Sharp 36-250 User manual

Brand: Sharp

Model: 36-250

Category: Microwaves

Type: User manual

This manual is also suitable for

R-370EZ

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO

AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY...................INSIDE FRONT COVER

BEFORE SERVICING ......................................................................................................INSIDE FRONT COVER

WARNING TO SERVICE PERSONNEL................................................................................................................1

MICROWAVE MEASUREMENT PROCEDURE ...................................................................................................2

FOREWORD AND WARNING...............................................................................................................................3

PRODUCT DESCRIPTION....................................................................................................................................4

OVEN SCHEMATIC...............................................................................................................................................4

PARTS LIST ..........................................................................................................................................................5

SERVICE INFORMATION .....................................................................................................................................7

PACKING AND ACCESSORIES .........................................................................................................................10

S9125R370EPZ/

MICROWAVE OVEN

MODEL

R-370EZ

In the interest of user-safety the oven should be restored to its original

condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens con-

tain circuitry capable of producing very high voltage and

current, contact with following parts may result in a severe,

possibly fatal, electrical shock. (High Voltage Capacitor, High

Voltage Power Transformer, Magnetron, High Voltage Rectifier

Assembly, High Voltage Harness etc..)

SHARP CORPORATION

This document has been published to be used for after

sales service only.

The contents are subject to change without notice.

SUPPLEMENTAL SERVICE MANUAL

This is a supplemental Service Manual for Model R-370EZ. This model is quite similar to base

model R-370EK. Use this supplemental manual together with the Base Model Service Manual

(Refer No. is S4112R370EPS/) for complete operation, service information, etc..

Popcorn

Rice

Clock

Frozen

Fish

Seafood

Breast

12345

67890

R-370EZ

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE

EXPOSURE TO EXCESSIVE MICROWAVE

ENERGY

(a) Do not operate or allow the oven to be operated with the door open.

(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)

seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and

latches, (5) evidence of dropping or abuse.

compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,

integrity, and connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave

generation and transmission systems shall be repaired, replaced, or adjusted by procedures described

in this manual before the oven is released to the owner.

(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be

performed on each oven prior to release to the owner.

BEFORE SERVICING

Before servicing an operative unit, perform a microwave emission check as per the Microwave

Measurement Procedure outlined in this service manual.

If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS

CORPORATION immediately @1-800-237-4277.

If the unit operates with the door open, service person should 1) tell the user not to operate the oven

and 2) contact SHARP ELECTRONICS CORPORATION and The Food and Drug Administration's

Center for Devices and Radiological Health immediately.

Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit

found with emissions in excess of 4mW/cm

. The owner of the unit should be instructed not to use

the unit until the oven has been brought into compliance.

R-370EZ

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of pro-

ducing very high voltage and current, contact with

following parts

may result in a severe, possibly

fatal, electrical shock.

(Example)

High Voltage Capacitor, High Voltage Power Trans-

former, Magnetron, High Voltage Rectifier Assem-

bly, High Voltage Harness etc..

Read the Service Manual carefully and follow all

instructions.

Before Servicing

1. Disconnect the power supply cord , and then

remove outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

WARNING:RISK OF ELECTRIC SHOCK.

DISCHARGE THE HIGH-VOLTAGE

CAPACITOR BEFORE SERVICING.

The high-voltage capacitor remains charged about 60

seconds after the oven has been switched off. Wait for 60

seconds and then short-circuit the connection of the high-

voltage capacitor (that is the connecting lead of the high-

voltage rectifier) against the chassis with the use of an

insulated screwdriver.

Whenever troubleshooting is performed the power supply

must be disconnected. It may, in some cases, be necessary

to connect the power supply after the outer case has been

removed, in this event,

1. Disconnect the power supply cord, and then remove

outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the leads to the primary of the power

transformer.

5. Ensure that the leads remain isolated from other

components and oven chassis by using insulation tape.

6. After that procedure, reconnect the power supply cord.

When the testing is completed,

1. Disconnect the power supply cord, and then remove

outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Reconnect the leads to the primary of the power

transformer.

5. Reinstall the outer case (cabinet).

6. Reconnect the power supply cord after the outer case is

installed.

7. Run the oven and check all functions.

After repairing

1. Reconnect all leads removed from components during

testing.

2. Reinstall the outer case (cabinet).

3. Reconnect the power supply cord after the outer case is

installed.

4. Run the oven and check all functions.

Microwave ovens should not be run empty. To test for the

presence of microwave energy within a cavity, place a cup

of cold water on the oven turntable, close the door and set

the power to HIGH and set the microwave timer for two (2)

minutes. When the two minutes has elapsed (timer at zero)

carefully check that the water is now hot. If the water

remains cold, carry out Before Servicing procedure and re-

examine the connections to the component being tested.

When all service work is completed and the oven is fully

assembled, the microwave power output should be checked

and a microwave leakage test should be carried out.

Don't Touch !

Danger High Voltage

R-370EZ

MICROWAVE MEASUREMENT PROCEDURE

A. Requirements:

1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven

should not exceed 1mW/cm

at any point 5cm or more from the external surface of the oven, measured prior to acquisition

by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm

at any point 5cm or more from the external

surface of the oven.

2) Safety interlock switches:

Primary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of the requirement

as above mentioned, secondary interlock switch shall prevent microwave radiation emission in excess of 5 mW/cm

any point 5cm or more from the external surface of the oven.

B. Preparation for testing:

Before beginning the actual measurement of leakage, proceed as follows:

1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.

Important:

Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard

for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.

2) Place the oven tray in the oven cavity.

3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.

The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and

made of an electrically nonconductive material such as glass or plastic.

The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage

is measured accurately.

4) Set the cooking control on Full Power Cooking Mode

5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,

replace it with 275 ml of cool water.

C. Leakage test:

Closed-door leakage test (microwave measurement)

1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.

2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the

meter.

3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal

has been breached (eg., around the switches, indicator, and vents).

While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed

latch assembly.

4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm

NOTE: After servicing, record data on service invoice and microwave leakage report.

R-370EZ

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH,

NEW JERSEY 07430-2135

SERVICE MANUAL

MICROWAVE OVEN

R-370EZ

FOREWORD

This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service

Information for the SHARP MICROWAVE OVEN, R-370EZ.

The model R-370EZ is quite similar to base model R-370EK (Refer No. is S4112R370EPS/).

It is recommended that service personnel carefully study the entire text of this manual and the base model's manual so that

they will be qualified to render satisfactory customer service.

Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and

microwave radiation hazard.

WARNING

Never operate the oven until the following points are ensured.

(A) The door is tightly closed.

(B) The door brackets and hinges are not defective.

(D) The door is not deformed or warped.

(E) There is no other visible damage with the oven.

Servicing and repair work must be carried out only by trained service personnel.

DANGER

Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing.

Service personnel - Do not contact the following parts while the appliance is energized;

High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage

Harness;

If provided, Vent Hood, Fan assembly, Cooling Fan Motor.

All the parts marked “*” on parts list are used at voltages more than 250V.

Removal of the outer wrap gives access to voltage above 250V.

All the parts marked “∆” on parts list may cause undue microwave exposure, by themselves, or when they are damaged,

loosened or removed.

R-370EZ

ITEM DESCRIPTION

Power Requirements 120 Volts / 13.5 Amperes

60 Hertz

Single phase, 3 wire grounded

Power Output 1000 watts (IEC TEST PROCEDURE)

Operating frequency of 2450MHz

Case Dimensions Width 17-1/4"

Height 13-3/8"

Depth 18-3/8"

Cooking Cavity Dimensions Width 13-3/4"

Height 7-1/4"

1.4 Cubic Feet Depth 16-1/2"

Control Complement Touch Control System

Clock ( 1:00 - 12:59 )

Timer (0 - 99 min. 99 seconds)

Microwave Power for Variable Cooking

Repetition Rate;

HIGH................................................Full power throughout the cooking time

P-90 .................................................................... approx. 90% of Full Power

P-80 .................................................................... approx. 80% of Full Power

P-70 .................................................................... approx. 70% of Full Power

P-60 .................................................................... approx. 60% of Full Power

P-50 .................................................................... approx. 50% of Full Power

P-40 .................................................................... approx. 40% of Full Power

P-30 .................................................................... approx. 30% of Full Power

P-20 .................................................................... approx. 20% of Full Power

P-10 .................................................................... approx. 10% of Full Power

P-0 .................................................... No power throughout the cooking time

SENSOR COOKING pads , INSTANT ACTION pads

COMPU DEFROST pads, Number selection pads

CUSTOM HELP PAD, POWER LEVEL pad,

KITCHEN TIMER/CLOCK pad

STOP/CLEAR pad, MINUTE PLUS /START pad

Oven Cavity Light Yes

Safety Standard UL Listed FCC Authorized

DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J

SPECIFICATION

Figure O-1. Oven Schematic-Off Condition

SCHEMATIC

NOTE: CONDITION OF OVEN

1. DOOR CLOSED

2. CLOCK APPEARS ON DISPLAY

NOTE: " " indicates components with potential above 250V.

120V AC

60 Hz

OVEN

LAMP

AH SENSOR

OVEN LAMP

RELAY

TURNTABLE

MOTOR

FAN

MOTOR

POWER

TRANSFORMER

MONITOR

SWITCH

RECTIFIER

MAGNETRON

PRIMARY

INTERLOCK

SWITCH

TTM

FAN

MOTOR

MONITOR

FUSE 20A

N.O.

COM.

DOOR

SENSING

SWITCH

(RY1)

(RY2)

