Essick 427 300 Care & Use Manual

Brand: Essick

Model: 427 300

Category: Dehumidifiers

Type: Care & Use Manual

This manual is also suitable for

Essick 427 300 is an evaporative humidifier that adds invisible moisture to your home by moving dry inlet air through a saturated wick. As air moves through the wick, the water evaporates into the air, leaving behind any white dust, minerals, or dissolved and suspended solids. Thanks to that, there is no messy mist or spray, just clean and invisible moist air. It has two speed or variable fan speed allowing you to use the low setting for the quietest operation or a high setting for maximum output.

OWNER’S

CARE

USE

MANUAL

EVAPORATIVE

HUMIDIFIER

READ AND SAVE THESE INSTRUCTIONS

MODELS:

427 300 OAK BURL 2 SPD

696 400 LT OAK VARIABLE SPD

697 500 CHERRY VARIABLE SPD

• Automatic Humidistat

• Automatic Shutoff

• Quiet Setting for Nighttime use

• Easy to clean, removable power pack

SAVE THE ENVIRONMENT

RECYCLE APPROPRIATE MATERIALS

Patents: 5,037,583; 5,110,511; 5,133,904

Other Patents Pending

To order parts and accessories call

1-800-547-3888

696 400

697 500 427 300

French and Spanish

Instructions included.

Se incluyen instrucciones

En Español y Francés.

Directives en Français et en

espagnol compris

IMPORTANT SAFEGUARDS

READ BEFORE USING YOUR HUMIDIFIER

1. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric

shock, this plug is intended to fit into a polarized 120-volt AC, 15 amp outlet, and only one way. If the

plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

Do not attempt to defeat this safety feature. If an extension cord must be used, it should also accept

the wide blade plug and meet this electrical rating.

2. Do not place the cord under rugs, near loose draperies, in traffic areas, nor near heat sources or

combustible materials.

3. Do not use the humidifier if the cord is damaged.

4. Always unplug the power cord before filling, cleaning, servicing, or when the unit is not in use.

5. This humidifier is UL/CUL listed with Essick Air brand evaporative wicks in place.

6. It is very important that cleaning solutions such as bleach, anti-bacteria treatment or descaler, which

could be used to clean the cabinet, are not sprayed or applied to the chassis assembly. These

solutions can cause serious electrical malfunction of the humidifier.

INTRODUCTION

Your Essick Air evaporative humidifier adds invisible moisture to your home by moving dry inlet air through

a saturated wick. As air moves through the wick, the water evaporates into the air, leaving behind any

white dust, minerals, or dissolved and suspended solids. Because the water is evaporated, there is no

messy mist or spray, just clean and invisible moist air.

As the evaporative wick traps accumulated minerals from the water, its ability to absorb and evaporate

water decreases. We recommend changing the wick at the beginning of every season. In hard water

areas, more frequent replacement may be necessary to maintain your humidifier’s efficiency.

Use only Essick Air brand replacement wicks and chemicals. To order parts, wicks and chemicals call 1-

800-547-3888. The 400 and 600 Series humidifiers use Essick Air wick # 1041 and accommodate air filter

#1051. Only the Essick Air evaporative wick guarantees the certified output of your humidifier. Use of wicks

other than Essick Air brand will void your warranty as well as the certification of output and may reduce the

efficiency of your humidifier.

CAUTION: Do NOT position the unit directly in front of a hot air duct or radiator. Do NOT place on

soft carpet.

HOW YOUR HUMIDIFIER WORKS

Dry air is drawn into the

humidifier though the

back and moisturized

as it passes through the

evaporative wick. It is

then fanned out into the

room.

LEGEND:

1. Water bottle

2. Chassis/power pack

(motor/fan assembly)

3. Evaporative wick

4. Water reservoir

5. Dry room air intake

6. Moist air output

ASSEMBLY

UNPACKING AND SETTING UP THE UNIT

1. Remove the two inserts from the top of the humidifier.

2. Lift off the water bottle covers. Remove the water bottles, lift off the chassis/power pack and then

remove the humidifier cabinet from the carton.

3. Remove the evaporative wick and all of the remaining packaging materials from the cabinet. Check to

see that you have all of the following items removed from the boxes, accessory kit, and cabinet before

discarding the packaging:

♦ Filler Hose ♦ Evaporative Wick

♦ Caster kit ♦ Two end covers

♦ Bacterial treatment sample

♦ Two Water Bottles

♦ Optional Air Care ® filter (included on 697 and

427 models; sold separately on 696 model

CASTERS

4. Turn the emptied cabinet upside down. Insert each caster stem into a caster hole on each corner of the

humidifier bottom. The casters should fit snugly and be inserted until the stem shoulder reaches the

cabinet surface.

