Shark S3801CO Quick start guide
- Category
- Steam cleaners
- Type
- Quick start guide
STEAM MOP ASSEMBLY USING YOUR STEAM MOP INTELLIGENT STEAM CONTROL
®
STEPS TO A SHARK
®
CLEAN FLOOR
Steam Pocket
®
Mop
PROFESSIONAL
* Sanitization studies were conducted under controlled test conditions, using Rectangle Mop
Head only. Household conditions and results may vary. See Owner’s Guide for instructions.
** Please consult your flooring manufacturer’s care and maintenance instructions
before applying any cleaning products or solutions, including vinegar.
* Sanitization studies were conducted under controlled test conditions, using Rectangle Mop
Head only. Household conditions and results may vary. See Owner’s Guide for instructions.
1 Slide the mop handle into the mop body. Insert the screw provided and tighten. (Fig. 1)
1 SWEEP OR VACUUM YOUR FLOOR
We recommend the use of Shark Vacuum or Sweeper to clean up dust and
debris before using your Steam Mop.
2 SANITIZE
*
WITH A SHARK
®
STEAM MOP
Shark Steam Mops provide sanitization
*
and are great for cleaning
up stuck on dirt, grime, and footprints.
3 REGULAR MAINTENANCE IS KEY
Daily spot cleaning is recommended to keep dirt and grime from building
up in your home.
The range of convenient, quick-clean products from Shark is guaranteed to
help you keep a clean and sanitized* home.
** TIP: First time users may experience some streaking or clouding after the
initial use. This may be the result of your Steam Mop removing residue from
chemicals and polishes previously used on your floors. With regular use these
effects will diminish. For more stubborn cases, you may need to rinse the floor
with a mix of one part vinegar and two parts water. Remember, a clean mop
pad is essential for residue removal.
WARNING: Your Steam Mop is designed to clean hard floor surfaces that will
withstand high heat. Do not use on unsealed wood or unglazed ceramic floors.
On surfaces that have been treated with wax or some no wax floors, the sheen may
be removed by the heat and steam action. It is always recommended to test an
isolated area of the surface to be cleaned before proceeding. We also recommend
that you check the use and care instructions from the floor manufacturer.
2 Fit the microfiber cleaning pad on the
mop head. (Fig. 2)
4 Open the water tank cap, fill the tank with water, then replace and tighten the cap. (Fig. 4)
NOTE: We recommend using distilled water to prolong the life of your Steam Mop.
Fig. 2
5 Sweep or vacuum floors prior to cleaning with the Steam Mop.
6 Plug the power cord into an outlet. The STEAM CONTROL button will flash blue.
7 Press the STEAM CONTROL button to select your steam setting:
Once for DUST, twice for MOP, and three times for SCRUB. Pressing a fourth time will
place the unit on standby. (Fig. 5 & Intelligent Steam Control
®
chart)
NOTE: To put the unit in STANDBY MODE, press the STEAM CONTROL button until it is
flashing blue. This will stop the unit from steaming without shutting it off. Remember to
never leave a damp steam mop in one spot for an extended period of time.
8 After use, unplug and wait 2 to 5 minutes so the unit can cool before storing away.
Setting Recommended Usage
Light Steam
Normal Steam
Heavy Steam
Light cleaning and dusting
Loosening and lifting light dirt
Sanitizing* floors
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavily-trafficked areas
Sanitizing* floors
Tough cleaning and removal of stuck-on messes
and stains
Deep cleaning heavily-trafficked areas
Cutting through heavy dirt and grime
Sanitizing* floors
DUST
MOP
SCRUB
S3801CO_QSG_150916
Paper: Quality A (Bright White) 157g/m2
Coating: Matte both sides
3 Snap the Steam Mop housing onto the
mop head. (Fig. 3)
Fig. 1
Fig. 3
Fig. 4
Fig. 5
Please be sure to read the enclosed Owner’s Guide prior to using your unit.
DANGER OF SCALDING: Steam emitted is very hot.
Use caution when using the steam mop.
Looking for replacement parts or accessories? Check out sharkclean.com or give our Customer Care Center a call at 1-800-798-7398.
PROBLEM RESOLUTION CHECKLIST
ISSUE RESOLUTION
The Steam Mop will not turn on.
(There are NO blue lights illuminated.)
Ensure the power cord is plugged in correctly to a working
120-volt outlet.
The Steam Mop will not make steam.
Verify the Steam Control button is illuminating solid blue indicating a
steam setting has been chosen. Ensure that the unit is filled with water.
You cannot activate a steam mode on the Steam Mop.
(Blue light remains flashing.)
Unplug the unit from the outlet, wait 15 to 30 seconds, then plug the
unit back in.
The Steam Mop is leaving water on the floor or is hard to push.
Make sure the cleaning pad is properly affixed to the mop head and
not overly saturated. If it is overly saturated, unplug the unit, wait 2 to 3
minutes for the pad to cool, and then replace with a clean, dry pad.
The Steam Mop left a white spot on the floor.
White spots may occur if you leave a wet pad idle for an extended period of
time. If you are not activly mopping, do not leave the pad touching the floor.
Floors are cloudy, streaky, or spotty after steaming.
This may be the result of residue from chemicals previously used to
treat the floor. Be sure to follow the “Steps to a Shark
®
Clean Floor”
and the “Pad Care Guide” in your Owner’s Guide to prevent this issue.
Unable to resolve your issue?
If you are still having difficulty using your Steam Mop, give our
Customer Care Center a call at 1-800-798-7398.
For more information please visit sharkclean.com
or call us at 1-800-798-7398
S3801CO_150909
Join The Clean Evolution.
™
When it comes to cleaning, we’re not afraid to
get our hands dirty. At Shark, we’re constantly
working to evolve and innovate products to
meet the needs of people like you. Because our
job is to make 5-star worthy products that make
your life a whole lot easier.
QUICK START GUIDE
-
1
Shark S3801CO Quick start guide
- Category
- Steam cleaners
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
