7. Use screws
B
(M5 × 20 mm) (6 pcs.) to fasten the side boards
and the speaker box.
Speaker cable
Pedal cord
Screw
B
x 6
Initially tighten
the screws two
or three turns by
hand, and then
use a screwdriver
to tighten them
rmly.
2. Install the Piano onto the Stand
1. Align the screws on the bottom of the piano unit (one each at
left and right) with the metal xtures of the side boards, and
while lifting up the keyboard side of the piano 1–2 cm, engage
the screws in the metal xtures.
While lifting the
keyboard side,
push the piano
toward the rear.
Be careful not to
get your ngers
pinched.
2. Use screws
B
(M5 × 20 mm) (2 pcs.) to fasten the piano and
the stand.
Initially tighten
the screws two
or three turns by
hand, and then
use a screwdriver
to tighten them
rmly.
Screw
B
3. Connect the speaker cable to the speaker jack on the bottom
of the piano, connect the AC adaptor to the DC In jack, and
connect the pedal cord to the Pedal jack.
* As shown in the illustration, use the cable fastener to secure the AC adaptor and
the pedal cord.
Speaker cable
Insert until you hear
it click.
Cable fastener
Pedal cord AC adaptor
Keyboard side
4. Provisionally tighten thumbscrews
E
(2 pcs.), and insert the
rear board.
Notch
Provisionally tighten
the screws in the lower
holes.
Leaving a small gap, t
the notch over the shaft
of the screw.
Thumbscrew
E
x 2
5. Use thumbscrews
E
(2 pcs.) to fasten the upper part of
the rear board, and then rmly tighten the thumbscrews
(2 locations) at the lower part of the rear board that you
provisionally tightened in step 4.
Thumbscrew
E
x 2
AC adaptor
6. Use two screws
C
(M4
×
16 mm) to fasten the headphone hook
D
.
Screw
C
x 2
7. Connect the supplied AC adaptor and power cord.
To AC outlet
Power cord
Place the AC adaptor so the side with the indicator faces upwards and
the side with textual information faces downwards. The indicator will
light when you plug the AC adaptor into an AC outlet.
8. Adjust the Adjuster.
Lower the adjuster located under the pedal board, so that it contacts the
oor. If the unit is placed on carpet, lower the adjuster further so that it
presses slightly against the oor.
Adjuster
* The pedal may be damaged if there is a gap between the adjuster and the oor.
Parts check
• To assemble this product correctly, carefully read these instructions before assembly. Keep these instructions nearby so that you can immediately refer to
them when necessary.
• When assembling or moving this product, lift it in a horizontal position.
• Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet.
• Make sure that another person is on hand to help with the assembly and setup.
• Place screws and other small parts out of reach of small children so that they will not be accidentally swallowed.
• Screws should rst be tightened provisionally, and then rmly tightened later. When tightening a screw provisionally, leave about half of it exposed.
• Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
• Prepare an area in which you can perform the assembly safely.
* After rmly tightening all the screws, place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk
causing damage to the pedals due to instability and unnecessary movement.
* The surface of the piano unit and the stand are very delicate; handle with care to avoid scratching them.
* Do not place the piano unit directly on the oor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano.
When moving or transporting the piano
When you need to move the piano, you should rst close the keyboard cover. If
the piano has a top lid or a music rest, fold them down. Then disconnect the AC
adaptor and raise the adjuster of the stand. Also detach the headphone hook.
When moving the unit, at least two people should work together and lift the unit
carefully, all the while keeping it level, and being very careful so as not to pinch
your hands or drop the unit on your feet.
1. Assembly Procedure
* For successful assembly, you should rst assemble the entire product with the
screws tightened only loosely; then while making sure that all parts are aligned
correctly, tighten the screws rmly.
* To prevent the stand or the oor from being scratched, cover the assembly area
with a blanket or similar cushion as necessary.
* While working, take care not to pinch the pedal cord.
1. As shown in the illustration, place the left and right side boards
against the pedal board so that their metal xtures are on the
inside, and use screws
A
(M6 × 40 mm) (4 pcs.) to fasten them
provisionally.
Screw
A
x 2
Screw
A
x 2
As seen from below
Leave the pedal
cord extended
Initially tighten the screws
two or three turns by hand,
and then use a screwdriver
to tighten them.
* If you omit initially tightening them
by hand, the screw threads might be
stripped, making assembly impossible.
2. Place the speaker box from the direction shown by the arrows.
* Take care that the speaker box does not strike the pedal cord or the metal xtures
of the side boards.
Don’t contact!
3. Provisionally fasten the pedal board and speaker box using
screws
B
(M5 × 20 mm) (4 pcs.).
Initially tighten
the screws two
or three turns by
hand, and then
use a screwdriver
to tighten them.
Screw
B
x 4
4. Using a screwdriver, rmly tighten screws
A
(4 locations) and
B
(4 locations) that you provisionally tightened in steps 1 and
3, working in the order of screws
A
and then
B
.
* Assemble the parts so that there is no gap between the side boards and the pedal
board.
5. Use screws
B
(M5 × 20 mm) (2 pcs.) to fasten the side boards
and the speaker box.
Initially tighten
the screws two
or three turns by
hand, and then
use a screwdriver
to tighten them
rmly.
Screw
B
x 2
6. With the help of another person, and each person grasping the left and
right side board respectively, raise the stand to the upright position.
* The screwdriver required for assembly is not included. Obtain a Phillips screwdriver of the
appropriate size for each screw (sizes: #2, #3).
©2018 Roland Corporation
Stand Assembly
1
2
3
4
5
A
Screw (M6 x 40 mm) x 4
B
Screw (M5 x 20 mm) x 14
C
Screw (M4 x 16 mm) x 2
D
Headphone hook x 1
E
Thumbscrew x 4
1
Side board (left)
2
Side board (right)
3
Pedal board
4
Speaker box
5
Rear board
* 5 1 0 0 0 6 4 1 8 4 - 0 1 *
1
-
1
