Turbosound TSB-110 User manual

Turbosound
Brand
Turbosound
Model
TSB-110
Category
Speaker sets
Type
User manual

Turbosound TSB-110 is a general purpose band-pass subwoofer designed to add low frequency reinforcement to Turbosound loudspeakers. It utilizes a dual voice-coil 10” low frequency driver with two configurable 4 ohm voice coils. The TSB-110 can be configured as a single 8 ohm sub-bass unit if required by effectively patching the two voice coils in series. It has a built-in high pass crossover network at 150Hz, and its frequency response ranges from 45Hz to 180Hz. The TSB-110 is capable of handling 300 watts RMS, 600 watts program power, and has a sensitivity of 95dB, 1 watt @ 1meter.

Turbosound TSB-110 is a general purpose band-pass subwoofer designed to add low frequency reinforcement to Turbosound loudspeakers. It utilizes a dual voice-coil 10” low frequency driver with two configurable 4 ohm voice coils. The TSB-110 can be configured as a single 8 ohm sub-bass unit if required by effectively patching the two voice coils in series. It has a built-in high pass crossover network at 150Hz, and its frequency response ranges from 45Hz to 180Hz. The TSB-110 is capable of handling 300 watts RMS, 600 watts program power, and has a sensitivity of 95dB, 1 watt @ 1meter.

