GBC 7500S User manual

Page is loading ...

Your safety as well as the safety of others is important to GBC. In this instruction

manual and on the product are important safety messages. Read these

messages carefully.

The safety alert symbol precedes each safety message in this instruction

manual and on the product. This symbol indicates a potential personal

safety hazard that could hurt you or others, as well as cause product or

property damage. Do not connect this unit to electrical power or attempt

to operate it before you have read these operating instructions. Save these

instructions for later use.

Important Safety Instructions

The following warning is found inside of the cabinet door:

This safety message means that you could be

seriously hurt or killed if you open the product and

expose yourself to hazardous voltage.

The following warning is found on the bottom of the product:

This safety message means that you could be

seriously hurt if you place your hands in the discharge

area.

This means don’t reach into the feed opening of the cutting head. This

could hurt you.

This means you should be careful because long hair can become

entangled in the cutting head. This could hurt you.

This means be careful of ties and other loose clothing which could

become entangled in the cutting head. This could hurt you.

This means you should be careful of loose jewelry which could become

entangled in the cutting head. This could hurt you.

This means do not allow children to use the shredder.

2

English

ELECTRICAL SAFEGUARDS

Unplug your shredder before moving it, emptying the bag, or when it is

not in use for an extended period of time.

Do not operate with a damaged power supply cord or plug, after it

malfunctions, or after it has been damaged in any manner.

Do not overload electrical outlets beyond capacity as this can result in

ﬁre or electrical shock.

The socket-outlet should be installed near the equipment and shall be

easily accessible.

Do not alter attachment plug. Plug is conﬁgured for the appropriate

electrical supply.

Do not use near water.

Keep out of the reach of children.

Do not use extension cords to connect this product to the power supply.

SERVICE

Do not attempt to service or repair the unit yourself. If your shredder should

require service, contact your local dealer or call GBC National Service at

800-790-7787. Please have the model and serial number of your shredder

ready when calling.

•

3

Figure 1. The door must be closed

when operating the shredder.

Figure 3.

4

Figure 2. Keep the area around the

electrical outlet clear.

Unplug the shredder before cleaning

it.

Do not perform any repairs on the

shredder. (See page 12).

Figure 3. Do not shred CDs or DVDs

in the cross cut model (7550X). It may

splinter disks and kick them back out.

Only the straight cut model (7500S) is

suitable to destroy CDs or DVDs.

Do not attempt to shred paper clips

with the cross cut model.

120V / 120A min.

Figure 1.

Figure 2.

English

Figure 4. Do not operate the

shredder without the safey guard

in place.

Figure 5. The shredder turns off

after one hour of inactivity. Turn

the power switch off when not in

use for extended times.

5

Figure 4.

Figure 5.

Set Up

A

2.

1.

ASSEMBLY

Figure 6.

Plastic Bag

Pull out the waste receptacle

frame and remove the round

belt from around the frame.

Insert the included plastic bag

through the pull-out frame and

fold the top of the bag over the

frame.

Secure the bag with the round

belt.

Slide the waste receptacle in

and close the cabinet door.

Oiler

Hook the oiler holder over the

edge of the cabinet.

Remove the sticky tape from

the oil tube.

Remove the cap from the oil

bottle, insert the oil tube into

the bottle, and tighten the cap.

Place the oil bottle in the holder.

The oil bottle has a ﬁll level indication

(A).

Figure 7. Plug cord into the electrical

outlet.

Keep the area in front of the outlet

clear for easy access.

1.

a.

b.

c.

d.

2.

a.

b.

c.

d.

6

Figure 6.

Figure 7.

English

OILER

Figure 8. When using for the

ﬁrst time or when the oil bottle

is changed:

Press until the EMPTY LED

(A) no longer blinks red.

•

Figure 9. Flashing INJECT LED:

Indicates cutting shafts are

being automatically oiled.

Flashing EMPTY LED:

Indicates oil bottle is empty.

•

7

A

B

Operation

Figure 8.