CONTROL UNIT

SECONDARY

INTERLOCK

RELAY

OVEN THERMAL

CUT-OUT

MG. THERMAL CUT-OUT

GRN

B2 B1

CAPACITOR

0.94µF

AC 2200V

R-370EZ

REF. NO. PART NO. DESCRIPTION Q'TY CODE

∆

ELECTRIC PARTS

1- 1 FACCDA085WREZ Power supply cord 1 AQ

1- 2 QFSHDA024WRZZ Fuse holder 1 AG

1- 3 QSW-MA137WRE0 Primary interlock switch / door sensing switch 2 AH

1- 4 FFS-BA023WRK0

Monitor fuse 20A and monitor switch (AM51620C53Y1) assembly

1AS

1- 5 RTHM-A116WRE0 Thermal cut-out 125 deg. C (MG) 1 AK

1- 6 FH-DZA100WRKZ High voltage rectifier assembly 1 AQ

1- 7 RC-QZA211WRE0 High voltage capacitor 1 AV

1- 7 RC-QZA286WRZZ High voltage capacitor (Interchangeable) 1 AV

1- 8 RMOTEA400WRZZ Fan motor 2 AX

1- 9 RTRN-A638WRZZ Power transformer 1 BP

1-10 RV-MZA288WRE0 Magnetron 1 BK

1-10 RV-MZA308WRZZ Magnetron (Interchangeable) 1 BL

1-11 RLMPTA082WRZZ Oven lamp 1 AL

1-12 RMOTDA186WRE0 Turntable motor 1 AQ

1-12 RMOTDA211WRE0 Turntable motor (Interchangeable) 1 AS

1-13 RTHM-A123WRZZ Thermal cut-out 125 deg. C (OVEN) 1 AK

1-14 FDTCTA212WRKZ AH sensor 1 AX

CABINET PARTS

2- 1 GDAI-A335WRWZ Base plate 1 AW

2- 2 GLEGPA087WRFZ Front leg 1 AK

2- 3 GLEGPA081WRFZ Leg 1 AC

2- 4 GCABUA807WRPZ Outer case cabinet 1 BD

2- 5 GCOVAA291WRFZ Harness cover 1 AH

POWER UNIT PARTS

3- 1 DPWBFC179WRUZ Power unit 1 BC

3- 1A QCNCMA431DRE0 2-pin connector (CN-B) 1 AC

3- 1B QCNCMA470DRZZ 9-pin connector (CN-C) 1 AF

3- 1C QCNCMA237DRE0 3-pin connector (CN-F) 1 AD

C1 RC-KZA087DRE0 Capacitor 0.1 uF 50V 1 AA

C2 VCEAB31VW108M Capacitor 1000 uF 35V 1 AF

C3 VCEAB31VW106M Capacitor 10 uF 35V 1 AA

C21 VCEAB31VW106M Capacitor 10 uF 35V 1 AA

C50-51 RC-KZA087DRE0 Capacitor 0.1 uF 50V 2 AA

D1-4 RH-DZA006PRE0 Diode (1N4002) 4 AD

D20-22 VHD1SS270A/-1 Diode (1SS270A) 3 AA

D40 VHD1SS270A/-1 Diode (1SS270A) 1 AA

IC2 VHIBA4558//-6 IC (BA4558) 1 AK

Q1 VS2SB1238//-3 Transistor (2SB1238) 1 AA

Q21 VSDTD143ES/-3 Transistor (DTD143ES) 1 AC

Q22 VSDTA143ES/1B Transistor (DTA143ES) 1 AA

R1 VRD-B12EF242J Resistor 2.4k ohm 1/4W 1 AA

R2 VRS-B13AA331J Resistor 330 ohm 1W 1 AA

R4 VRD-B12EF332J Resistor 3.3k ohm 1/4W 1 AA

R50 VRS-B13AA331J Resistor 330 ohm 1W 1 AA

R51 RR-DZA285DRZZ Resistor 3.32k ohm ±0.5% 1/4W 1 AC

R52 RR-DZA286DRZZ Resistor 3.57k ohm ±0.5% 1/4W 1 AC

R53 VRN-B12EK182F Resistor 1.8k ohm ±1.0% 1/4W 1 AA

R54 VRN-B12EK364F Resistor 360k ohm ±1.0% 1/4W 1 AA

RY1 RRLY-A076DRE0 Relay (OMIF-S-124LM) 1 AK

RY2 RRLY-A113DRE0 Relay (DU24D1-1P(M)-R) 1 AM

SP1 RALM-A014DRE0 Buzzer (PKM22EPT) 1 AG

T1 RTRNPA111DRE0 Transformer 1 AP

VRS1 RH-VZA032DRE0 Varistor (10G471K) 1 AE

ZD1 VHEHZ161///-1 Zener diode (HZ16-1) 1 AA

OVEN PARTS

4- 1 PHOK-A118WRFZ Latch hook 1 AH

4- 2 LBNDKA099WRW0 Capacitor holder 1 AD

4- 3 PDUC-A772WRWZ Fan duct 1 AN

4- 4 NFANJA047WREZ Fan blade 2 AL

4- 5 PPACGA084WRF0 TTM packing 1 AE

4- 6 ************* Oven cavity (Not a replaceable part) 1--

4- 7 GCOVHA423WRFZ Choke cover 1 AL

4- 8 LANGQA531WRWZ Lamp angle 1 AP

4- 9 PCOVPA361WREZ Waveguide cover 1 AD

4-10 LANG-A084WRFZ Separate angle A 1 AG

PARTS LIST

Note: The parts marked “∆” may cause undue microwave exposure.

The parts marked “*” are used in voltage more than 250V.

R-370EZ

REF. NO. PART NO. DESCRIPTION Q'TY CODE

∆

4-11 LANG-A085WRFZ Separate angle B 1 AG

4-12 LANG-A086WRFZ Separate angle C 1 AG

4-13 PCLI-A002WREZ PC support clip 2 AD

4-14 FANG-A013WRYZ Magnetron duct assembly 1 AP

4-15 LANGFA200WRPZ Support angle 1 AD

4-16 NCPL-A053WRFZ Coupling 1 AE

4-17 PCUSUA571WRPZ Cushion 1 AH

4-18 PDUC-A775WRTZ Exhaust duct 1 AP

4-19 PPACGA181WREZ Cushion 1 AH

4-20 PPACGA182WREZ Cushion 1 AC

4-21 PCUSUA573WRPZ Cushion 1 AC

4-22 PCUSUA313WRP0 Cushion 1 AF

4-23 PCUSUA578WRPZ Cushion 1 AG

4-24 PCUSUA577WRPZ Cushion 1 AC

4-25 PCUSGA561WREZ Cushion 1 AC

4-26 PCUSUA583WRPZ Cushion 1 AG

4-27 PCUSUA375WRP0 Cushion 1 AH

4-28 PCUSGA560WREZ Cushion 2 AB

4-29 PCUSGA564WREZ Cushion 1 AH

4-30 PCUSGA563WREZ Cushion 1 AH

DOOR PARTS

5- 1 FDORFA347WRTZ Door panel 1 AX

5- 2 PSHEPA775WREZ Sealer film 1 AH

5- 3 FWAKPA352WRKZ Door frame assembly 1 BE

5-3-1 FUNTKB060WREZ Key unit 1 AV

5-3-2 HPNL-A762WRRZ Door screen 1 AU

5- 4 LSTPPA193WRFZ Latch head 1 AE

5- 5 MSPRTA202WREZ Latch spring 1 AD

5- 6 DPWBFC176WRKZ CPU unit 1 BD

5- 7 LHLD-A236WRFZ LCD holder 1 AC

5- 8 PSHEPA786WREZ LED sheet 1 BB

5- 9 FW-VZA272DREZ 9-pin wire harness 1 AL

5-10 PCOVPA372WRWZ PWB cover 1 AF

5-11 PCUSUA567WRPZ Cushion 1 AE

5-12 XEBSD38P08000 Screw : 3.8mm x 8mm 4 AA

5-13 XEPSD30P08XS0 Screw : 3mm x 8mm 3 AA

5-14 LHLD-A237WRFZ Light guide 1 AL

5-15 PCUSUA461WRP0 Cushion 1 AB

MISCELLANEOUS

6- 1 FROLPA079WRK0 Turntable support 1 AP

6- 2 NTNT-A079WRF0 Turntable tray 1 AR

6- 2 NTNT-A084WRE0 Turntable tray (Interchangeable) 1 AQ

6- 3 FW-VZB827WREZ Main wire harness 1 AW

6- 4 QW-QZA242WRZZ High voltage wire B 1 AF

6- 5 TCAUAA265WRRZ DHHS caution label 1 AC

6- 6 TCAUAA254WRR0 Monitor caution label 1 AC

6- 7 TINSEA914WRRZ Instruction book 1 AM

6- 8 FW-VZB828WREZ Switch harness 1 AK

6- 9 FW-VZB802WREZ T.T. motor harness 1 AF

SCREWS,NUTS AND WASHERS

7- 1 XHPSD40P08K00 Screw : 4mm x 8mm 8 AA

7- 2 XHPSD40P08000 Screw : 4mm x 8mm 1 AA

7- 3 XOTSD40P08000 Screw : 4mm x 8mm 9 AA

7- 4 LX-CZA073WRE0 Special screw 1 AC

7- 5 XOTSD40P12000 Screw : 4mm x 12mm 2 AA

7- 6 XHPSD30P08XS0 Screw : 3mm x 8mm 2 AB

7- 7 XHTSD40P08RV0 Screw : 4mm x 8mm 9 AA

7- 8 LX-CZA070WRE0 Special screw (Torx tamper proof screw) 2 AC

7- 9 LX-CZ0052WRE0 Special screw 2 AA

7-10 XHPSD30P06000 Screw : 3mm x 6mm 1 AA

7-11 XHTSD40P08000 Screw : 4mm x 8mm 4 AA

7-12 XHTSD40P12RV0 Screw : 4mm x 12mm 1 AA

7-13 XOTSD40P12RV0 Screw : 4mm x 12mm 4 AA

7-14 XOTSF40P08000 Screw : 4mm x 8mm 2 AA

7-15 LX-EZA060WREZ Special screw 4 AA

7-16 XOTSD40P12000 Screw : 4mm x 12mm 1 AA

7-17 XHBWW30P08000 Screw : 3mm x 8mm 2 AB

R-370EZ

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

1. MODEL NUMBER

2. REF. NO.

3. PART NO.

4. DESCRIPTION

Order Parts from the authorized SHARP parts Distributor for your area.

Defective parts requiring return should be returned as indicated in the Service Policy.

POWER SUPPLY

CORD 120V 60Hz

COM.

N.O.

FAN

MOTOR

POWER

TRANSFORMER

NOTE:

The neutral (WHT) wire must be

connected to the terminal with "N"

mark on the power supply cord.

GRY

BLK

ORG

from Aug. 2001 Prod.

GRY

RED

BLK

RED

BLK

MONITOR

FUSE

HOLDER

GRY

WHT

RED

WHT

RY2

RY1

SECONDARY

INTERLOCK

RELAY

POWER UNIT

NOTE:

The grounding conductor of

the power supply cord has

been grounded by power

supply cord fixing screw.

The screw must always be

kept tight.

RED

ORG

from Aug. 2001 Prod.

SERVICE INFORMATION

The color of lead wire has been changed as follow.

MODEL EFFECTIVE FROM

R-370EK Serial No. from 26937

R-370ES Serial No. from 04928

R-370EZ 1 st. lot production

R-370EZ

7-4

1-14

7-17

7-7

7-3

7-7

4-2

1-7

2-3

7-16

1-6

4-10

7-6

7-3

1-10

7-7

1-12

7-1

4-16

7-5

4-20

4-12

4-13

1-4

4-22

7-1

7-9

7-11

7-13

7-15

7-10

1-9

4-44-11

7-3

7-2

1-8

4-1

1-1

4-25

4-6

4-24

4-28

4-17

4-18

6-6

7-14

7-12

7-3

7-8

4-19

4-21

4-29

7-7

1-5

1-4

1-3

4-5

4-30

1-2

1-3

3-1

4-14

4-8

1-11

4-15

7-5

2-5

4-4

7-1

2-1

7-3

2-2

4-9

6-1

6-2

7-13

4-3

7-1

4-23

1-13

4-26

6-5

4-27

2-4

7-11

OVEN AND CABINET PARTS

R-370EZ

Actual wire harness may be different from illustration.

(CAPACITOR)

5-13

5-11

5-12

5-10

5-9

5-6

5-13

4-7

5-7

5-1

5-14

5-6

6-3

6-4

5-2

5-8

5-4

5-15

5-12

5-3-2

5-3-1

5-3

6-8

6-9

5-5

MISCELLANEOUS

DOOR PARTS

R-370EZ

2001 SHARP CORP. (8S1.700E) Printed in U.S.A

No part of this publication may be reproduced,

stored in retrieval systems, or transmitted in any

form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without prior

written permission of the publisher.

PACKING AND ACCESSORIES

DOOR PROTECTION SHEET

SPADPA204WRE0

TOP PAD ASSEMBLY

FPADBA451WRKZ

WRAP COVER

SSAKHA072WREZ

Not replaceable items.

PACKING CASE

FPAK-A412WRKZ

BOTTOM PAD ASSEMBLY

FPADBA453WRKZ

6- 2 TURNTABLE TRAY

6-7 INSTRUCTION BOOK

& PRINTING MATTER

6- 1 TURNTABLE SUPPORT

TRAY PAD

SPADFA499WREZ

INTO THE

OVEN CAVITY

CABINET COVER

SPAKHA018WREZ

FOAM SHEET

SPAKHA017WREZ

Sharp 36-250 User manual

Brand: Sharp

Model: 36-250

Category: Microwaves

Type: User manual

This manual is also suitable for

Download PDF

report

Sharp 36-250 User manual

This manual is also suitable for

Sharp 36-250 User manual

Related papers

Other documents