Yamaha PEQ-200 Owner's manual

Printed in Malaysia WS30760

RX-V2065

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

G

00_RX-V2065_G_cv.fm Page 1 Thursday, July 23, 2009 10:40 AM

Black process 45.0° 240.0 LPI

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press LMAIN ZONE ON/OFF to

set this unit to the standby mode, and disconnect the AC

power plug from the wall outlet in the main room.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

.....AC 110/120/220/230-240 V, 50/60 Hz (General model)

.........................AC 220/230-240 V, 50/60 Hz (Asia model)

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by LMAIN ZONE ON/OFF.

In this state, this unit is designed to consume a very

small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Caution-ii En

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in

the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical

and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/

EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

Caution-iii En

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert the battery according to the polarity markings (+ and -).

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows

– the transmit indicator does not flash or is dim

• If the batteries run out, immediately remove them from the

remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries

immediately, taking care not to touch the leaked material. If

the leaked material comes into contact with your skin or gets

into your eyes or mouth, rinse it away immediately and

consult a doctor. Clean the battery compartment thoroughly

before installing new batteries.

• Do not use old batteries together with new ones. This may

shorten the life of the new batteries or cause old batteries to

leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may

be different even though they look the same.

• Before inserting new batteries, wipe the compartment clean.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote

control, the contents of the memory may be cleared. In such a

case, install new batteries and set the remote control code.

• Dispose of batteries according to your regional regulations.

1 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features....................................................................2

About this manual...................................................3

Supplied accessories................................................3

Part names and functions.......................................4

Front panel ................................................................. 4

Rear panel ..................................................................5

Front panel display..................................................... 6

Remote control........................................................... 6

Simplified remote control .......................................... 8

Quick start guide.....................................................9

L

Connections ...........................................................10

Placing speakers....................................................... 10

Connecting speakers ................................................ 11

Information on jacks and cable plugs ...................... 13

Connecting a TV monitor or projector .................... 14

Connecting other components ................................. 16

Connecting a Yamaha iPod universal dock or

Bluetooth™ wireless audio receiver.................... 18

Connecting to the network....................................... 19

Connecting a USB storage device ...........................19

Using the VIDEO AUX jacks.................................. 19

Connecting the FM and AM antennas ..................... 20

Connecting the power cable..................................... 20

Turning this unit on and off ..................................... 20

Optimizing the speaker setting for your

listening room (YPAO).....................................21

Using Auto Setup..................................................... 21

When an error message is displayed during

measurement........................................................ 23

When a warning message is displayed after

measurement........................................................ 23

Playback.................................................................24

Basic procedure........................................................ 24

Using the SCENE function ......................................24

Selecting a source on the GUI screen ...................... 25

Muting audio output.................................................25

Adjusting high/low frequency sounds

(tone control) ....................................................... 25

Enjoying pure hi-fi sound ........................................ 25

Using your headphones............................................ 26

Changing information on the front panel display.... 26

Enjoying the sound field programs .....................27

Selecting sound field programs................................27

Enjoying unprocessed input sources

(Straight decode mode)........................................ 30

Enjoying sound field programs without surround

speakers (Virtual CINEMA DSP) ....................... 30

Enjoy sound field programs with headphones

(SILENT CINEMA™) ........................................30

Using CINEMA DSP 3D mode ............................... 30

FM/AM tuning ......................................................31

Tuning in to the desired FM/AM station

(Frequency tuning) .............................................. 31

Registering FM/AM stations and tuning in

(Preset tuning)...................................................... 31

Radio Data System tuning....................................33

Displaying the Radio Data System information ...... 33

Selecting the Radio Data System program type

(PTY Seek) .......................................................... 33

Using the enhanced other networks (EON) data

service.................................................................. 34

Using iPod™..........................................................35

Controlling iPod™................................................... 35

Using Bluetooth™ components ........................... 37

Pairing the Bluetooth™ wireless audio receiver

and your Bluetooth component............................ 37

Playback of the Bluetooth™ component ................. 37

Using USB storage devices................................... 38

Playback of the USB storage device........................ 38

Using PC servers................................................... 39

Windows Media Player 11 setup .............................39

Playback of PC music contents................................ 39

Using the Internet Radio feature......................... 41

Listening to Internet Radio ...................................... 41

Other functions ..................................................... 42

Selecting the HDMI OUT jack ................................ 42

Using the HDMI™ control function........................ 42

Using the sleep timer ............................................... 42

Setting the option menu for each input source

(Option menu)................................................... 43

Option menu items................................................... 43

Selecting a video signal to be output during an audio

reproduction......................................................... 45

Operating various settings for this unit

(Setup menu) ..................................................... 46

Basic operation of the Setup menu .......................... 48

Using multi-zone configuration........................... 58

Connecting Zone2/3................................................. 58

Controlling Zone2/3................................................. 60

Controlling other components with the remote

control................................................................ 61

Setting remote control codes.................................... 61

Resetting all remote control codes........................... 61

Programming from other remote controls ............... 62

Advanced setup..................................................... 63

Troubleshooting.................................................... 65

Glossary................................................................. 76

Sound field program information ....................... 79

Information on HDMI™...................................... 80

Specifications......................................................... 81

Index ...................................................................... 82

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

APPENDIX

Information about software...................................i

List of remote control codes.................................iii

2 En

INTRODUCTION

■ Built-in 7-channel power amplifier

• Minimum RMS Output Power (20 Hz to 20 kHz, 0.08%

THD, 8 Ω)

• FRONT L/R: 130 W + 130 W

• CENTER: 130 W

• SURROUND L/R: 130 W + 130 W

• SURROUND BACK L/R: 130 W + 130 W

■ Speaker/Preout outputs

• Speaker terminals (7-channel), extra speaker terminals

(2-channel for presence or Zone2, 2-channel for

Zone3), preout jacks (7.1-channel)

■ Input/Output terminals

Input terminals

• HDMI input x 5 (rear x 4, front V-AUX x 1)

• Audio/Visual input

[Audio] Digital input (coaxial) x 2, digital input

(optical) x 2, analog input x 3 (rear x 2, front V-AUX

x 1)

[Video] Component video x 2, S-video x 1, Video x 5

(rear x 4, front V-AUX x 1)

• Audio input (analog) x 2

• Phono input (analog) x 1

• Multi-channel audio input (7.1-channel)

• DOCK terminal to connect a Yamaha iPod universal

dock (such as YDS-11, sold separately) or Bluetooth

wireless audio receiver (such as YBA-10, sold

separately)

• USB port to connect a USB storage device

• NETWORK port to connect a PC or access the Internet

Radio via LAN

Output terminals

• Monitor output

[Audio/Video] HDMI x 2

[Video] Component video x 1, Video x 1

• Audio/Visual output

[Audio] Analog x 1

[Video] Video x 1

• Audio output

Digital (optical) x 1, Analog x 1

• Zone2/3 output

Analog x 2

Other terminals

Remote input x 1, Remote output x 1

Trigger output x 2

■ Proprietary Yamaha technology for the

creation of sound fields

• CINEMA DSP 3D

• Compressed Music Enhancer mode

• Virtual CINEMA DSP

• SILENT CINEMA

■ Digital audio decoders

• Dolby TrueHD, Dolby Digital Plus decoder

• DTS-HD Master Audio, DTS-HD High Resolution

Audio, DTS Express

• Dolby Digital/Dolby Digital EX decoder

• DTS, DTS 96/24 decoder, DTS-ES Matrix 6.1, DTS-ES

Discrete 6.1

• Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic

IIx decoder

• DSD decoder

• DTS NEO:6 decoder

■ Sophisticated FM/AM tuner

• 40-station random and direct preset tuning

• Automatic preset tuning

• Radio Data System tuning

■

HDMI™ (High-Definition Multimedia Interface)

• HDMI interface for standard, enhanced or high-

definition video as well as multi-channel digital audio.

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

– High definition digital audio format signals capability

• Analog to analog and HDMI digital video up-

conversion (video ↔ component video → HDMI)

capability for monitor out

•

Analog video input up-scaling for HDMI digital video

output 480i(576i) or 480p(576p)

→

720p, 1080i or 1080p

• HDMI control function supported

• Dual HDMI output (possible to select individual or

simultaneous output)

■ Automatic speaker setup features

• “YPAO” (Yamaha Parametric Room Acoustic

Optimizer) for automatically optimizing speaker

outputs suitable for listening environments.

■ Other features

• 192-kHz/24-bit D/A converter

• GUI (graphic user interface) menus to optimize this unit

to suit individual audiovisual system

• iPod, USB and PC file browsing

• Album art display capability

• Pure Direct mode for pure hi-fi sound for all sources

• Adaptive dynamic range controlling capability

• SCENE function for changing input sources and sound

field programs with one key

• Bi-amplification connection capability

• Multi-zone function (Zone2/3)

• DHCP automatic or manual network configuration

Features

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &

other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and DTS-

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other

countries.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

This receiver supports network connections.

Bluetooth

™

Bluetooth is a registered trademark of Bluetooth SIG and is used by

Yamaha in accordance with a license agreement.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

Windows XP, Windows Vista, Windows Media Audio, Windows

Media Connect and Windows Media Player are either registered

trademarks or trademarks of Microsoft corporation in the United

States and/or other countries.

Check that you received all of the following parts.

• Remote control (page 6)

• Simplified remote control (page 8)

• Batteries (2) (AAA, R03, UM-4) (page 6)

• Power cable (page 20)

• Optimizer microphone (page 21)

• AM loop antenna (page 20)

• Indoor FM antenna (page 20)

• VIDEO AUX input cover (page 19)

About this manual

• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between

the front panel and the remote control, the key name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of

differences between the manual and product, the product has priority.

• For better viewing, we increase the size of characters used in example screen images in this manual. Therefore the size ratio of characters to other

objects (such as icons) may be different from that of the actual display image.

• “LMAIN ZONE ON/OFF” or “dHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the

attached sheet or “Part names and functions” (page 4) for the information about each position of the parts.

• ☞ indicates the page describing the related information.

• y indicates a tip for your operation.

Supplied accessories

4 En

A ZONE2 ON/OFF

Switches Zone2 on and off (page 60).

B HDMI THROUGH

Lights up in the following cases while this unit is on standby.

• when the HDMI control function is on

• when the HDMI signal standby-through function is currently

working

C ZONE3 ON/OFF

Switches Zone3 on and off (page 60).

D ZONE CONTROLS

Selects a zone to control with the main amplifier operations

(page 60).

E INFO

Changes information (input, DSP program, audio decoder, etc)

displayed on the front panel display (page 26).

F PRESET l / h

Selects an FM/AM preset station (page 32).

G MEMORY

Registers FM/AM stations as preset stations (page 32).

H BAND

Change the tuner bands between FM and AM.

I TUNING l / h

Changes FM/AM frequencies.

J Front panel display

Displays information on this unit (page 6).

K VOLUME control

Controls the volume of this unit (page 24).

L MAIN ZONE ON/OFF

Turns this unit on and off (page 20).

M PHONES jack

For plugging headphones (page 26).

N USB port

For connecting a USB memory device or USB portable audio

player (page 19)

O TONE CONTROL

Adjusts high-frequency/low-frequency output of speakers

(page 25).

P PROGRAM selector

Changes sound field programs (page 27).

Q STRAIGHT

Toggles between the selected sound field program and straight

decode mode (page 30).

R SCENE

Switches between linked sets of input sources and sound field

programs (page 24).

S PURE DIRECT

Changes mode to Pure Direct mode (page 25). This key lights up

when Pure Direct mode is on.

T INPUT selector

Selects an input source (page 24).

U OPTIMIZER MIC jack

For connecting the supplied optimizer microphone and adjusting

output characteristics of speakers (page 21).

V VIDEO AUX jacks

For connecting a game console, camcorder or digital camera to

either the HDMI IN jack or analog AUDIO/VIDEO jacks

(page 19).

Part names and functions

Front panel

ON/OFF

PHONES

MAIN ZONE

SILENT CINEMA

TONE CONTROL

PROGRAM

STRAIGHT PURE DIRECT

INPUT

OPTIMIZER MIC

VIDEO

HDMI IN

AUDIO

THROUGH

VIDEO

AUX

VOLUME

HDMI

EFFECT

BD/DVD

TV

CD

RADIO

SCENE

INFO

PRESET

l

h

l

h

MEMORY

ZONE2

ON/OFF

ZONE

CONTROLS

ZONE3

ON/OFF

BAND

TUNING

USB

LPSOQ T

ABC D E G HFIJK

UMN R V

5 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a DOCK terminal

For connecting an optional Yamaha iPod universal dock (YDS-

11) or Bluetooth wireless audio receiver (YBA-10) (page 18).

b PHONO jacks

For connecting a turntable (page 16).

c RS-232C terminal

Control expansion terminal for factory use only. Consult your

dealer for details.

d TRIGGER OUT 1/2 jacks

For connecting an external terminal with a trigger input terminal

to operate it linked with operation of this unit. Consult your

dealer for details.

e HDMI OUT 1/2 jacks

For connecting HDMI-compatible video monitors (page 14).

HDMI 1-4 jacks

For connecting external components for HDMI inputs 1-4

(page 16).

ANTENNA terminals

For connecting supplied FM and AM antennas (page 20).

MONITOR OUT jacks

Outputs visual signals from this unit to a video monitor, such as

a TV (page 14).

REMOTE IN/OUT jacks

For connecting an external component that supports the remote

control function (page 18).

f NETWORK port

For connecting to the network (page 19).

g SPEAKERS terminals

For connecting front, center, surround and surround back

speakers (page 11). Connect the presence speakers (page 11) or

the speakers for Zone2/3 (page 59) to EXTRA SP terminals.

h DIGITAL AUDIO jack

Outputs audio signals from a selected digital audio input source

to an external component (page 16).

i AV 1-6 jacks

For connecting external components for audio/visual inputs 1-6

(page 16).

j AV OUT jacks

Outputs audio/visual signals from a selected analog input source

to an external component (page 16).

k AUDIO 1/2 jacks

For connecting external components for audio inputs 1-2

(page 16).

l MULTI CH INPUT jacks

For connecting a player that supports a multi-channel output

(page 18).

m AUDIO OUT jacks

Outputs audio signals from a selected analog input source to an

external component (page 16).

ZONE2/3 OUT jacks

Output sound of this unit to an external amplifier set in a

different zone (page 58).

n PRE OUT jacks

Outputs multi-channel signals from up to 7.1 channels to an

external amplifier (page 18).

o AC IN

For connecting the supplied power cable (page 20).

Rear panel

DOCK

RS

-

232C

TRIGGER OUT

NETWORK

COMPONENT

VIDEO

P

R

P

B

12

Y

OPTICAL

OUT

(

TV

)

A

V

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDI O

OUT

ZONE3

OUT

ZONE2

OUT

FRONT

SURROUND

SUR. BACK SUBWOOFER

PRE OUT

CENTER

SINGLE

VIDEO

HDMI OUT 2HDMI OUT 1

ANTENNA

PHONO

UNBAL.

FM

GND

S VIDEO

AM

HDMI 1

(

BD/DVD

)

(

HDMI CONTROL

)

HDMI 2

HDMI 3

HDMI 4

VIDEO

IN

OUT

MONITOR OUT

SPEAKERS

12V

0.1A MAX.

FRONT

CENTER

SINGLE

SURROUND

SURROUND BACK/

BI-AMP

ZONE2/PRESENCEZONE3

12

CENTER

P

R

P

B

Y

REMOTE

COMPONENT

VIDEO

DIGITAL

AUDIO

EXTRA SP

SP2 SP1

GND

AC IN

cab

ijhklmno

dfeg

6 En

Part names and functions

a HDMI indicator

Lights up during normal communication when HDMI is

selected as an input source.

OUT 1/OUT 2 indicators

The respective indicator lights up when HDMI signals are

output from the HDMI OUT 1/2 jacks.

b CINEMA DSP indicator

Lights up when a sound field program that uses CINEMA DSP

is selected.

c CINEMA DSP 3D indicator

Lights up when CINEMA DSP 3D is activated.

d Tuner indicator

Lights up during receiving radio broadcast signals from an FM/

AM station (page 31).

e ZONE2/ZONE3 indicator

Lights up when Zone2 or Zone3 is turned on.

f SLEEP indicator

Lights up when the sleep timer is activated (page 42).

g MUTE indicator

Flashes when audio is muted.

VOLUME indicator

Displays volume levels.

h Cursor indicators

Light up if corresponding cursors on the remote control are

available for operations.

i Multi information display

Displays menu items and settings for the current operation.

j Speaker indicators

Indicate speaker terminals from which signals are currently

output.

Note

• Before installing batteries or using the remote control, make sure that you read “Notes on remote controls and batteries” in the “Caution” section.

■ Installing batteries

a Take off the battery compartment cover.

b Insert the two supplied batteries (AAA, R03, UM-4)

according to the polarity markings (+ and -) on the

inside of the battery compartment.

c Snap the battery compartment cover back into the

place.

■ Operation range

The remote control transmits a directional infrared ray. Be

sure to aim the remote control directly at the remote

control sensor on this unit during operation.

Front panel display

STEREO

SLEEP

VOL.

TUNED

PL PR

SW

C

LR

SL SR

SBL SB SBR

MUTE

3

ZONE

2

ZONE

3

OUT 1 OUT 2

acbfedg

hi jh

SW

C

LR

SL SR

SBL SB SBR

PL PR

Subwoofer

Front L

Surround L

Surround back L

Center

Front R

Surround R

Surround back R

Surround back

Presence L Presence R

Remote control

a

c

b

30 30

Remote control sensor window

within 6 m (20 ft)

7 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Remote control signal transmitter

Transmits infrared signals.

b Zone selection switch

Switches amplifiers (main, Zone2 or Zone3) to be operated by

the remote control (page 60).

c SOURCE POWER

Switches an external component on and off.

d Input selection keys

e Tuner keys

f INFO

Changes the information shown on the front panel display

(page 26).

g HDMI OUT

Switches the HDMI OUT jacks to output HDMI signals

(page 42).

h SCENE

Switches between linked sets of input sources and sound field

programs (page 24).

i ON SCREEN

Displays the GUI screen (page 25).

k External component operation keys

Operate recording, playback etc. of external components

(page 61).

l Numeric keys

Enter numbers.

m TV control keys

Enables operations of a TV or a projector (page 61).

n TRANSMIT

Lights up when a signal is output from the remote control.

o CODE SET

Sets remote control codes for external component operations

(page 61).

p POWER

Switches this unit on and standby (page 20).

q SLEEP

Switches the sleep timer operations (page 42).

r Sound selection keys

Selects sound field programs (page 27).

s OPTION

Displays the Option menu (page 43).

t VOLUME +/–

Adjust the volume of this unit (page 24).

u DISPLAY

Displays the play information on the video monitor.

When an iPod is connected: Changes the operation mode of the

iPod connected to the Yamaha iPod universal dock (page 35).

v MUTE

Turns the mute function on and off (page 25).

w Sub-input selection keys

Selects USB, NET RADIO or PC when “USB/NET” is selected

as the input source.

HDMI 1-4

Selects HDMI inputs 1 through 4.

AV 1-6

Selects AV inputs 1 through 6.

AUDIO 1/2

Selects AUDIO inputs 1 and 2.

V-AUX

Selects a signal input from the VIDEO AUX jacks.

PHONO

Selects a signal input from the PHONO jacks.

MULTI

Selects a signal input from the MULTI CH

INPUT jacks.

DOCK

Selects a Yamaha iPod universal dock/Bluetooth

wireless audio receiver connected to the DOCK terminal.

TUNER

Selects the FM/AM tuner.

USB/NET

Selects a USB device or a signal input via

network (selected by wSub-input

selection keys).

BD

DVD

TV

CD

RADIO

SLEEP

FM AM

INFO

MEMORY

1 2 3

4

1 2 3

4

5 6 1

2

PHONO

MULTI

DOCK

TUNER

V-AUX

HDMI

MUSIC

STEREO

ENHANCER SUR. DECODE

MOVIE

MUTE

STRAIGHT

HDMI OUT

PURE DIRECT

USB/NET

PRESET TUNING

ON SCREEN OPTION

SOURCE

POWER

7 85 6

9 0

1 2 3 4

USB NET RADIO PC

TOP

MENU

SCENE

RETURN

REC

ENT

POWER

TV

INPUT

MUTE

ENTER

VOLUME

DISPLAY

MENU

HDMI

AUDIO

TRANSMIT

CODE SET

10

TV VOL TV CH

MAIN

ZONE 2

ZONE 3

AV

POWER

p

q

s

r

t

u

v

w

o

n

a

c

d

e

g

h

i

k

l

m

b

j

f

FM/AM

Switches a band between FM and AM.

MEMORY

Presets radio stations.

PRESET k / n

Selects a preset station.

TUNING k / n

Changes FM/AM frequencies.

j Cursors k / n / l / h

Select menu items or change

settings.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen or

ends the menu display.

8 En

Part names and functions

Use the supplied simplified remote control to make basic controls of this unit. Keys on the simplified remote control

function as well as the identical keys on the main remote control (page 6).

Note

• Before using the simplified remote control or replacing the battery, make sure that you read “Notes on remote controls and batteries” in the “Caution”

section.

y

• To select an input source, press INPUT l / h repeatedly.

• The printings “TAG” and “PRG SELECT” are for U.S.A. model.

■ Setting the controlling zone

Follow the procedure below to select an amplifier (main,

Zone2 or Zone3) to be operated by the simplified remote

control (page 60).

■ Setting the remote control ID

Follow the procedure below to set the remote control ID of

the simplified remote control. For details about remote

control ID, see page 64.

■ Replacing the battery of the simplified

remote control

Change the battery when the operation range of the

simplified remote control decreases.

Simplified remote control

Zone to select Procedure

Main Press and hold h (right of ENTER) and

BD/DVD for more than 3 seconds.

Zone2 Press and hold h (right of ENTER) and TV

for more than 3 seconds.

Zone3 Press and hold h (right of ENTER) and CD

for more than 3 seconds.

Zone to select Procedure

ID1 Press and hold l (left of ENTER) and BD/

DVD for more than 3 seconds.

ID2 Press and hold l (left of ENTER) and TV

for more than 3 seconds.

MUTE

VOLUME

INPUT

SLEEP

SCENE

BD

DVD

TV CD

RADIO

POWER

ON SCREEN

OPTION

TAG

PRESET

PRG SELECT

ENTER

DISPLAYRETURN

Remove the insulation sheet

Use a straight

pin to remove

the cover.

Replace the

battery with a

new CR2025

battery.

Close the

cover.

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

When you use this product for the first time, perform setup following the steps below. See the related pages for details on

operations and settings.

Prepare speakers, DVD player, cables, and other items

necessary for setup.

For example, prepare the following items for setting up a

7.1-channel sound system.

y

• The priority of the requirement of other speakers is as follows:

1 Two surround speakers

2 One center speaker

3 One (or two) surround back speaker(s)

• Video and audio cables are unnecessary if you use HDMI cables.

Place your speakers in the room and connect them to this

unit.

y

• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)

that automatically optimizes this unit based on room acoustic

characteristics (audio characteristics of the speakers, speaker positions,

and room acoustics, etc.).

You can enjoy good balanced sound without special knowledge by using

the YPAO technology (☞P. 21).

Connect your TV, DVD player, or other components.

Connect the power cable and turn on this unit.

Select the component connected in step 3 as an input

source and start playback.

y

• This unit supports the SCENE function (page 24) that changes the input

source and sound field program at one time. Four scenes are preset for

different purposes for Blu-ray disc, DVD and CD, and you can select

from a scene from those just by pressing a remote control key.

Quick start guide

Step 1: Prepare items for setup

Requirements qty.

Speakers Front speaker 2

Center speaker 1

Surround speaker 2

Surround back

speaker

2

Active subwoofer 1

Speaker cable 7

Subwoofer cable 1

Reproduction component such as DVD player 1

Video monitor such as TV 1

Video cable or HDMI cable 2

Audio cable 2

Front right speaker

Subwoofer

Surround left speaker

Surround right speaker

Front left

speaker

Video monitor

Center

speaker

Components

(such as DVD player)

Surround Back

right speaker

Surround Back

left speaker

Step 2: Set up your speakers

• Placing speakers ☞P. 1 0

• Connecting speakers ☞P. 1 1

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 1 4

• Connecting other components ☞P. 1 6

• Connecting a multi-format player or an

external decoder ☞P. 1 8

• Connecting an external amplifier ☞P. 1 8

• Connecting a USB storage device ☞P. 1 9

• Connecting a Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞P. 1 8

• Connecting to the network ☞P. 1 9

• Connecting the FM and AM antennas ☞P. 2 0

Step 4: Turn on the power

• Connecting the power cable ☞P. 2 0

• Turning this unit on and off ☞P. 2 0

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 2 4

• Selecting sound field programs ☞P. 2 7

10 En

PREPARATION

This unit supports up to 7.1-channel surround. We recommend the following speaker layout in order to obtain the

optimum surround effect.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

■ Front left and right speakers (FL and FR)

The front speakers are used for the front channel sounds

(stereo sound) and effect sounds. Place these speakers at

an equal distance from the ideal listening position. Adjust

the height of the TV or screen so that about 1/4 of the

screen from the bottom is aligned with the tweeters of the

front speakers.

■ Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). Place it halfway between the left and

right speakers. When using a TV, place the speaker just

above or just under the center of the TV with the front

surfaces of the TV and the speaker aligned. When using a

screen, place it just under the center of the screen.

■ Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place them at the rear left and rear right facing the

listening position. To obtain a natural sound flow in the

5.1-channel speaker layout, place them slightly further

back than in the 7.1-channel speaker layout.

■ Surround back left and right speakers (SBL

and SBR) / Surround back speaker (SB)

The surround back left and right speakers are used for rear

effect sounds. Place them at the rear of the room facing the

listening position at least 30 cm (1 ft) away from each

other, ideally at the same distance as that between the

front left and right speakers.

In the 6.1-channel speaker layout, surround back left and

right channel sound signals are mixed down and output

from the single surround back speaker.

In the 5.1-channel speaker layout, surround back left and

right channel sound signals are output from the surround

left and right speakers.

■ Subwoofer (SW)

The subwoofer speaker is used for bass sounds and low-

frequency effect (LFE) sounds included in Dolby Digital

and DTS signals. Use a subwoofer with a built-in

amplifier, such as the Yamaha Active Servo Processing

Subwoofer System. Place it exterior to the front left and

right speakers facing slightly inward to reduce reflections

from a wall.

Connections

Placing speakers

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

SW

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

SW

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Speaker channels

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

■ Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the

front speakers with extra ambient effects produced by the

sound field programs (page 27). We recommend that you

use the presence speakers especially for the CINEMA

DSP sound field programs. To use the presence speakers,

connect the speakers to SP1 terminals and then set “Extra

Speaker Assignment” to “Presence” (page 49).

Connect your speakers to the respective terminals according to your speaker layout. The following illustration shows how

to connect speakers for 7.1-channel speaker layout.

y

• You can connect Zone2/3 speakers to the EXTRA SP (SP1/SP2) terminals (page 59).

• You can connect up to two subwoofers. When two subwoofers are connected, the same sound is output from them.

FR

PRPL

C

FL

0.5 to 1 m (1 to 3 ft)0.5 to 1 m (1 to 3 ft)

1.8 m

(6 ft)

1.8 m

(6 ft)

1/4 from

bottom

Connecting speakers

a

b

c

d

e

f

g

h

i

j

k

SUBWOOFER

SPEAKERS

FRONT

CENTER

SINGLE

CLASS 2 WIRING

CABLAGE

CLASSE 2

SURROUND

SURROUND BACK/

BI-AMP

ZONE2/PRESENCE

12

SP1

NETW

O

R

K

SU

R.

B

AC

K

SU

B

W

OO

FE

R

H

INPUT

AU

DI

O

OU

T

Z

O

NE3

OUT

Z

O

NE2

OUT

FR

O

N

T

S

URR

O

UN

D

S

UR

.

BA

C

K

PRE O

U

T

C

ENTER

S

INGL

E

3

HDMI

4

C

ENTER

E

c

g f

h i

e d

b a

k j

Speakers Jacks on this unit 7.1-channel 6.1-channel 5.1-channel

a Front left FRONT (L) ✔✔✔

b Front right FRONT (R) ✔✔✔

c Center CENTER ✔✔✔

d Surround left SURROUND (L) ✔✔✔

e Surround right SURROUND (R) ✔✔✔

f Surround back left

(Surround back for 6.1-channel)

SURROUND BACK (L)

(SINGLE)

✔✔

g Surround back right SURROUND BACK (R) ✔

h Subwoofer 1 SUBWOOFER 1 ✔✔✔

i Subwoofer 2 SUBWOOFER 2 Option Option Option

j Presence left SP1 (L) Option Option Option

k Presence right SP1 (R) Option Option Option

12 En

Connections

■ Connecting speaker cables

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist bare wires of the cable

together so that they will not cause a short

circuits.

2 Loosen the knob, insert the twisted bare

wires into the hole and then tighten the knob.

■ Using bi-amplification connections

If you do not connect surround back speakers, you can use

the SURROUND BACK/BI-AMP jacks to make bi-

amplification connections to one speaker system which

supports bi-amplification connection as shown below.

To activate the connections, set “BI-AMP” to “ON” in the

advanced setup menu (page 63).

Note

• You cannot use surround back speakers or extra speakers (presence and

Zone2 speakers) when bi-amplification connections are made.

Caution

• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently

or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit

and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this

unit and the other end to that of your speaker.

• Before connecting the speakers, be sure to disconnect the power cable.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or

speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned

on.

• If images on the monitor (CRT) are distorted, place the speakers away from the video monitor.

• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in the advanced setup menu before

connecting the speakers (page 63). You can also use 4-ohm speakers as the front speakers when you set “SP IMP.” to

“6ΩMIN”.

Connecting the banana plug (Except Korea,

U.K., Europe, Russia and Asia models)

Tighten the knob and then insert the banana plug into

the end of the terminal.

10 mm (0.4 in)

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Caution

Before making bi-amplification connections, remove

any brackets or cables that connect a woofer with a

tweeter. Refer to the instruction manuals of speakers for

details.

When not making bi-amplification connections, make

sure that the brackets or cables are connected before

connecting the speaker cables.

SURROUND BACK/

BI-AMP

FRONT

Front speakers

Right Left

This unit

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are

connecting.

■ Audio jacks

■ Video jacks

■ Video/audio jacks

y

• We recommend that you use a commercially available 19-pin HDMI

cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect this unit

to other DVI components.

• You can check the potential problem about the HDMI connection

(page 44).

Information on jacks and cable plugs

Jack and cables Description

Analog audio jacks To transmit conventional analog

stereo audio signals. Use stereo pin

cables.

COAXIAL jacks To transmit coaxial digital audio

signals. Use pin cables.

OPTICAL jacks To transmit optical digital audio

signals. Use optical fiber cables.

Jack and cables Description

VIDEO jacks To transmit conventional

composite video signals. Use pin

cables.

S VIDEO jack To transmit S-video signals that

include luminance (Y) and

Cameroonians (C) components.

Use an S-video cable.

COMPONENT VIDEO

jacks

To transmit component video

signals that include luminance (Y),

chrominance blue (PB) and

chrominance red (PR) components.

Use component video cables.

L

R

(white)

(red)

COAXIAL

C

(orange)

OPTICAL

O

VIDEO

V

(yellow)

S VIDEO

S

PR

PB

Y

COMPONENT

VIDEO

P

B

Y

P

R

(red)

(blue)

(green)

Jack and cables Description

HDMI jacks To transmit digital video and

digital audio signals. Use HDMI

cables.

HDMI

14 En

Connections

According to the types of video input jacks available on your video monitor (such as a TV or projector), choose one of

the connection methods as shown below. When you connect video players such as a DVD player to this unit with an

HDMI connection, connect your video monitor to this unit with an HDMI connection.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ If your video monitor has an HDMI input jack

y

• This unit is equipped with two HDMI OUT jacks. You can select the

active HDMI OUT jack(s) by pressing gHDMI OUT (page 42).

• This unit supports the HDMI control function (page 42). If your TV

supports the HDMI control function, connect the TV to the HDMI OUT

1 jack to control this unit with the remote control of your TV.

■ If your video monitor does not have HDMI

input jacks but component video input jacks

■ If your video monitor has neither HDMI nor

component video input jacks

Connecting a TV monitor or projector

Jacks on components Jacks on this unit

a HDMI input HDMI OUT 1

b HDMI input HDMI OUT 2

HDMI OUT 2HDMI OUT 1

(

HDMI CONTROL

)

TRI

GG

ER

OU

T

12

H

DMI

1

(

BD

/

DV

D

)

HDMI

2

HDMI

3

VIDEO

IN

O

U

T

MONI

T

O

R OU

T

12

V

0

.1A MAX.

P

REM

OT

E

CO

MP

O

NENT

G

ND

a

HDMI

b

TV

Projector

Jacks on components Jacks on this unit

c Component video output MONITOR OUT

(COMPONENT VIDEO)

Jacks on components Jacks on this unit

d Video input (composite) MONITOR OUT (VIDEO)

M

O

NI

T

O

R

OUT

P

R

P

B

Y

COMPONENT

VIDEO

TRI

GG

ER

OU

T

12

2

H

DMI

O

UT

HDMI

1

(

BD

/

DV

D

)

H

DMI

2

H

DMI

3

VIDE

O

IN

OUT

12V

0.1

A

MAX

.

REM

OT

E

c

P

B

YP

R

TV

VIDEO

MO

NIT

OR OUT

T

RI

GG

ER

OU

T

12

VIDE

O

2

H

DMI

OU

T

HDMI

1

(

B

D

/

DV

D

)

HDMI

2

HDMI

3

IN

O

UT

O

12V

0

.1A MAX

.

REM

O

T

E

CO

MP

O

NEN

T

V

d

TV

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

To output sound of a TV from this unit, make connection

between one of the AV 1-6 jacks of this unit and an audio

output jack of the TV.

If the TV supports an optical digital output, we

recommend that you use the AV 1 jack. Connecting to the

AV 1 jack allows you to switch an input source to the AV 1

jack with a just a single key operation using the SCENE

function (page 24).

Outputting TV sounds from this unit

OPTICAL

(

TV

)

A

V

A

1

P

R

P

B

Y

AV

2

CO

AXIAL

AV

3

(

C

D

)

CO

AXIAL

AV

6

AV

O

UT

AU

D

I

O1

AU

D

VIDE

O

P

R

P

B

O

Digital output

(optical)

TV

16 En

Connections

This unit has input and output terminals for respective input and output sources. You can reproduce sound and movies

from input sources selected with the front panel display or remote control.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ Audio and video player / Set-top box

Connecting other components

External

component

Signal

Output jacks on

components

Input jacks on this unit

External component

with HDMI output

Audio/Video HDMI output HDMI 1 (BD/DVD)

HDMI 2

HDMI 3

HDMI 4

External component

with component video

output

Audio Optical digital output AV 1 (TV) OPTICAL

Video Component video output COMPONENT VIDEO

Audio Coaxial digital output AV 2 COAXIAL

Video Component video output COMPONENT VIDEO

External component

with S-video output

Audio Analog audio output AV 5 Analog audio

Video S-video output S VIDEO

External component

with composite video

output

Audio Coaxial digital output AV 3 (CD) COAXIAL

Video Composite output VIDEO

Audio Optical digital output AV 4 OPTICAL

Video Composite output VIDEO

Audio Analog audio output AV 5 Analog audio

Video Composite output VIDEO

Audio Analog audio output AV 6 Analog audio

Video Composite output VIDEO

COMPONENT

VIDEO

P

R

P

B

Y

OPTICAL

OUT

(

TV

)

A

V

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

VIDEO

PHONO

S VIDEO

HDMI 1

(

BD/DVD

)

HDMI 2

HDMI 3

HDMI 4

CENTER

DIGITAL

AUDIO

GND

D

OC

K

RS

-

232

C

TRI

GG

ER

O

U

T

N

12

Z

O

N

OU

H

DMI

OU

T

2

HDMI

OU

T

1

ANTENNA

UNB

AL

.

FM

G

N

D

AM

(

HDMI

CO

NT

RO

L

)

V

IDE

O

IN

O

UT

MONITOR OU

T

12

V

0.1

A

MAX.

F

R

O

N

T

P

R

P

B

Y

R

EM

O

T

E

CO

MP

O

NEN

T

VIDE

O

Audio / video output (AV OUT)

Audio input (AUDIO 1/2)

HDMI input

(HDMI 1-4)

Audio output

(AUDIO OUT)

Multi channel audio input (MULTI CH INPUT)

Audio output

(DIGITAL AUDIO)

Audio / video input

(AV 1-6)

Audio input (PHONO)

Page is loading ...

Yamaha PEQ-200 Owner's manual

This manual is also suitable for

Yamaha PEQ-200 Owner's manual

Related papers

Other documents