5. Turn the cabinet right side up.

EVAPORATIVE WICK

6. Insert the 1041 wick into the unit. The wick has a mounting

rib on the top edge which hooks over a rib at the inside back

of the cabinet. This allows the wick to hang in the water

channel (see cutaway illustration for details). Hang wick into

cabinet as shown.

OPTIONAL AIR CLEANING FILTER

(included on 427 and 697 models; sold separately on 696)

7. If available, install the 1051 AirCare® filter at the back of the

unit. The filter has tangs that engage into four keyhole

slots that mount the AirCare® filter onto the outside of the back of the cabinet.

FILLING INFORMATION

8. Your humidifier is equipped with two water bottles. On the 696 and 697 models each bottle holds 2.6

gallons. The 427 model bottles hold 2.75 gallons each.

9. A fill hose that fits most faucets is provided with your humidifier. Fill the bottles with cool, fresh

(preferably unsoftened) water. If you only have softened water available in your home, you can use it,

but mineral buildup will occur more quickly.

NOTE: For optimum running time, fill each water bottle, tighten the cap, and place inside unit. Do not fill the

reservoir bucket, as overfilling will result in water damage. Use only the bottles provided. One bottle will

drain until the reservoir is filled. Remove the partially emptied bottle and refill it. Place back in humidifier

cabinet.

CAUTION: When filling, be careful not to pressurize the bottle by overfilling it. Bottle damage can result

from this, and will not drain properly.

NOTE: On initial fill up, it will take approximately 20 minutes for the reservoir to fill because the dry wick has

to absorb water. Subsequent fillings will take approximately 12 minutes, since the wick is already saturated.

10. After the filling process is complete, insert the water bottles into the humidifier, placing them with the

valve cap end down, so that the groove in the water bottle faces the inside.

11. After filling, replace the water bottle cover and place the chassis/power pack unit into the cabinet, so it

fits without tipping or rocking.

1041 WICK

CONTROLS AND OPERATION

1. Plug cord into wall receptacle. Your humidifier is now ready for

use. The humidifier should not be near any heat registers. Place

the unit at least FOUR inches away from any walls. Unrestricted

airflow into the unit will result in the best efficiency and

performance.

2. Access the control panel by opening the panel door (427 Model).

Depending on which model, you may have a choice of 2 speed or

variable fan speed allowing you to use the low setting for the

quietest operation or a high setting for maximum output.

NOTE: When excessive condensation exists, a lower speed setting

is recommended.

NOTE: Each model has an automatic humidistat. The humidistat will

turn the humidifier on when the relative humidity in your home is

below the humid- stat setting and will turn the humidifier off when the

relative humidity reaches the humidistat setting.

3. For initial operation, set the humidistat at its midpoint “comfort

zone” setting and adjust up or down from there to achieve the

desired humidity level. Turning the Humidity Control knob all the

way counterclockwise will turn the unit off regardless of the

relative humidity. This must be turned on again before the unit will work.

4. One bottle is designed to empty first. The refill light will indicate when the respective bottle is out of

water. When the unit is completely out of water, the motor will shut off.

OPTIONAL AIRCARE® FILTER

The optional Aircare® filter is a excellent means of cleaning the air while using your humidifier. The first

stage of the air filter is a high-efficiency, electrostatically charged filter media which traps dust, pollen, and

airborne pollutants. The second stage is an activated carbon media which absorbs odors from cooking, pets,

or tobacco smoke.

We recommend replacing the AirCare® filter at least once a year and more often if necessary. When the white

filter media is coated with a layer of dust and dirt, it is time to replace the AirCare® filter. The certified water

output of your humidifier will be reduced when using the AirCare® filter. AirCare® filters are optional and are

not required for normal operation of the humidifier. AirCare® is registered trademark of Essick Air Products.

CARE AND MAINTENANCE

Cleaning your humidifier regularly helps eliminate odors and bacterial and fungal growth. Ordinary household

bleach is a good disinfectant and can be used to wipe out the humidifier base and bottle/reservoir after

cleaning. We recommend cleaning your humidifier at least once every two weeks to maintain optimum

environmental conditions for your home.

We also recommend using Essick Air Bacteriostat Treatment each time you refill your humidifier to eliminate

bacterial growth. Add bacteriostat according to the instructions on the bottle. Please call 1-800-547-3888 to

order Bacteriostat Treatment reference part number 1970.

1. Turn off unit completely counterclockwise and unplug from outlet.

2. Lift out the water bottle and the power pack.

3. Carry bottle and base to cleaning basin. Lift wick from the base allowing the water to drain. Rinse wick

under fresh water only. Do not use soap, detergent, or any other cleaners on the wick. Leave in sink to

drain.

REMOVING SCALE

4. Empty the water from the reservoir and water bottle. Fill reservoir and each water bottle ½ full with water

and add 8 oz. (1 cup) of white vinegar to each. Let stand 20 minutes. Then empty solution.