Figure 9.

OPERATING THE SHREDDER

Figure 10.

Press the forward button to turn

the shredder on. The green light

shows that the shredder is ready to

operate.

Feed paper in to the middle of the

the throat. An auto sensing photo

cell detects the paper and starts

the machine. The shredder stops

automatically when no more paper

is inserted.

STANDBY MODE

After one hour of inactivity, the

shredder goes into standby and the

green LED turns off. Repeat step 1

above to turn the shredder back on.

1.

2.

SHEET CAPACITY INDICATOR

Figure 11.

The shredder has an ECC (electronic

capacity control) which indicates the

sheet capacity being used during

shredding (A).

Red LED (A).

The shredder stops automatically if

too much paper is inserted. The paper

is reversed.

Yellow LED (B).

Maximum sheet capacity during

shredding.

Green LED (C).

Normal capacity during shredding.

8

A

2.

1.

Figure 10.

Figure 11.

English

Figure 12. Shredder stops

automatically when door is opened

and a red LED indicator lights.

Figure 13. The shredder stops

automatically when the plastic bag

is full. Empty the bag when the “bag

full” yellow indicator lights.

(

See page 6).

9

Figure 12.

Figure 13.

Figure 14. The shredder stops

automatically when too much paper

is inserted at the same time. The

shredder features an automatic

reverse function that will be activated

when too much paper has been

inserted.

Figure 15. If necessary, when a paper

jam occurs and the automatic reverse

function does not clear all of the

paper, press the reverse button to

reverse the cutting unit and release

the paper.

Note: The auto sensing photo cell

must not be obstructed.

Once the shredder is clear, re-insert

smaller quantities of paper.

10

Figure 14.

Figure 15.

English

Figure 16. The shredder

automatically stops if the safety

guard (A) is opened (symbol

ﬂashes ). Close the safety guard

to shred paper. To remove any

paper debris from a paper jam,

the machine runs for a short time

in reverse with the safety guard

open. If required, press the reverse

button several times.

11

Figure 16.

Troubleshooting

12

A

B

Symptom Corrective Action

Machine will not start. Plug unit in.

Switch unit to Power On by pressing the forward

button (green LED lights).

Feed paper in to the center of the feed opening

where the auto sensing photo cell is located.

Close the cabinet door.

Empty the shred bag.

Close safety guard.

Bag full indicator lights

but bag is not full.

Figure 17.

Unplug unit from electrical outlet.

Remover paper debris between the cutting head

from below with a brush (not included). Figure 18.

Figure 17.

Figure 18.

English

13

Symptom Corrective Action

Machine will not stop. Unplug unit from electrical outlet.

Clean the auto sensing photo cell with a small

brush (not included). Figure 19.

Machine stops. Overload protection. Allow unit to cool down

approximately 5 to 10 minutes.

Symbol ﬂashes

When symbol stops ﬂashing, machine is

ready for operation.

•

If none of the troubleshooting actions correct the problem, contact your local

dealer or call GBC National Service at 1-800-790-7787.

Figure 19.

Accessories

Environmentally safe oil 33.8 oz. (1 litre)

Part number 1753190

Shredder bags for models 7500S and 7550X (100 bags)

Part number 1145482

To order, visit www.gbcconnect.com or call 1-800-723-4000.

14

Agency Listing

English

UL Listed 802 D

Sound level information: The sound level at the work place is less than

the ISO 7779 standard’s maximum permissible level of < 70 db (A).

The exact technical speciﬁcations can be found on the technical

speciﬁcations sticker on the machine.

Subject to alterations without notice.

Be sure to register your warranty online at www.gbcconnect.com.

Date purchased:

Serial number:

Notes:

15

Page is loading ...

ACCO Brands Corporation

300 Tower Parkway

Lincolnshire, IL 60069-3640

www.gbcconnect.com

800.723.4000

GBC 7500S User manual

This manual is also suitable for

GBC 7500S User manual

in other languages

Related papers

Other documents