TSB-110
SUB-BASS LOUDSPEAKER
QUICK START GUIDE
Turbosound Ltd.
Star Road, Partridge Green
West Sussex RH13 8RY England
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155
web: www.turbosound.com
Version 1.1 ©Turbosound 8/2008
quick start
TSB-110
TSB-110 quick start guide
Page 2
TSB–110 CONFIGURATIONS
The TSB-110 is a general purpose band-pass subwoofer designed to add low frequency
reinforcement to Turbosound loudspeakers such as the IMPACT50, IMPACT80, TCS-30, TCS-35,
TXD-081 and TQ-308.
The TSB-110 utilises a dual voice-coil 10” low frequency driver with two configurable 4 ohm voice
coils. In its ‘as shipped’ configuration the two inputs and two outputs are set up so that the bass
cabinet can be driven by the left and right channel of a standard two channel (stereo) power
amplifier. The input connections are labelled left and right on the spring terminals and are also
present at the 1+, 1- (left) and 2+, 2- (right) connections on the Speakon NL4MP socket. Outputs are
available through the spring terminals only.
The inputs drive the two voice coils separately via a 150hz low-pass first order filter. The satellite
speaker outputs are provided via a high-pass first order filter at 150Hz.
Amplifier considerations
Turbosound speaker enclosures should be driven by high quality power amplifiers designed for
true professional use. Such amplifiers will have balanced inputs, DC and RF fault protection, and
well designed cooling systems for reliability. Turbosound power amplifiers such as the T-45 and T-
25 are recommended for this purpose.
The program power listed in the loudspeaker’s technical specification is the best guide to the size
of amplifier required for general purpose applications. The amplifier should therefore be capable
of delivering long term broadband power equal to the loudspeaker’s program power rating at the
loudspeaker’s stated nominal impedance. This approach allows sufficient headroom to generate
good dynamic range.
In general, the more powerful the amplifier, the better it will sound, provided that it is not driven
into sustained clipping. It should be understood that overdriving an insufficiently powered
amplifier is more likely to cause loudspeaker damage – the total energy in a heavily clipped signal
is far higher than in an unclipped signal – than operating a more powerful amplifier within its
ratings.
RECOMMENDED AMPLIFIER POWER RATINGS:
The amplifier's rated r.m.s. continuous power output (20Hz – 20kHz, each
channel) should be 2 x 300 watts at 4 ohms per channel.
Single coil (8 ohm) configuration
The TSB-110 can be configured as a single 8 ohm sub-bass unit if required by effectively patching
the two voice coils in series. To do this, remove the connector dish housing the spring terminals
by removing the six cross-head fixing screws and lifting it out and away from the cabinet as far as
the internal wiring will allow.
quick start
TSB-110
TSB-110 quick start guide
Page 3
Locate the four jumper locations on the circuit board, labelled J1, J2, J3, and J4. The unit is
shipped with J2 and J4 connected with J1 and J3 not connected (dual 4 ohm mode). For single 8
ohm operation unplug J2 and J4 and transfer the jumpers to J1 and J3. This connects the two
voice coils in series and transfers the input to the left input only (pins 1+ and 1- on the Speakon
NL4MP). Note: In single coil mode DO NOT use the right inputs and outputs as this will result in
incorrect operation and may damage loudspeakers and amplifiers.
Technical Specifications
Dimensions 330mm x 585mm x 330mm (13” x 23” x 13”)
Net weight 16.5 kg (36.3 lbs)
Frequency Response 45Hz to 180Hz
Power Handling 300 watts r.m.s., 600 watts program
Nominal Impedance 2 x 4 ohms
Sensitivity 95dB, 1 watt @ 1metre
Calc. Max SPL 120dB continuous, 126dB peak
Crossover Built-in high pass crossover network at 150Hz
Construction 15mm (5/8”) birch plywood
Rigging 4 x M10 internal rigging points
Options TurboBlue or white semi-matt textured paint
Spares & Accessories LS-1019.2 10” LF driver (requires M5 x 35 fixing bolts)
RC-1019.2 recone kit
J1
J2
J3
J4
TSB-110 Configured for 8 ohms
TSB-110 Configured for 2 x 4 ohms
J4
J3
J2
J1
quick start
TSB-110
TSB-110 quick start guide
Page 4
WARRANTY
Limited Warranty
This Turbosound loudspeaker product is warranted to the original end-user purchaser and all
subsequent owners for a period of two (2) years for loudspeakers from the original date of
purchase.
Warranty Coverage
Warranty coverage includes defects in materials and workmanship. It does not include:
• damage caused by accident, misuse, abuse, neglect or modification by any person other
than an authorised Turbosound representative,
• damage caused by failure to operate the product in accordance with the instructions
contained in the user manual,
• damage occurring during shipment in transit,
• claims based on any misrepresentation by the seller,
• products which do not have the original components as specified in the product
engineering information,
• products on which the serial number has been removed or defaced.
Shipping
Should any fault develop with a component of your Turbosound system, please return the
product, freight pre-paid, in its original packing carton, along with proof of purchase such as the
original bill of sale or receipted invoice, and a description of the suspected fault to Turbosound
Ltd. (Att: Customer Service), or your local authorised Turbosound representative. The product
serial number must be quoted in all correspondence relating to the claim. Insurance is
recommended, as Turbosound or its representatives are not liable for loss or damage in transit.
Turbosound will pay for return freight costs should repairs be covered under warranty.
Turbosound Ltd., Star Road, Partridge Green, West Sussex RH13 8RY UK
Turbosound Ltd., Star Road, Partridge Green, West Sussex RH13 8RY UKTurbosound Ltd., Star Road, Partridge Green, West Sussex RH13 8RY UK
Turbosound Ltd., Star Road, Partridge Green, West Sussex RH13 8RY UK
t: +44 (0)1403 711447 f
t: +44 (0)1403 711447 ft: +44 (0)1403 711447 f
t: +44 (0)1403 711447 f: +44 (0)1403 710155 www.turbosound.com
: +44 (0)1403 710155 www.turbosound.com: +44 (0)1403 710155 www.turbosound.com
: +44 (0)1403 710155 www.turbosound.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Turbosound TSB-110 User manual

Turbosound
Brand
Turbosound
Model
TSB-110
Category
Speaker sets
Type
User manual

Turbosound TSB-110 is a general purpose band-pass subwoofer designed to add low frequency reinforcement to Turbosound loudspeakers. It utilizes a dual voice-coil 10” low frequency driver with two configurable 4 ohm voice coils. The TSB-110 can be configured as a single 8 ohm sub-bass unit if required by effectively patching the two voice coils in series. It has a built-in high pass crossover network at 150Hz, and its frequency response ranges from 45Hz to 180Hz. The TSB-110 is capable of handling 300 watts RMS, 600 watts program power, and has a sensitivity of 95dB, 1 watt @ 1meter.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents