this apparatus to rain,

moisture, dripping or splashing and that

no objects  lled with liquids, such as vases,

shall be placed on the apparatus.

CAUTION

Excessive sound pressure from earphones or

headphones can cause hearing loss.

CAUTION:

Battery shall not be exposed to excessive heat

such as sunshine,  re, or the like.

CAUTION

The button in any position does not disconnect

the mains line.

Disconnect the mains plug to shut the power o

completely (the STANDBY lamp goes o ).

The MAINS plug or an appliance coupler is used as

the disconnect device, the disconnect device shall

remain readily operable.

• When the System is on standby, the STANDBY

lamp lights red.

• When the System is turned on, the STANDBY

lamp goes o .

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks,  re, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or

moisture.

IMPORTANT FOR LASER PRODUCTS

(For countries/areas other than U.S.A. and Canada)

1. CLASS 1 LASER PRODUCT

2.

CAUTION: Do not open the top cover or

cabinet. There are no user serviceable parts

inside the unit; leave all servicing to quali ed

service personnel.

3.

CAUTION: Visible and/or invisible class 1M

laser radiation when open. Do not view

directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL,

PLACED INSIDE THE UNIT.

For U.S.A. and Canada, please refer to

the attached sheet “Warnings, Cautions,

and Others” and “Important Safety

Instructions” before using the System.

UX-J51_EN.indb 2UX-J51_EN.indb 2 10.8.19 2:50:44 PM10.8.19 2:50:44 PM

3

Caution: Proper Ventilation

To avoid risk of electric shock and  re, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/ Back: No obstructions should be placed in the areas indicated by the dimensions in the

illustration.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a

stand with a height of 10 cm (3-15/16 in.) or more.

Attention: Ventilation Correcte

Pour éviter tout risque de choc électrique et d’incendie, placez l’appareil en respectant ce qui suit:

1. Avant: Rien ne doit gêner le dégagement.

2. Flancs/Dessus/Arrière: Aucun obstacle ne doit être placé dans les zones indiquées par les

dimensions dans l’illustration.

3. Dessous: Poser l’appareil sur une surface plate. Laissez su samment d’espace pour que la

ventilation puisse s’e ectuer correctement en plaçant l’appareil sur un socle d’une hauteur de 10

cm ou plus.

Front view

Vue avant

Side view

Vue latérale

[European Union Only]

Main unit

Appareil principal

Main unit

Appareil principal

Speaker

Enceinte

Speaker

Enceinte

UX-J51_EN.indb 3UX-J51_EN.indb 3 10.8.19 2:50:44 PM10.8.19 2:50:44 PM

What the UX-J51 Can Do

Various recording formats

Disc Playback

As well as music CDs, the system will also play discs containing recorded audio files (MP3/

WMA).

High-quality sound reproduction of iPod music

iPod Playback Function

With this system, the amplifier receives digital signals of iPod music as input. This

realizes the reproduction of high-quality sound minimizing the deterioration of sound

quality.

Supports for USB connection, analog input and digital input

External Input

The system supports the playback of a USB flash memory and USB mass storage class

compliant digital audio player. In addition, as well as analog input terminals for cassette

decks, the UX-J51 also features a sampling rate converter compliant digital input

terminal for digital tuners etc.

Choose your favorite audio quality

Digital Signal Processor Function

This includes “TONE”, which you can use to select detailed audio characteristics for the

low-, mid- and high-range bands, as well as “D-BASS” which allows you to adjust super-

bass effect.

4

UX-J51_EN.indb 4UX-J51_EN.indb 4 10.8.19 2:50:45 PM10.8.19 2:50:45 PM

5

Contents

Procedures by

Input Source

Maintenance

P. 2 3

P.63

Be sure to read these precautions.

Warnings, Cautions and Others ………… 2

Accessories ……………………………… 6

Installing the System …………………… 7

Connecting the System ………………… 8

Component Names and Functions … 12

How to Use This Manual ……………… 16

Basic Operation ……………………… 18

Important Information ……………… 20

Before Using the

System

This chapter explains how to connect and use

the system with the different input sources.

• CD

• Receiving Radio Broadcasts

• iPod

• USB

• External Components

• D.AUDIO

This chapter explains how to store and

maintain your system so that it continues to

give pleasure for many years to come.

Audio Settings

P.43

This chapter explains how to tailor the system

to your audio preferences.

• CONEQ (Acoustic Equalizer)

• Digital Signal Processor

• BALANCE

Component

Settings

P.53

This chapter explains how to select the settings

for the system.

• Setting the Timer

• Display Settings

To ensure safety, read the items by this

mark carefully.

• Care and Storage

• Specifications

• Setting the System Clock

• Auto Power Save (A.P.S.)

• Setting the Power Supply

• Messages

• Troubleshooting

• Glossary of Terms

UX-J51_EN.indb 5UX-J51_EN.indb 5 10.8.19 2:50:46 PM10.8.19 2:50:46 PM

6

AM loop antenna (1) FM indoor antenna (1)

Remote control (1)

Batteries for

Remote control

(R03: 2)

Check that all accessories are present in the package

Accessories

Speaker cords (2 m [6.56 ft.]: 2)

If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer

immediately. If the unit was shipped to you directly, notify your shipper immediately. JVC recommends

that you retain the original carton and packing materials in case you need to move or ship the unit in

the future. Keep this manual handy for future reference.

RM-SUXJ51U

Do not damage the cable by applying

excessive force when winding.

l

5 cm

(2 in.)

USB cable (not supplied)

Core  lter (1)

How to attach the core filter to the USB cable

Attach the core filter to the USB cable to reduce interference.

Stopper

Release the stopper of the core filter.

Run the cable through the core filter, and

wind firmly once inside the cutout of the

core filter as shown in the illustration.

Close the core filter until it clicks shut.

3

2

1

UX-J51_EN.indb 6UX-J51_EN.indb 6 10.8.19 2:50:46 PM10.8.19 2:50:46 PM

7

Always install the system on a flat, stable surface. When installing the system on a stand of some sort, be

sure to check the strength of the stand.

The magnets used in the speakers may cause color irregularities on TV or PC screens. Do not set up the

speakers too close to a TV or PC.

l

Notes on installing the system

The sound will vary depending on the positioning of the speakers. To get the best possible sound quality,

note the guidelines below.

Ensure that the areas around the left and right speakers are as identical as possible. Set up the left

and right speakers away from the wall and hang thick curtains on any windows to minimize echoes or

reverberation.

Place the left and right speakers as far apart as possible.

Position the speakers at the same height as your ears when you are using the system.

l

Getting the best acoustic effect

Observe the following cautions when installing the system. Insufficient heat

radiation may build up internal heat and cause a malfunction or fire hazard.

Do not place any object on the system that may hinder heat radiation.

Do not place the system upside-down or lay it on its side.

Do not cover the system with a cloth or place it on a carpet or blanket.

Do not place the system in a narrow space that hinders the ventilation.

Leave the spaces specified below around the cabinets of the main unit.

Top panel: 50 cm (19-11/16 in.) or more

Side panel: 10 cm (3-15/16 in.) or more

Back panel: 10 cm (3-15/16 in.) or more

Install the system so the power outlet is easily accessible, and unplug the power

cord from the power outlet immediately in case of any trouble.

Note that the power supply to the system is not shut down completely by simply

setting the power switch to OFF.

To shut down the power supply completely, unplug the power cord.

l

Left speaker Right speakerMain unit

CAUTION

Installing the System

UX-J51_EN.indb 7UX-J51_EN.indb 7 10.8.19 2:50:47 PM10.8.19 2:50:47 PM

8

Main Connections

Connecting the System

To AC wall outlet

Push into the slot.

AM loop antenna

1

Connect to [FM75].

2

Find the location that gives

the best reception.

3

Fix the antenna in place.

FM indoor antenna

AC power cord

Right speaker

Left speaker

Ensure that all the cords are securely connected. Loose or incomplete

connections may result in noise interference or no sound at all.

For more information,

see “Connecting

Other Accessories

(Commercially Available

Units)” on P.10-11.

Insert the plug

firmly all the way

into the AC wall

outlet.

l

Caution for

Connection

Do not plug the AC power cord into an AC wall outlet until all the connections are

completed. Before disconnecting any cords or cables, always turn the system off and

unplug the power cord from AC wall outlet.

Caution for outdoor antenna

installation

Since antenna installation requires skill and experience, always

consult your dealer before installation. The antenna should be

located away from power lines. If the antenna falls over, contact

with a power line creates the risk of electric shock.

The speakers are

not distinguished as

either the left or right

speaker.

Directly point to the

location and direction

that give the best

reception.

UX-J51_EN.indb 8UX-J51_EN.indb 8 10.8.19 2:50:47 PM10.8.19 2:50:47 PM

9

Connecting the System

The antenna supplied with the system is a basic antenna for indoor use. For stable signal

reception, the use of an outdoor antenna (commercially available) is recommended. To

connect an outdoor antenna, first remove the indoor antenna.

Connecting the FM indoor antenna

Preparing the ends of the speaker cords

Twist the plastic sleeve on the end of the cord as

you pull it off.

l

Notes on connecting the

speaker cords

Never short-circuit the positive (+) and negative (–) ends

of the speaker cords. (Do not touch the + and - cords

together.) Mistakenly reversing the positive and negative

polarity will result in unnatural sound and unclear sound.

Connecting the speakers

Microcomputer malfunctions

If the system is connected correctly and still does not

operate normally or shows display errors, reset the

microcomputer. (P.67)

The antenna supplied with the system is for indoor use. Place it as far as possible away from

the main unit, your TV set, the speaker cords and the power cord and point it in the direction

that gives the best reception.

Connecting the AM loop antenna

123

Connecting the antenna cord

As shown on the right, connect the AM

antenna cord [AM] terminals.

l

1234

Connecting the speaker cords to the speaker

l

Connecting the speaker cords to the main unit

l

UX-J51_EN.indb 9UX-J51_EN.indb 9 10.8.19 2:50:47 PM10.8.19 2:50:47 PM

10

Connecting Other Accessories (Commercially Available Units)

Connecting the System

When connecting a related system component, read the instruction manual that comes with the

component too.

Ensure that all the cords are securely connected. Loose or incomplete connections may result in noise

interference or no sound at all.

l

D.AUDIO IN

Connect digital audio players to the

[D.AUDIO IN]

terminal on the rear panel of the main unit.

Portable digital audio players can be connected

using a 3.5 mm (1-7/16 in.) stereo mini-plug cable

(commercially available).

When you are not using the digital audio player,

unplug the mini-plug cable from the main unit.

[D.AUDIO IN]

terminal inputs an analog audio signal.

l

SPEAKERS

DIGITAL OUT

DIGITAL IN

D.AUDIO

IN

REC OUT

PLAY IN

SUB

WOOFER

PRE OUT

R

L

R

D.AUDIO

IN

Digital

audio

player

iPod

Attach the Dock adapter supplied with iPod to the

system.

Open the cover on the main unit, and then push

down the Dock adapter into the unit with its slit

facing toward the unit until it clicks.

USB

Connect USB flash memory or USB mass storage class

compliant digital audio players to the [USB ] port

after opening the cover on the main unit.

Depending on the device being connected, it may

take some time for the system to recognize it.

Some USB devices may not be recognized or cannot

play certain files.

With some models, a USB connection mode selection

screen will appear. Select “Storage Mode”.

l

For more information on which models can be connected, see P.34.

USB

Attach iPod to the

iPod connector.

You cannot attach iPod to the system if it is in

a cover, case, or with other accessories. Always

remove it.

Connecting iPod to the system without using

the Dock adapter may deteriorate or damage the

connector. Always use the Dock adapter.

Keep iPod on a straight position while connecting/

disconnecting it.

Once iPod is connected, it can be charged.

l

Digital

audio

player

USB

flash

memory

To remove the Dock adapter

l

Insert a flat-blade

screwdriver or a similar

tool into the slit of the

Dock adapter, and then

remove it upward.

UX-J51_EN.indb 10UX-J51_EN.indb 10 10.8.19 2:50:48 PM10.8.19 2:50:48 PM

11

Connecting the System

SUB WOOFER PRE OUT

Connect a subwoofer with a built-

in amplifier to the

[SUB WOOFER

PRE OUT]

terminal on the rear

panel of the main unit.

Be sure to connect a subwoofer

with the same speaker impedance.

l

SPEAKERS

SUB

WOOFER

PRE OUT

DIGITAL OUT

REC OUT

PLAY IN

D.AUDIO

IN

DIGITAL IN

R

L

SUB

WOOFER

PRE OUT

PHONES

Plug headphones equipped with

a 3.5 mm (1-7/16 in.) stereo mini-

plug into the

[PHONES]

jack on the

front panel of the main unit.

DIGITAL OUT (OPTICAL)(PCM signals)

SPEAKERS

SUB

WOOFER

PRE OUT

DIGITAL OUT

REC OUT

PLAY IN

D.AUDIO

IN

DIGITAL IN

R

L

DIGITAL OUT

Digital audio component

Optical digital input

(PCM signals)

Connect the optical digital input

terminals on a digital audio

component to the

[DIGITAL OUT

(OPTICAL)]

terminal on the rear

panel of the main unit.

AUX REC OUT

SPEAKERS

R

L

SUB

WOOFER

PRE OUT

DIGITAL OUT

DIGITAL IN

REC OUT

PLAY IN

D.AUDIO

IN

REC OUT

Audio IN

Connect the audio IN terminals

on components such as cassette

decks to the

[AUX REC OUT]

terminal on the rear panel of the

main unit.

[AUX REC OUT]

outputs an

analog audio signal.

l

AUX IN

SPEAKERS

DIGITAL OUT

DIGITAL IN

REC OUT

PLAY IN

D.AUDIO

IN

SUB

WOOFER

PRE OUT

R

L

R

L

PLAY IN

R

L

Cassette deck, etc.

Audio OUT

Connect the audio OUT terminals

on components such as cassette

decks to the

[AUX PLAY IN]

terminal

on the rear panel of the main unit.

[AUX PLAY IN]

inputs an analog

audio signal.

l

Powered subwoofer

DIGITAL IN (OPTICAL)(PCM signals)

SPEAKERS DIGITAL OUT

REC OUT

PLAY IN

DIGITAL IN

SUB

WOOFER

PRE OUT

D.AUDIO

IN

R

L

DIGITAL IN

Optical digital output

(PCM signals)

Connect the optical digital output

terminals on components such as digital

tuners to the

[DIGITAL IN (OPTICAL)]

terminal on the rear panel of the main

unit.

Set the digital audio output on

connected components to “PCM”.

l

Digital tuner, etc.

Cassette deck, etc.

CAUTION

Excessive sound pressure

from earphones or

headphones can cause

hearing loss.

UX-J51_EN.indb 11UX-J51_EN.indb 11 10.8.19 2:50:48 PM10.8.19 2:50:48 PM

USB

U

S

B

12

Main unit

Standby Mode

While the

[STANDBY/TIMER]

indicator on the main

unit is lit, the system is using very weak current

to maintain the built-in memory. This is called

Standby mode. When system main unit is in this

mode, you can turn it on using the remote control.

One-touch Operation

This system features a convenient one-touch

operation function. In Standby mode, pressing

any of the following keys will turn on system

power:

[TUNER/BAND], [CD

E

], [iPod

E

],

[USB

E

], [D.AUDIO], [D-IN]

, or

[AUX]

of the

remote control.

Component Names and Functions

Power (P.19)

Turns the system on or o (Standby).

STANDBY/TIMER indicator

Red: Lights in normal Standby mode.

Orange: Lights in Timer Standby

mode.

Display (P.13)

L

CD tray open/close

(P.19, 24)

VOLUME (P.18 )

E

/BAND (P.19)

INPUT SELECTOR (P.19)

PHONES jack (P.11)

Remote sensor (P.15)

F

/TUNING MODE (P.31)

G

/

I

,

J

/

H

(P.31, 35, 37)

CD tray (P.19, 24)

Dial lighting (P.59)

Cover

USB port (P.10, 36)

iPod connector (P.10, 34)

Open the cover before

attaching iPod or USB device.

UX-J51_EN.indb 12UX-J51_EN.indb 12 10.8.19 2:50:49 PM10.8.19 2:50:49 PM

13

Display

Displays shown in this manual

may di er from the actual displays.

Component Names and Functions

Shows numbers and text.

AUTO

Lights during auto tuning. Turns o during manual tuning. (P.31)

TUNED

Lights when you are tuned to the radio station. (P.31)

ST.

Lights when you are receiving the stereo broadcast. (P.31)

Flashes when the

sound is muted.

(P.18)

Lights when the audio  le folder is displayed.

kHz

Displays the AM reception frequency.

MHz

Displays the FM reception frequency.

Lights during

playback. (P.24, 36)

Lights when there is the disc

in the CD tray. (P.24)

Lights when

playback is paused.

(P.25, 35, 37)

Displayed while

the sleep timer

is set. (P.54)

Displayed while

the program

timer is set.

(P.55)

Lights in program playback mode. (P.28)

Lights in random playback mode. (P.27)

Lights during CD/USB all-tracks repeat playback. (P.27, 37)

The message “1” is also displayed during single-track repeat

playback. (P.27, 37)

Lights when settings, such as the sound

quality, are completed.

A.P.S.

Lights when Auto Power Save (A.P.S.) is set. (P.61)

TONE

Lights when a TONE is set. (P.47)

D-BASS

Lights when a super-bass (D-BASS) level is selected.

(P.46)

Lights during USB connection. (P.36)

Lights during iPod connection. (P.34)

Lights when a track is displayed.

Displayed during stop

of CD playback while

the total elapsed time is

displayed.

Lights in folder playback mode. (P.37)

UX-J51_EN.indb 13UX-J51_EN.indb 13 10.8.19 2:50:50 PM10.8.19 2:50:50 PM

Clears settings. (P.29)

Display settings.

(P.59)

Switches the information

shown on the display.

(P.25, 31, 35, 37)

Sets the shu e of iPod.

(P.35)

14

Remote control

Remote control keys with the same names as keys on the

main unit have the same functions as the main unit keys.

Component Names and Functions

Selects tracks or

radio stations.

(P.25, 30-32, 35, 37)

Numbers

Selects tracks or radio

stations.

(P.25, 28-30, 33)

Selects input source.

(P.38, 39)

CD tray open/close

(P.19, 24)

Sets the timer.

(P.54-58)

Turns the unit on or o (Standby).

(P.19, 58)

Turns the main unit on when the

[STANDBY/TIMER] indicator on the

main unit is lit.

Selects folders or albums.

(P.35, 37)

Selects the playback mode.

(P.27-29, 35, 37)

Adjusts volume. (P.18, 38)

Stops the playback.

Selects the radio station selection

mode. (P.25, 27, 28, 31, 58)

Skips back or forward through the

tracks and selects the radio station.

(P.25, 31, 37)

Sets the sound quality.

(P.46-51)

Selects input source.

Starts playback.

(P.19, 24, 29, 30, 34-37, 42)

ENTER

Fixes a setting.

Selects a setting.

Uses for several settings.

UX-J51_EN.indb 14UX-J51_EN.indb 14 10.8.19 2:50:50 PM10.8.19 2:50:50 PM

15

Loading the remote control batteries

1

Remove the

battery cover.

2

Load the AAA-size batteries

supplied with the system.

3

Close the

battery cover.

Check the polarity of

the batteries (

UV

)

when loading them.

l

The batteries supplied with the system are for operational testing and may last only for a short time.

When replacing the batteries, always load 2 new batteries.

l

Component Names and Functions

Using the remote control

After plugging the main unit into an AC

wall outlet, press the power [ ] key

on the remote control unit to turn the

system on.

After the system powers up, press the

key for the function you want to use.

Point the remote control at the remote

sensor when using it.

The remote control may not operate

correctly if direct sunlight or light

from a high-frequency fluorescent

lamp (such as an inverter type) is

shining on the remote sensor. If

this happens, move the system to a

different location to avoid this type

of malfunction.

l

Approx.

6 m

(19.68 ft.)

Approx.

30

°

Approx.

30

°

CAUTION

Do not leave the battery near fire or under direct sunlight. A fire, explosion

or excessive heat generation may result.

If the range or effectiveness of

the remote control decreases,

replace both batteries.

l

UX-J51_EN.indb 15UX-J51_EN.indb 15 10.8.19 2:50:51 PM10.8.19 2:50:51 PM

16

While this system can be controlled from either the remote control or the main unit, the explanations

in this manual primarily describe operation procedures using the remote control.

Operation procedure

How to Use This Manual

The displays shown in this

instruction manual may differ from

the actual displays.

l

Display shown during or

after an operation

Remote control keys used

in the procedure

UX-J51_EN.indb 16UX-J51_EN.indb 16 10.8.19 2:50:51 PM10.8.19 2:50:51 PM

17

Explains the procedure for CDs.

Operation icons

How to Use This Manual

Explains the procedure for the

radio.

Related functions that

may also be helpful

Explanations of remote

control procedures

Explanations of main unit

procedures

Explains the procedures for

iPods.

Explains the procedure for

digital audio players.

Explains the procedures for

USB devices.

Explains the procedures for

external components.

Explains how to set the

sound quality.

Explains how to set up

component units.

Explains how to carry out

system maintenance.

UX-J51_EN.indb 17UX-J51_EN.indb 17 10.8.19 2:50:51 PM10.8.19 2:50:51 PM

18

Basic Operation

Preparations

Check the connections. (P.8-11)

Have the remote control ready. (P.15)

Increases the

volume

Lowers the

volume

Lowers the volume

Increases the volume

Mute

n

Press this key again to unmute the sound.

l

1

3

This section describes some basic procedures for using the system, such as tuning the radio and playing

audio from a CD, iPod, USB device, a digital audio player.

3

1

2

Adjusting the volume level

n

2

UX-J51_EN.indb 18UX-J51_EN.indb 18 10.8.19 2:50:52 PM10.8.19 2:50:52 PM

19

Basic Operation

On remote control

[D.AUDIO], [TUNER/BAND],

[CD

E

], [iPod

E

], [USB

E

], [D-IN],

[AUX]

key also turn on the power.

Pressing the power [

] key when the

system is on turns it off (Standby mode).

l

22

Insert a disc (when listening to a CD).

To use other components for playback, proceed to step 3.

Close the tray.

Open the tray.

Insert a CD with the label

side upwards.

Insert a CD.

Press the [

L

] key.

33

Start playback.

You can select the sound quality you want. See <Audio Settings> (P.43-52) for details.

l

Press the Play/Pause key for the input source. See <Procedures by Input Source> (P.23-42)

for details.

Turn the system on (o ).

11

UX-J51_EN.indb 19UX-J51_EN.indb 19 10.8.19 2:50:52 PM10.8.19 2:50:52 PM

20

Discs must be finalized during writing.

Depending on the equipment or recording mode

used for recording onto a CD-R or CD-RW disc, and

depending on the type of CD-R or CD-RW disc used,

you may not be able to play the disc on this system.

l

You may not be able to play discs that do not conform

to the CD standard, such as Copy Control CDs.

l

You cannot connect a computer and JVC Everio

camcorder to the USB terminals of the System.

Electrostatic shock at connecting a USB device may

cause abnormal playback of the device. In this case,

disconnect the USB device then turn off this unit.

When connecting with a USB cable, use the USB 2.0

cable whose length is less than 1 m (3.28 ft.).

You can connect a USB device such as a USB flash

memory device, hard disk drive, multimedia card reader,

etc. to this System.

l

Important Information

Supported Media

USB mass storage class

compliant digital audio

player

CD-R/CD-RW discs

recorded in CD-DA

format

MP3/WMA  les

recorded on CD-R/CD-

RW discs

ExplanationMedia

Icon in this

manual

Precautions when writing data to media

Discs recorded in Packet Write mode or UDF (Universal Disc Format) cannot be played.

When writing data to a disc, always close the session or finalize the disc. The disc may not play properly if

you do not close the session or finalize the disc.

Depending on the specifications of the writing software used, the recorded folder names and file names

may not be displayed correctly.

Playback for multi-session discs or discs that contain large numbers of folders may take longer to begin

than for normal discs.

If you write audio files and music CD tracks (CD-DA format) to the same disc, the disc may not play

correctly.

Before writing audio files to a disc, check that the files play back correctly on the PC being used to write the

files.

After you finish writing, check that the written files are played back correctly.

Use the correct file extensions (mp3, wma, m4a) in the names of audio files. Files without file extensions

will not play. Also, do not use audio file extensions (mp3, wma, m4a) for files that are not audio files.

For more information on file extensions, see <Supported Audio Files> on the right.

In this manual, MP3, WMA and AAC files are referred to collectively as “audio files”.

l

USB  ash memory

USB

Commercially available

music CDs

CD

UX-J51_EN.indb 20UX-J51_EN.indb 20 10.8.19 2:50:53 PM10.8.19 2:50:53 PM

Page is loading ...

JVC GVT0294-006B User manual

This manual is also suitable for

JVC GVT0294-006B User manual

Related papers

Other documents