5. Dampen a soft cloth with white vinegar and wipe out reservoir to remove scale. Rinse the water bottle and

reservoir thoroughly with fresh water to remove scale and cleaning solution before disinfecting.

DISINFECTING UNIT

6. Fill each water bottle and reservoir ½ full with water and add 1 teaspoon of bleach to each. Wipe cabinet

and bottle surfaces with this solution. Let solution stay for 20 minutes, then rinse with water until bleach

smell is gone. Dry with clean cloth. The outside of the unit and water bottle may be wiped down with a

soft cloth dampened with fresh water.

7. Refill unit and re-assemble per ASSEMBLY instructions.

SUMMER STORAGE

1. Clean unit as outlined in Care & Maintenance section.

2. Discard used wick and any water in the reservoir or bottle and allow to dry thoroughly before storage. Do

not store with water inside reservoir or bottle.

3. Do not store unit in an attic or other high-temperature area.

4. Install new filter at beginning of season.

ESSICK AIR PRODUCTS

HUMIDIFIER WARRANTY POLICY

EFFECTIVE APRIL 1, 2008

SALES RECEIPT REQUIRED AS PROOF OF PURCHASE

FOR ALL WARRANTY CLAIMS.

This product is warranted against defects in workmanship and materials for one year

from the date of sale except for motors, which are warranted for two years. This

warranty does not apply to filters or wicks which are customer-replaceable parts.

This warranty applies only to the original purchaser of the product when it is purchased

from a reputable retailer/dealer.

This warranty does not apply to damage from accident, misuse, alterations,

unauthorized repairs, unauthorized use, mishandling, unreasonable use, abuse,

including failure to perform reasonable maintenance, normal wear and tear, nor where

the connected voltage is more than 5% above the nameplate voltage, nor to the

equipment or products being improperly installed or wired or maintained in violation of

this Owner’s Manual.

Alterations include the substitution of name brand components including, but not limited

to wicks and bacteria treatment.

THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. THIS IS THE SOLE

AND EXCLUSIVE WARRANTY GIVEN BY MANUFACTURER WITH RESPECT TO

THE PRODUCTS AND, TO THE MAXIMUM EXTENT PERMITTED BY LAW, IS IN

LIEU OF AND EXCLUDES ALL OTHER WARRANTIES AND CONDITIONS,

EXPRESS OR IMPLIED, ARISING BY OPERATION OF LAW OR OTHERWISE,

INCLUDING WITHOUT LIMITATION, MERCHANTABILITY AND/OR FITNESS FOR A

PARTICULAR PURPOSE.

No employee, agent, dealer or other person is authorized to give any warranties or

conditions on behalf of the manufacturer. The customer shall be responsible for all

costs incurred in the removal or reinstallation and shipping of the product for repairs.

Within the limitations of this warranty, purchaser with inoperative units should

contact customer service @ 800-547-3888 for paperwork and instructions on the

return of the unit for repair. A copy of the sales receipt is required before

authorization to return a unit for repair is approved. The manufacturer will repair or

replace the product, at its discretion, at no charge to the customer with return freight

paid by the manufacturer. It is agreed that such repair or replacement is the exclusive

remedy available from the manufacturer and that TO THE MAXIMUM EXTENT

PERMITTED BY LAW, THE MANUFACTURER IS NOT RESPONSIBLE FOR

DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL

DAMAGE OR LOSS OF PROFITS OR REVENUES.

This warranty will be null & void if purchaser attempts to repair or replace any

parts which are mechanical or electrical.

The warranty gives the customer specific legal rights, and the customer may also have

other rights which vary from province to province, or state to state.

MANUAL

CUIDADOS

USO DEL

PROPIETARIO

LEA Y GUARDE ESTAS INSTRUCCIONES

HUMIDIFICADOR

VAPORIZADOR

427 300, NUDO DE ROBLE – 2 velocidades

696 400, ROBLE – Velocidad variable

697 500, CEREJEIRA – Velocidad variable

• Humidistato Automático

• Apagado automático

• Funcionamiento silencioso para uso nocturno

• Fácil de limpiar, unidad de fuerza removible

CUIDE EL MEDIOAMBIENTE

RECICLE LOS MATERIALES APROPIADOS

Patentes: 5,037,583; 5,110,511; 5,133,904

Otras patentes pendientes

Para encomendar piezas y accesorios,

llame al 1-800-547-3888

French and Spanish

Instructions included.

Se incluyen instrucciones

en español y francés.

Directives en Français et en

espagnol compris

696 400 427 300

697 500

1B71817 4/08

Page is loading ...

Essick 427 300 Care & Use Manual

Brand: Essick

Model: 427 300

Category: Dehumidifiers

Type: Care & Use Manual

This manual is also suitable for

Download PDF

report

in other languages

français: Essick 427 300
español: Essick 427 300

Essick 427 300 Care & Use Manual

This manual is also suitable for

Essick 427 300 Care & Use Manual

in other languages

Related papers

Other documents